Philips 150DM Ergonomie Hinweis nur Deutschland, End-of-Life Disposal, Information for UK only

Page 25

47APPENDIX

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PIS- TORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

Ergonomie Hinweis (nur Deutschland)

Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften.

Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III 5 Abs. 4 der Röntgenverordnung erfüllt sind.

Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß

Reparaturen nur durch Fachpersonal durchgeführt werden. nur original-Ersatzteile verwendet werden.

bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird.

Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge).

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger.

!ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECK- ER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.

End-of-Life Disposal

Your new monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.

APPENDIX 48

Information for UK only

WARNING — THIS APPLIANCE MUST BE EARTHED.

Important:

 

 

This apparatus is supplied with an approved moulded 13A

 

B

plug.To change a fuse in this type of plug proceed as follows:

 

 

 

A

 

1

Remove fuse cover and fuse.

 

2

Fit new fuse which should be a BS 1362 5A,A.S.T.A. or

 

 

BSI approved type.

3Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribu- tion board should not be greater than 5A.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (“E”)

1The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the

letter “E” or by the Earth symbol or coloured GREEN or GREEN AND YELLOW.

2 The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured

BLACK.

3The BROWN wire must be connected to the terminal which marked with the letter “L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires.

Image 25
Contents User’s Manual About This Manual Getting Started 3 BeforeYou Begin Complete Start Guide 7 Hardware SetupPrerequisites BeforeYou BeginUnpacking Physical Appearance Cable Setup Installing Windows XP Service PackLoad Battery Additional Hardware SetupSmart Display Services Setup Software SetupConnect USB Cables screen Smart Display Setup WizardUse Existing Wireless Hardware? Computers you want to access through DesXcape 150DMView and Print Network Settings When you have printed this page, click Next to continueDetach from Base Station First-timer TutorialOn-Screen Tutorial Disconnect from your computer Connect to your computerPlace back into base station Click on the user name with which you want to connectProduct Care DesXcape 150DM software updateDesXcape Experience Online RegistrationAutomatic wireless reconnection DesXcape 150DM as Wireless MonitorBattery and Power status VGA Out from DesXcape 150DMDesXcape 150DM as Desktop Monitor Working with an optional wireless keyboardOther DesXcape 150DM functions Optimize and CustomizeSound settings on your DesXcape 150DM Power-saving settings on your DesXcape 150DMReconfigure the DesXcape 150DM wireless network Access to multiple computersOSD Tree For Analog /Digital Input OSD functionsGlossary Wired equivalent privacy WEP Windows Powered Smart DisplayWireless access point Wireless local area network WlanDuring Hardware Setup Before SetupDuring Software Setup Q10What does it mean to SelectYour Wireless Network? Q9 What does Use Existing Wireless Hardware mean?During Use Q13I see a Check Cable Connection screenIntroduction to DesXcape 150DM What is DesXcape 150DMSmart Display vs. DesXcape 150DM Wireless Communications SpecificationsHow DesXcape 150DM works Embedded SystemWarranty Regulatory information Additional information & customer carePlace no heavy objects on the screen CE Declaration of ConformityEnergy Star Declaration EN61000-3-3 EN300328-2/EN301489-17Philips Ergonomie Hinweis nur Deutschland How to connect a plugEnd-of-Life Disposal Information for UK onlyPhilips LCD Panel Pixel Defect Policy CopyrightBright Dot Dark DotProtect Your Investment Open Please Warranty