Philips 220P2 Power on light is too strong and is Disturbing, Reconnect your USB peripherals

Page 47

Horizontal flicker appears

•Adjust the image using the “Auto” function in OSD Main Controls.

•Eliminate the vertical bars using the Phase/ Clock of Setup in OSD Main Controls. It is valid only in VGA mode.

Image appears blurred, indistinct or too dark

•Adjust the contrast and brightness on On- Screen Display.

An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.

•Uninterrupted display of still or static images over an extended period may cause " burn in", also known as "after-imaging " or "ghost imaging", on your screen. "Burn-in", "after- imaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "after-imaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off.

•Always activate a moving screen saver program when you leave your monitor unattended.

•Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content.

•Severe” burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.The damage mentioned above is not covered under your warranty.

Image appears distorted.Text is fuzzy or blurred.

•Set the PC’s display resolution to the same mode as monitor’s recommended screen native resolution.

Green, red, blue, dark, and white dots appears on the screen

•The remaining dots are normal characteristic of the liquid crystal used in today’s technology, Please refer the pixel policy for more detail.

The "power on" light is too strong and is

disturbing

•You can adjust “power on” light using the power LED Setup in OSD main Controls.

Audio problem

No sound

•Check if audio cable is connected to PC and monitor correctly.

•Ensure audio is not muted. Press OSD “Menu”, select “Audio” then “Mute”. Check it on “Off” position.

•Press “Volume” in OSD main control to adjust the volume.

USB problem

USB peripherals are not working

•Check if USB upstream cable is connected to your monitor correctly

•Turn your monitor OFF and ON once again. You may need to install/reinstall USB drivers in your PC and ensure hub is active.

•Reconnect your USB peripherals

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative.

45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents 220P2 Table of Contents Operation Safety precautions and maintenanceTemperature 0-40C 32-95F Humidity 20-80% RH Notational Descriptions Weee Installation Package contents Setting up the monitorTo switch monitor’s power on and off Main menu Sub menu Basic and simple instruction on the control keysPivot Resolution notificationHeight adjustment Swivel Zero power switchExtend the monitor base to its maximum height How does it work? Why do I need it?Except using key to scroll down, you can also Off No optimization by SmartImage What is it? First launch -Wizard Philips SmartControl PremiumStart with Standard pane Adjust menu Page ECO Page OptionAuto Pivot Facoty Preset can also be called from the drop down menu Task Tray Menu Enabled Types of Pixel Defects Philips Flat Panel Monitors Pixel Defect PolicyPixels and Sub pixels Model USB TFT-LCDCcfl YESMtbf Rohs YES Epeat EnvironmentalPower Management Definition Automatic PowerSavingEpeat Electronic Product Lead-free ProductProduct also comply with the following standards Benefits of EpeatEN61000-3-22006 Limits for Harmonic Current Emission 2006/95/EC Low Voltage Directive 2004/108/EC EMC DirectiveReorient or relocate the receiving antenna Federal Communications Commission FCC Notice U.S. OnlyFCC Declaration Commission Federale de la CommunicationPlassering/Ventilasjon Polish Center for Testing and Certification NoticePaikka/Ilmankierto VaroitusAchtung Beim Aufstellen Ergonomie Hinweis nur DeutschlandPacific Eastern EuropeLatin America North AmericaWhat is excluded? Page Just a click away Just a phone call away Dear CustomerCzech Republic Estonia Fujitsu Services OUBelarus BulgariaSlovakia Romania TurkeySerbia & Montenegro UkraineCompany Name PT. Gadingsari elektronika Prima South Africa AfricaPage Where can I GET More INFORMATION? WHO is COVERED? What is COVERED?What is EXCLUDED? Your warranty does not coverTo GET Warranty Service in Canada Your International Guarantee Dear Customer Screen says TroubleshootingNo Picture Power LED not lit Reconnect your USB peripherals Power on light is too strong and is DisturbingSmartControl Premium FAQs Page Page Q9 Can the Philips LCD Monitor be mounted on the wall? Q7 How should I clean the LCD surface?
Top Page Image Contents