Philips 235P2 Horizontal flicker appears, Image appears blurred, indistinct or too dark, No sound

Page 53

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image appears blurred, indistinct or too dark

•Adjust the contrast and brightness on On-Screen Display.

An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.

•Uninterrupted display of still or static images over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after- imaging", or "ghost imaging" is a well-known phenomenon in monitor panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.

•Always activate a moving screen saver program when you leave your monitor unattended.

•Always activate a periodic screen refresh application if your monitor will display unchanging static content.

•Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.The damage mentioned above is not covered under your warranty.

Image appears distorted.Text is fuzzy or blurred.

•Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.

Green, red, blue, dark, and white dots appears on the screen

•The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.

The "power on" light is too strong and is disturbing

•You can adjust “power on” light using the power LED Setup in OSD main Controls.

Audio problem

No sound

•Check if audio cable is connected to PC and monitor correctly.

•Ensure audio is not muted. Press OSD “Menu”, select “Audio” then “Mute”. Check it on “Off” position.

•Press “Volume” in OSD main control to adjust the volume.

USB problem

USB peripherals are not working

•Check if USB upstream cable is connected to your monitor correctly

•Turn your monitor OFF and ON once again. You may need to install/reinstall USB drivers in your PC and ensure hub is active.

•Reconnect your USB peripherals

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative.

51

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Customer care and warranty Troubleshooting & FAQs Table of Contents Operation Safety precautions and maintenanceTemperature 0-40C 32-95F Humidity 20-80% RH Notational Descriptions Weee Installation Package contents Setting up the monitorConnecting to your PC Main menu Sub menu Display menu Resolution notification Height adjustmentPhysical Function Pivot Tilt SwivelRemove the 4 screw covers Remove the BaseCondition For Vesa standard mounting applications Why do I need it? How to enable SmartImage?Except using key to scroll down, you can also How does it work?Off No optimization by SmartImage What is it? First launch -Wizard Philips SmartControl PremiumPage Page ECO Page OptionAuto Pivot Facoty Preset can also be called from the drop down menu Task Tray Menu Enabled Win No other alternative path available Drag and Drop WindowsOther alternative path Vista Display Tune from the start menu or short cut on the desktop Title Bar OptionsLeft Click Menu Name Description Image SmartDesktop Partition DefinitionsLeft side Vertical Horizontal Split TopRight side Vertical Right side Vertical Even SplitCustom settings Settings Default settingsPixels and Sub pixels Philips Flat Panel Monitors Pixel Defect PolicyTypes of Pixel Defects Bright Dot DefectsModel USB TFT-LCDYES Mtbf Rohs YES Epeat EnvironmentalMaximum Resolution Resolution & Preset ModesAutomatic PowerSaving For 235P2/235PL2Epeat Electronic Product Lead-free ProductTCO Displays 5.0 Information Congratulations Product also comply with the following standards Benefits of Epeat2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive Reorient or relocate the receiving antenna Federal Communications Commission FCC Notice U.S. OnlyFCC Declaration Commission Federale de la CommunicationPaikka/Ilmankierto Polish Center for Testing and Certification NoticeVaroitus Plassering/VentilasjonAchtung Beim Aufstellen Ergonomie Hinweis nur DeutschlandLatin America Eastern EuropeNorth America PacificWhat is excluded? Page Just a click away Just a phone call away Dear CustomerBelarus Estonia Fujitsu Services OUBulgaria Czech RepublicSerbia & Montenegro Romania TurkeyUkraine SlovakiaKediri, Gersik Additional service pointsHong Kong South Africa Service hours Sun.~Thurs After service hours untilTo the service provider at your expense Limited Warranty Computer MonitorWhat is EXCLUDED? WHO is COVERED? What is COVERED?Your warranty does not cover Where can I GET More INFORMATION? To GET Warranty Service in Canada Your International Guarantee Dear Customer No Picture Power LED not lit TroubleshootingNo Picture Power LED is white blinking Screen saysHorizontal flicker appears Power on light is too strong and is disturbingImage appears blurred, indistinct or too dark No soundRun Windows Update and updated monitor and/or video driver SmartControl Premium FAQsPage Q2 What does the recommended refresh rate for monitor? Icm? Q4 How do I adjust the resolution?Press OK to show the OSD On Screen Display menu Q7 How should I clean the monitor surface?Q9 Can the Philips monitor be mounted on the wall? Q10 Can I connect my monitor to any PC, workstation or Mac?
Top Page Image Contents