Kyocera FS-1200 manual Adhesive-Backed Labels, Table B.3 Transparency Specifications

Page 105

B.3. Special Paper

Transparency

Transparency must be able to withstand the heat of fusing during the printing process. It should satisfy the conditions in Table B.3.

Table B.3 Transparency Specifications

Item	Specification

Tolerance of heat	Must tolerate at least 190°C (374°F)

Thickness	0.100 to 0.110 mm (3.9 to 4.3 mils)

Dimensional accuracy	±0.7 mm (±0.0276 in)

Squareness of corners	90° ±0.2°

To avoid trouble, Transparency must be delivered face-up.

If Transparency jams frequently, pull the top of the sheet very gently as it leaves the printer.

Adhesive-Backed Labels

The basic rule for printing on adhesive labels is that the adhesive must never come into contact with any part of the printer. Adhesive paper sticking to the drum or rollers will damage the printer.

Label paper must be manually fed.

Label paper has a structure comprising three lay- ers, as shown in Figure B.1. The top sheet is printed on. The adhesive layer consists of pres- sure-sensitive adhesives. The carrier sheet (also called the linear or backing sheet) holds the labels until use. Due to the complexity of its composi- tion, adhesive-backed label paper is particularly likely to give trouble in printing.

Adhesive label paper must be entirely covered by its top sheet, with no spaces between the individ- ual labels. Labels with spaces in between are apt to peel off, causing serious jam problems.

Some label paper is manufactured with an extra margin of top sheet around the edge. Do not remove the extra top sheet from the carrier sheet until after printing is finished.

Top sheet (white bond paper)

Adhesive

Carrier sheet

Figure B.1 Adhesive-back label

Acceptable

Unacceptable

Top sheet

Carrier sheet

Table B.4 lists the specifications for adhesive			Figure B.2 Label arrangement
label paper.			Figure B.2 Label arrangement


Table B.4 Adhesive Label Specifications


Item		Specification

Weight of top sheet	44 to 74 g/m² (12 to 20 lbs/ream)

Composite weight	104 to 151 g/m² (28 to 40 lbs/ream)

Thickness of top sheet	0.086 to 0.107 mm (3.9 to 4.2 mils)

Composite thickness	0.115 to 0.145 mm (4.5 to 5.7 mils)

Moisture content	4% to 6% (composite)

