Emerson 185 manual Troubleshooting, Utility Acceptable light

Page 10

Series 185

TROUBLESHOOTING

This troubleshooting guide describes some of the simple causes of problems with the installation of the automatic transfer switch. Troubleshooting beyond the scope of this guide should not be attempted by the installer. A licensed electrician must perform all internal troubleshooting.

ASCO Power Technologies can be contacted at: 1–800–800–2726 or customercare@asco.com

ELECTROCUTION FLASH HAZARD Do not work on the transfer switch until both the utility and generator are off. Turn OFF both circuit breakers.

Problem

 

Cause and Solution

 

 

 

The Utility Acceptable light

1.

Verify that the utility feed is connected and that its circuit breaker is ON.

does not come on when utility

2. With ALL POWER OFF, verify that the utility feed is 220–240 V ac and 60 Hz.

power is connected to the ATS.

 

 

Check DIP switch S2 actuator 2, and DIP S1 actuator 4. See Table D for voltage

 

 

and frequency settings.

 

3.

With ALL POWER OFF, verify that the utility feed is wired to the terminal lugs

 

 

on the bottom of the transfer switch marked L1 and L5. See the wiring diagram.

 

4.

With ALL POWER OFF, verify that the transfer switch harness is connected

 

 

properly to the controller (plug and receptacle tight).

 

 

 

The generator does not crank

1.

Hold the Transfer Test button for at least 15 seconds.

when the utility source fails or

2.

Verify that the generator starting controls are set for automatic operation (not in

when the Transfer Test button is

pressed.

 

manual mode).

3.

Verify that the generator battery is connected and that the battery voltage meets

 

 

 

the generator manufacturer’s recommendation.

 

4.

Verify that the correct contact (normally open or normally closed) is being

 

 

utilized (see the generator manual).

 

5.

With ALL POWER OFF, verify engine start low voltage wiring between the

 

 

controller terminal block and the generator. See the wiring diagram. Check that

 

 

the plug is properly seated in the receptacle on the controller.

 

 

 

The generator cranks but does

1.

Verify proper generator operation (fuel in tank, oil level, spark plugs --- see

not start and run when the util-

 

generator manual).

ity source fails or when the

2.

With ALL POWER OFF, verify engine start low voltage wiring between the

Transfer Test button is pressed.

 

controller terminal block and the generator. See the wiring diagram. Check that

 

 

 

 

the plug is properly seated in the receptacle.

 

 

 

The generator starts and runs

1.

Verify that the generator feed is connected and that its circuit breaker is ON.

but the Generator Acceptable

2.

With ALL POWER OFF, verify that the generator feed is 220–240 V ac and 60

light does not come on.

 

Hz. Check DIP switch S2 actuator 2, and DIP S1 actuator 4. See Table D for

 

 

 

 

voltage and frequency settings.

 

3.

With ALL POWER OFF, verify that the generator feed is wired to the terminal

 

 

lugs on the top of the transfer switch marked L2 and L6. See the wiring diagram.

 

4.

With ALL POWER OFF, verify that the transfer switch harness is connected

 

 

properly to the controller (plug and receptacle tight).

 

5.

Verify generator ac output (voltage and frequency --- see generator manual).

 

 

 

The generator starts and runs

1.

Verify that the Generator Accepted light is on. If it is off, see previous trouble-

but the ATS does not transfer

 

shooting problem. The ATS will not transfer the load to an unacceptable source.

the load to the generator.

2.

With ALL POWER OFF, verify that the transfer switch harness is connected

 

 

 

properly to the controller (plug and receptacle tight).

 

 

 

381333–319 A

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Rating Label185 200 SeriesNameplate Catalog Number Identification 100 200 230 260 400Mounting Electrical Power ConnectionsCable Spacers for 200 and 230 a Push Buttons Bypass Time DelayIndicator Lights Transfer TestTo Cancel an Active Exercise Period Clock BatterySettings Generator Starting ContactsTable D. Voltage and Frequency Settings Table C. Time Delay SettingsController Factory Settings --- Summary Remote Control FeaturesBypass load transfer to utility time delay Remote testVoltage Checks Functional TestManual Operation Electrical OperationSequence of Operation --- Utility Failure SeriesTroubleshooting Utility Acceptable lightTroubleshooting Problem Cause and SolutionIndex
Related manuals
Manual 12 pages 21.36 Kb

185 specifications

The Emerson 185 is an advanced and versatile automated control system that stands out for its exceptional performance and reliability in various industrial applications. Designed to streamline operations, improve efficiency, and ensure safety, the Emerson 185 integrates cutting-edge technologies to address the complex demands of modern industries.

One of the main features of the Emerson 185 is its modular architecture, which allows for easy scalability and customization. This flexibility enables operators to adapt the system according to their specific requirements, whether for small-scale processes or large, intricate industrial plants. The modular design simplifies upgrades and maintenance, ensuring that businesses can stay ahead in today's fast-paced environment.

Incorporating advanced control algorithms, the Emerson 185 enhances process automation. Its robust predictive analytics capabilities allow for real-time monitoring and data analysis, which aid in optimizing performance and reducing downtime. With this technology at their disposal, operators can anticipate potential issues and take proactive measures, resulting in improved operational efficiency.

The Emerson 185 is also equipped with user-friendly interfaces that facilitate intuitive operation. Its advanced graphical displays and customizable dashboards provide operators with comprehensive visibility into process performance. This feature allows for informed decision-making and quick responses to unexpected situations, ultimately contributing to increased productivity.

Another significant characteristic of the Emerson 185 is its emphasis on safety and environmental compliance. The system includes built-in safety features and adheres to international standards, ensuring that operations not only meet regulatory requirements but also promote a safer working environment. The emphasis on sustainability aligns with the growing expectation for environmental responsibility in industrial practices.

Communication is a key component of the Emerson 185. The system supports various communication protocols, enabling seamless integration with existing infrastructure and third-party devices. This interoperability ensures that organizations can leverage their current investments while enhancing the overall control capabilities of their processes.

In summary, the Emerson 185 combines modularity, advanced automation, user-friendly interfaces, safety features, and effective communication to deliver a comprehensive solution for modern industrial challenges. Its focus on improving efficiency and ensuring reliability makes it a valuable asset for businesses aiming to optimize their operations and maintain a competitive edge in today's ever-evolving market. With the Emerson 185, organizations can confidently navigate the complexities of modern industrial environments.
Top Page Image Contents