BATTERY SERVICE ACCESS
CASTER CENTERS
12mm DIA. THREADED MOUNTING HOLE (4) TYP.
(SEE NOTES 12 & 13)
(SEE DETAIL A)
NOTES:
1. | ALL DIMENSIONS ARE IN INCHES. |
2. | MIN CLEARANCE 36 INCHES IN FRONT, 12 INCHES |
AT TOP FOR AIR EXHAUST. | |
3. | KEEP CABINET WITHIN 15° OF VERTICAL WHILE |
HANDLING. | |
Figure 14
BIB
CONDUIT ENTRY 6.5 x 6.0
TOP ONLY
2 PLACES
MAX DOOR SWING 120°
2.72
12MM |
| CASTER |
CENTERS |
| |
| CENTERS | |
| FRONT | |
|
|
12MM THREADED |
|
MOUNTING HOLE | LEVELER |
12MM CENTERS
DETAIL A
4. | EXTERIOR CABLE ENTRY AVAILABLE THROUGH |
REMOVABLE TOP ACCESS PLATES. REMOVE, PUNCH | |
TO SUIT CONDUIT SIZE, AND REPLACE. | |
5. | CONTROL WIRING AND POWER WIRING MUST BE RUN |
IN SEPARATE CONDUIT. | |
6. | ALUMINUM AND COPPER CLAD ALUMINUM CABLES ARE |
NOT RECOMMENDED. | |
7. | ALL WIRING IS TO BE IN ACCORDANCE WITH |
NATIONAL AND LOCAL ELECTRICAL CODES. | |
8. | RECOMMENDED OPERATING TEMPERATURE RANGE: |
Outline Drawing,
BOARD
ACCESS
TOP VIEW
CENTER
GRAVITY
BOTTOM VIEW
CIRCUIT
BREAKER
CIRCUITMOTOR
BREAKER OPERATOR
OPTIONAL
DC BUS BARS
BATTERIES
NOTE:
(10)TRAY SHOWN.
(8)TRAY FOR FR200 BATTERY ASSY AND SMALLER
SUPPORT TRAY & SUPPORT BRACKET (SEE NOTE 15)
REAR OF UNIT SHOWN
WITHOUT SIDE PANEL
DC BUS BARS
CONTROL AND POWER WIRE SIDE ACCESS APPROX AREA 4.6 x 2.2
(BOTH SIDES)
CENTER
GRAVITY
9. COLOR - IBM OFF WHITE. |
10. UNIT BOTTOM IS STRUCTURALLY ADEQUATE FOR |
FORKLIFT HANDLING. |
11. APPROX WEIGHT OF CABINET IS 1500 TO 3000 LBS. |
12. THREADED MOUNTING HOLES USED FOR SEISMIC |
ANCHORING OR FLOORSTAND. NOTE, IF FLOORSTAND |
IS USED THE WEIGHT OF THE UNIT MUST BE |
SUPPORTED UNDER ALL CASTERS. |
13. EACH MOUNTING LOCATION IS SUPPORTED |
BY (2) 10 GA. (.135") GALVANIZED STEEL. THE THREADED 12MM INSERT IS APPROX. 3/4" DEEP.
MOUNTING BOLTS MUST BE THREADED INTO UNIT MOUNTING HOLES FROM UNDERNEATH UNIT BASE.
14.REFER TO DETAIL A FOR DIMENSION TO FRAME WITH SIDE PANEL REMOVED. SIDE PANELS ARE REMOVED BETWEEN ADJACENT UNITS WHICH ARE BOLTED TOGETHER.
15."BEFORE SLIDING OUT BATTERIES ON BATTERY TRAY" POSITION SUPPORT TRAY AND ATTACH TO CABINET. THEN SECURE (2) SUPPORT BRACKETS TO THE SUPPORT TRAY AND TO THE CABINET. REFER TO THE APPROPRIATE USERS MANUAL FOR FURTHER DESCRIPTION & DETAILS.
Battery Power Pack, 25-Inch Cabinet
Installation Drawings 33
FRONT VIEW | FRONT VIEW |
|
|
| |
WITH DOOR AND |
| SIDE VIEW |
| ||
|
|
| |||
WITH DOOR | WITH COVER REMOVED |
| |||
BARRIER REMOVED | DETAIL FOR DC BUS BARS | ||||
|
|
|
| ||
DRAWN BY |
|
|
|
| |
V CARMONA | OUTLINE DRAWING |
|
|
| |
CHK BY | DWG. NO. |
|
| ||
25" BATTERY CABINET |
|
| |||
|
| UBC11001 |
| ||
| NPOWER |
|
| ||
REF. DWG. | REV. NO. | DATE | 1050 DEARBORN DRIVE, | ||
| |||||
|
| 3 | 1/22/03 | COLUMBUS, OHIO 43229 | |
|
| FILE NAME: |
| ||