Hitachi CP-X940W/E specifications Installation, Example of the projector and screen installation

Page 12

Installation

Example of the projector and screen installation

Determine picture size and projection distance as illustrated below.

View from the top

View from the side

Screen

Lens center

a

Screen (inch)

a (inch)

 

 

 

 

Minimum

Maximum

 

 

 

 

 

 

40

64

84

 

 

 

 

 

 

60

97

127

 

 

 

 

 

 

80

130

169

 

 

 

 

 

 

100

163

213

 

 

 

 

 

 

120

196

256

 

 

 

 

 

 

150

244

319

 

 

 

 

 

 

200

326

 

 

 

 

 

 

 

 

 

 

 

a:Distance from the projector to the screen. (tolerance : ±10%)

This screen size is full-screen size.(1024 dots X 768 dots)

Installation of liquid crystal projector

Please basically use liquid crystal projector at the horizontal position.

If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage.

Be especially careful not to install it with ventilation holes blocked.

How to use foot adjusters

Adjust the projection position using the foot adjusters at the bottom of the projector.

View from the front

View from the side

Foot adjuster

Vertical adjustments can be made in the range of 0 to 9°.

Horizontal inclination may be adjusted using the adjuster at the rear.

1.Lift up the projector and press the button of the adjuster to release the lock.

2.Adjust the projection angle, release the button of the adjuster and securely lock it.

3.To adjust the angle slightly, revolve the foot adjusters.

Caution

Do not unlock the foot adjusters while you do not support the projector, to avoid falling of the projector and causing an injury.

Do not revolve the foot adjusters by force, the foot adjusters is damaged.

Securely lock the adjuster.

Do not apply unnecessary force from the upper side when lifting the projector. Otherwise, projector may be damaged or a finger could be caught and cause injury.

12

Image 12
Contents Features ContentsOutline Operating GuideFor the Customers in U.K Video signal cables Power cordBefore use Instructions to UsersDo not look directly at the lens when Lamp is lit Do not install this unit in an unstable placeDo not use power supplies other Than that specified If any abnormality occursDo not stare directly into the laser aperture Class 2 Laser ProductCleaning Handle the power cord carefullyDo not step on this unit or do not put a Heavy object on it Do not block the ventilation holesWhen you are not going to use For a long time Do not place this unit where it gets hotVolume Cleaning the lensContents of shipping box Names and functions of each partRemote control sensor Main Power switch AC in socketVideo input terminal RGB input terminalRemote control transmitter How to insert batteries Remove the battery compartment coverInstallation Example of the projector and screen installationHow to use foot adjusters On indicator will light up orange Basic operationsTo project the picture For 3 secondsTo turn off the power Indicator lights up orangeStandby mode PLUG&PLAYFreeze Function Magnifying FunctionAdjustments and functions To return to the initial settingMemory function On-screen menus are displayed on the screenSET UP How to use the SET UP menuAdjustment Item Details of adjustment Freeze Magnify Operation is not possibleAUTO-adjustment AUTO-adjustment Confirm ScreenDuring AUTO-adjustment Adjustment Item Details of adjustmentImage The menu Image serves of the picture inversion MirrorConnection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Horizontal Timing µsConnection to the control signal terminal Control signal terminalPS/2 mouse ADB Mac mouseSerial mouse Control command table Control command tableCommunication RS232C cable ReferenceControl data table Procedure of getting the Projector status Procedure of setting the Projector statusProcedure of default setting the Projector status Example of command errorExample of system setup Connecting various equipmentAC Inlet Computer Note type ComputerDesk typeCleaning the air filter Air filter Filter coverDo not use with removed air filter Remove the lamp cover Loosen two screws and pull Handle to removeLamp Install the lamp cover and fix it using screws Reset the lamp timeLamp Message tableIndicator display Blink in the following casesDimension diagram Product name Liquid crystal projector Model name CP-X940W/ERCA Jack terminal Input terminal Input/Output RCA Jack terminal Terminal

CP-X940W/E specifications

The Hitachi CP-X940W/E is a high-performance projector that stands out for its vibrant image quality, versatile features, and user-friendly design. This projector is particularly suited for educational and corporate environments, delivering clear and impactful presentations.

One of the flagship features of the CP-X940W/E is its impressive brightness level, reaching up to 4,000 lumens. This ensures that images remain sharp and vivid even in well-lit rooms, making it ideal for classrooms and conference halls. Additionally, the device has a contrast ratio of 10,000:1, which helps in producing deep blacks and bright whites, enhancing the overall picture quality. It supports a native WXGA resolution (1280 x 800), providing a great balance of detail and clarity for various content types.

The CP-X940W/E employs advanced 3LCD technology, which outshines typical DLP projectors by delivering more accurate colors and consistent brightness across its color spectrum. This technology significantly reduces color break-up and ensures smooth, natural color transitions, making it an excellent choice for showcasing high-definition content.

Connectivity is another strong point of the Hitachi CP-X940W/E. It features multiple input options, including HDMI, VGA, and USB ports, as well as support for wireless display technology. This versatility allows users to connect a wide range of devices from laptops to smartphones effortlessly. The projector also supports network control and monitoring, enabling IT managers to oversee multiple projectors in an organization with ease.

The projector is designed for longevity and ease of maintenance. It has a lamp life of up to 7,000 hours in eco mode, reducing the frequency of replacements and lowering overall operating costs. Its filter-free design means less maintenance hassle, contributing to a lower total cost of ownership.

Additionally, the Hitachi CP-X940W/E includes user-friendly features such as automatic keystone correction and a built-in speaker, simplifying setups and providing enough sound for small to medium-sized rooms. The projector also comes with a comprehensive remote control, enhancing convenience during presentations.

In summary, the Hitachi CP-X940W/E is a robust projector that combines advanced display technologies, flexible connectivity options, and user-centric features. It's an ideal choice for those looking to enhance their visual presentations, making it a trusted tool for education and business alike.