B-5

Image 105

Contents FS-1200 Introduction Limited Warranty LicenseLimitation of Remedies Typeface Trademark Acknowledgement GeneralConforming to the Class B limits FCC statementSafety information Interface connectorsImportant note on the interface connectors Laser safetyCdrh regulations Ozone concentrationCE Marking Directive Declaration of Conformity U.S.ADeclaration of Conformity Australia ViiiCanadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the Printer Prolonged Non-useMoving the Printer Kyocera ECO-PRODUCT Action program EnergyMaintenance Features Print Engine FeaturesIntroduction Options Software FeaturesPrescribe 2e Programming Manual on CD-ROM CD-ROM Kyocera Digital LibraryTable of Contents Xvi Xvii Serial RS-232C/RS-422A Interface Option Appendix C Host Computer InterfacePositioning the Printer ClearancePlaces to Avoid Basic requirements Temperature 10C to 32.5C 50F to 90.5F Humidity 20% to 80%Voltage FrequencyUnpacking and Inspection Power SupplyList of Shipped Components Front View Names of PartsRear View Interior ViewSetting Up and Interfacing Install the toner containerOpen the top cover Close the top cover Install the waste toner bottleOpen the side cover on the left side of the printer Adjust the paper guides in the cassette and add paper Clip Open the paper stopper on the face-down output tray Install the face-up output trayAttach the power cord Connect the printer to the computerParallel interface Set the emulation mode Print a statusTest the interface with the computer Windows 95/Windows Install the printer driverCD-ROM Drive Name\drivers\Language\pcl\9x CD-ROM Drive Name\drivers\Language\kpdl\9x WindowsCassette Mode First Mode Automatic Manual FeedingMP Multi-Purpose Tray Feeding Duplex Printing from the MP trayMP Multi-Purpose Tray Feeding First Mode Automatic Manual FeedingFeeding Envelopes Cassette ModeMemory Card Handling a Memory CardTo Remove the Memory Card Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Installing and Removing The Dimm Installing DimmDimm to be used Removing Dimm Testing the Expansion MemoryControl Panel Operating the Laser PrinterResolution Indicator Interface IndicatorMessage Display Message MeaningCopy Indicator Paper Size IndicatorIndicator Name Description Symbolic IndicatorsKey Function Control KeysSwitching Power On Operating ProceduresStack Selection Feed SelectionCanceling Printing On-line/Off-line SettingStatus Printout Sample Status Form Feed Using the Mode Select Menu Mode Select MenuFunction Default Setting 2SWïý 520ý ý ý ý ý ý ý Parallel Interface Configuring InterfacesRAM Disk Operations Setting the RAM Disk SizeHints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Writing Data to a Memory CardDeleting Data from a Memory Card Printing a list of data names Formatting a Memory CardSetting Custom Sizes Setting the Paper Type Cassette, Media Type and Custom SettingsDuplex path Paper Type User Setting Making SettingsLvdeoh Submenus displayed Selection parameters DescriptionSleep Ecopower Mode Dumping Received Data Cancel keyKIR 2 Level Optimized stripes Ecoprint ModeDark vertical stripes White vertical stripesResource Protection Adjusting the Print DensityType of Error and Corresponding Audio Alarm Buzzer Setting the Audio Warning BuzzerSetting the Audio Warning Buzzer Internal Fonts FontsList of Fonts Internal Scalable and Bitmap FontsFont Number Font samples List of Fonts Kpdl Fonts List of Fonts Toner kit replacement interval Toner Kit ReplacementToner Kit to be Used Supplying TonerTo replace the toner container, proceed as follows Toner Kit Replacement Replace the Waste Toner Bottle Do not cap the new waste toner bottle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Interface Problems Power ProblemsCompletely blank printout Print Quality ProblemsAll-black printout Check the developer unitDropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panelGrey background Faint or blurred printingCharacters out of position Dirt on the top edge or back of the paperCheck the paper chute and the ramp Check the transfer rollerIndicators and Messages IndicatorsSymbolic Indicators Maintenance Messages Maintenance MessagesMessage Corrective Action DOO Vhuylfh Error Messages Error MessagesNing to ensure correct reading of the memory card 0025&$5 HUUúú Correcting a Paper Jam Printer SymbolRear Cover Power requirements Drum cleaningPower consumption Printing methodPrinter Specifications Table B.1 Specifications Paper SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Paper SizeMoisture Content Basis WeightSmoothness Thickness CaliperPaper type Media type Special PaperTable B.4 Adhesive Label Specifications Table B.3 Transparency SpecificationsTransparency Adhesive-Backed LabelsColored Paper EnvelopesPreprinted Paper Recycled PaperParallel interface communication modes Parallel InterfaceInterface Signals Table C.1. Parallel Connector Pin AssignmentsPin In/out Description Paper Empty PError Pin Data 0 1 to Data 7 8 Pins 2 toError* nFault Pin Power Ready PinInterface Signals Serial RS-232C/RS-422A Interface OptionRS-232C interface Serial Connector Overview of Signals RS-422ARS-422A interface RS-422A interface voltage levelsRS-232C/RS-422A Protocol RS-232C Cable Connection Prescribe Frpo D0 commandPreparing an RS-232C Cable H7 Buffer nearly-empty thresholdConnecting the Printer to the Computer Memory Card IndexIndex-2 Basic Operations During Mode Selection Mode Select MenuFrom Previous To 495 seconds