Hitachi CP-X935W Lamp, Message table, Install the lamp cover and fix it using screws

Page 30

Lamp (continued)

5

Install the lamp cover and fix it using screws.

￿ To prevent burn, install the lamp cover and secure it using the screws.

 

￿ Do not turn on the power with lamp cover removed.

 

Lamp cover

 

 

 

Whenever the lamp is replaced, reset the total operation time of the lamp.

Do not reset if the lamp has not been replaced.

Screw

2. Reset the lamp time

Pleasecarry out the following operationwithin 10 minutes from power on, if you replacedthe lamp after

2,000 hours.

MAGNIFY VOLUME

3

2

OFF

 

 

 

 

POSITION ON

LASER

 

 

STANDBY/ON

 

 

 

 

 

 

 

 

INPUT

 

 

 

 

MUTE

 

 

1

 

MENU

RESET

RIGHT

 

3

MENU ON

MOUSE ON

1, 2

 

 

 

RESET

BLANK

TIMER

 

 

RGB

VIDEO

 

 

 

INPUT

 

 

 

1)Pressthe RESET button on projector for 3 secondsor remote control TIMER button for 3 seconds and display the total lamp used time.

￿When accumulatedoperation time of the lamp reaches1700 hours, the following display will appear at the bottom of the screen.

2)Pressthe RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the ￿0￿ on the screen using the MENU () button or DISK PAD.

LAMP 1700 h

LAMP 1700 ￿￿0 ￿¡CANCEL

Message table

On-screen display

The following messages are displayed on the screen.

MESSAGE

Action

 

 

CHANGE THE LAMP

Accumulated operation of lamp has exceeded 1,700 hours. It is recommended

AFTER REPLACING LAMP,

to replace lamp. Replace with new lamp. If accumulated operation reaches

RESET THE LAMP TIMER.

2,000 hours, lamp will automatically turn off. * 1

CHANGE THE LAMP

Lamp has 1,979 hours on it.

AFTER REPLACING LAMP,

Call a maintenance person. * 1

RESET THE LAMP TIMER.

Time is 20 ~ 0. (count down.)

THE POWER WILL TURN

 

OFF AFTER 20 Hr.

 

 

 

Blinking of

When the lamp has 2,000 hours or more on it, the message will blink, and the

CHANGE THE LAMP

power will turns off after 10 minutes.* 2

 

 

NO INPUT IS DETECTED

Signal is hot input. (See page 19, 20)

 

 

SYNC IS OUT OF RANGE

The horizontal frequency of the input signal exceeds the range of the projector,

it cannot be displayed. (See page 20, 21)

 

 

 

*1 This message are not displayed after 3 minutes.

But this message are displayed when you turn on the power again.

*2 It is possible to again turn on the power, however the power will go off after about 10 minutes.

30

Image 30
Contents Outline FeaturesContents Operating GuideFor the Customers in U.K Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursHandle the power cord carefully Be careful in handling the power cordCleaning Do not step on this unit or do not put a Heavy object on itDo not place this unit where it gets hot When you are not going to use For a long timeClean inside the unit at least once two years VolumeContents of shipping box Names and functions of each partVideo input terminal Remote control sensor Main Power switchAC in socket RGB input terminalRemote control transmitter How to insert batteries Remove the battery compartment coverInstallation Example of the projector and screen installationHow to use foot adjusters Basic operations To project the pictureStandby mode To turn off the powerIndicator lights up orange PLUG&PLAYFreeze Function Magnifying FunctionMemory function Adjustments and functionsTo return to the initial setting ∙ On-screen menus are displayed on the screenAdjustment Item Details of adjustment SET UPHow to use the SET UP menu Manual OperationInput Auto-adjustmentDuring AUTO-adjustment Auto Confirm ScreenMenu Image serves of the picture inversion ImageOPT Menu OPT. allows you to control communication function etcConnection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Connection to the control signal terminal Control signal terminalPS/2 mouse ADB Mac mouseSerial mouse Communication Control command tableControl command table RS232C cable ReferenceConnection to the control signal terminal Control data tableProcedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorExample of system setup Connecting various equipmentCleaning the air filter Attach the air filter on the coverLoosen two screws and pull the handle to remove Lamp How to replace lampRemove the lamp cover Option lamp Lamp unit CP-X935W/E DT00201Lamp Install the lamp cover and fix it using screwsReset the lamp time Message tableIndicator display Blink in the following casesDimension diagram All dimensions shown in inches

CP-X935W specifications

The Hitachi CP-X935W is a versatile and powerful projector designed to meet the demands of both educational and business environments. With its cutting-edge technologies and a range of features, the CP-X935W stands out as an excellent choice for those seeking high-quality visuals and reliable performance.

One of the standout features of the CP-X935W is its impressive brightness rating of 3,300 ANSI lumens. This high level of brightness ensures that presentations and videos remain clear and visible even in well-lit rooms, making it an ideal projector for classrooms, conference rooms, and large venues. The projector also boasts a native WXGA resolution of 1280 x 800 pixels, allowing for crisp and detailed images that enhance the viewing experience.

The CP-X935W utilizes Hitachi's sophisticated DLP technology, which is known for delivering vibrant colors and sharp imagery. This technology minimizes the risk of image distortion and offers a high contrast ratio, which helps to produce deeper blacks and more vivid colors. The projector also features a 1.5x optical zoom lens, providing flexibility in placement without compromising image quality.

In terms of connectivity, the Hitachi CP-X935W offers a wide range of options. It includes HDMI, VGA, and USB ports, allowing users to easily connect laptops, Blu-ray players, and other multimedia devices. The inclusion of wireless presentation capability means that users can project content directly from their mobile devices without the need for cumbersome cables, enhancing the ease of use in dynamic presentation scenarios.

Additionally, the CP-X935W incorporates advanced lamp technology for improved longevity. The lamp life can reach up to 6,000 hours in eco mode, significantly reducing the total cost of ownership and maintenance. This feature is particularly advantageous for educational institutions and businesses with frequent projector use.

User-friendly features such as a remote control, intuitive on-screen menu, and quick start-up time further enhance the overall experience. The projector also supports various image adjustment features, including keystone correction and screen resizing, ensuring a perfect fit for any projection surface.

In conclusion, the Hitachi CP-X935W is a powerful projector that blends advanced technology with user-friendly features. Its high brightness, versatile connectivity options, and exceptional image quality make it a top choice for anyone looking to elevate their presentation experience. Whether in a classroom or a conference room, the CP-X935W is designed to deliver reliable performance and stunning visuals.