3. OPERATION
Connecting the Power Cable and Turn on the Projector
Before you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.
1 Connect the supplied power cable to the projector.
|
|
| SELECT | N |
|
|
|
| L |
|
|
|
| E |
|
|
|
| C |
|
|
|
| CA |
|
|
| ENTER |
|
| ST |
|
|
|
| JU |
|
|
|
| AD |
|
|
|
| TO |
|
|
|
| AU |
|
|
|
| CE |
|
|
|
| UR |
|
|
|
| SO |
|
|
|
/ | BY |
| RGB |
|
ON | ND |
|
|
|
STA |
|
|
| |
| IDEO |
| IN | |
R |
|
| AC | |
|
|
| ||
WE | VIDEO |
|
|
|
|
|
|
| |
| AUDIO |
|
|
|
| OL |
|
|
|
| NTR |
|
|
|
| CO |
|
|
|
| PC |
|
|
|
Plug the supplied power cable in the wall outlet. The pro- jector will go into its standby mode and the power indica- tor will glow orange.
2 Turn on and off the Projector.
Power button
RGB VIDEO
AUTO ADJ.
MAGNIFY 
VOLUME
To turn off the projector:
First press the “POWER” button on the projector cabinet or the remote control for a minimum of two seconds. The power indi- cator will glow orange. After the projector turns off, the cooling fans keep operating for 90 seconds.
NOTE: Do not disconnect the power cable during this time. Then, un- plug the power cable. The power indicator will go out.
Status of indicator light: turn on
Normal mode:
stand by
STATUS | ON/STAND BY | ||
POWER |
|
| |
steady orange light |
|
| |
| STATUS | STATUS | |
| POWER | POWER | |
| flashing green light | steady green light | |
Eco mode: | for one minute |
| |
|
| ||
stand by |
|
| |
STATUS | ON/STAND BY | ||
POWER | |||
|
| ||
steady orange light |
|
| |
| STATUS | STATUS | |
| POWER | POWER | |
PICTURE FREEZE MUTE ASPECT
MENUHELP
ENTERCANCEL
POWER ON/STAND BY button |
| |
STATUS |
|
|
POWER |
|
|
ON/ |
|
|
STAND | BY |
|
|
| |
| SOUR | CE |
|
| |
Indicator |
|
|
flashing green light | steady green light |
for one minute | (Eco mode) |
(Normal mode) |
|
Status of indicator light: turn off |
|
ON |
|
POWER | ON/STAND BY |
| |
| press a minimum of |
steady green light | two seconds |
|
cooling down | stand by |
To turn on the projector:
Only after you press the “POWER” button on the projec- tor cabinet or the remote control will the power indicator turn to green and the projector become ready to use.
NOTE: To turn the projector on by plugging in the power cable, use the menu and enable the “Auto Start” feature. (See page E- 32.)
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
POWER | POWER |
change to flashing | steady orange light |
green light |
|
3 Adjust a Projected Image.
Select the Computer or Video Source
SOURCE |
|
AUTO | ADJUST |
|
E N
T E R
MENU
SELECT
CANCE L