Philips 220P2ES/00 user manual Troubleshooting, No Picture Power LED not lit, Screen says

Page 46

7 Troubleshooting & FAQs

7.1 Troubleshooting

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.

Common Problems

No Picture (Power LED not lit)

•Make sure the power cord is plugged into the power outlet and into the back of the monitor.

•First, ensure that the power button on the front of the monitor is in the OFF position, then press it to the ON position.

No Picture (Power LED is white blinking)

•Make sure the computer is turned on.

•Make sure the signal cable is properly connected to your computer.

•make sure the monitor cable has no bent pins on the connect side. If yes, repair or replace the cable.

•The Energy Saving feature may be activated

Screen says

•Make sure the monitor cable is properly connected to your computer. (Also refer to the Quick Set-Up Guide).

•Check to see if the monitor cable has bent pins.

•Make sure the computer is turned on.

AUTO button doesn't function

•The auto function is applicable only in VGA- Analog mode. If the result is not satisfactory, you can do manual adjustments via the OSD menu.

Note

The Auto Function is not applicable in DVI-Digital mode as it is not necessary.

Visible signs of smoke or sparks

•Do not perform any troubleshooting steps

•Disconnect the monitor from mains power source immediately for safety

•Contact with Philips customer service representative immediately.

Imaging Problems

Image is not centered

•Adjust the image position using the “Auto” function in OSD Main Controls.

•Adjust the image position using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image vibrates on the screen

•Check that the signal cable is properly securely connected to the graphics board or PC.

Vertical flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

44

Page 45 Page 47
Image 46
Page 45 Page 47
Contents 220P2 Table of Contents Temperature 0-40C 32-95F Humidity 20-80% RH Safety precautions and maintenanceOperation Notational Descriptions Weee Setting up the monitor Installation Package contentsTo switch monitor’s power on and off Basic and simple instruction on the control keys Main menu Sub menuSwivel Zero power switch Resolution notificationHeight adjustment PivotExtend the monitor base to its maximum height Except using key to scroll down, you can also Why do I need it?How does it work? Off No optimization by SmartImage What is it? Philips SmartControl Premium First launch -WizardStart with Standard pane Adjust menu Page ECO Page OptionAuto Pivot Facoty Preset can also be called from the drop down menu Task Tray Menu Enabled Pixels and Sub pixels Philips Flat Panel Monitors Pixel Defect PolicyTypes of Pixel Defects Model YES TFT-LCDCcfl USBMtbf Environmental Rohs YES EpeatAutomatic PowerSaving Power Management DefinitionLead-free Product Epeat Electronic Product2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive Benefits of EpeatEN61000-3-22006 Limits for Harmonic Current Emission Product also comply with the following standardsFederal Communications Commission FCC Notice U.S. Only Reorient or relocate the receiving antennaCommission Federale de la Communication FCC DeclarationVaroitus Polish Center for Testing and Certification NoticePaikka/Ilmankierto Plassering/VentilasjonErgonomie Hinweis nur Deutschland Achtung Beim AufstellenNorth America Eastern EuropeLatin America PacificWhat is excluded? Page Dear Customer Just a click away Just a phone call awayBulgaria Estonia Fujitsu Services OUBelarus Czech RepublicUkraine Romania TurkeySerbia & Montenegro SlovakiaCompany Name PT. Gadingsari elektronika Prima Africa South AfricaPage Your warranty does not cover WHO is COVERED? What is COVERED?What is EXCLUDED? Where can I GET More INFORMATION?To GET Warranty Service in Canada Your International Guarantee Dear Customer No Picture Power LED not lit TroubleshootingScreen says Power on light is too strong and is Disturbing Reconnect your USB peripheralsSmartControl Premium FAQs Page Page Q7 How should I clean the LCD surface? Q9 Can the Philips LCD Monitor be mounted on the wall?
Top Page Image Contents