Philips BDL3215E, BDL4225E user manual Setup Procedure

Page 17

User Manual BDL3215E / BDL4225E

Setup Procedure

1. Install the system on the right location

CAUTION:

‡ THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. (For 42” only)

Failure to follow this caution may result in injury if the LCD monitor falls.

‡ DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF.

7KH/&'GLVSOD\PXVWEHLQVWDOOHGE\DTXDOLÀHGWHFKQLFLDQ Contact your dealer for more information.

‡ DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP, OR FACE DOWN.

‡ DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT.

Failure to follow this caution will result in display defects.

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by 1.5V AAA batteries. To install or replace batteries:

1.Press and slide to open the cover.

2.Align the batteries according to the (+) and (–) indications inside the case.

3.Replace the cover.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.

‡ Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.

‡ 'RQRWPL[EDWWHU\W\SHV

‡ Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries.

‡ 5HPRYHGHDGEDWWHULHVLPPHGLDWHO\WRSUHYHQWEDWWHU\OLTXLG from leaking into the battery compartment. Don’t touch H[SRVHGEDWWHU\DFLGLWFDXVHGDPDJHWR\RXUVNLQ

NOTE:

If you do not intend to use the Remote Control for a long period, remove the batteries.

3. Connect to external equipment

‡ 7RSURWHFWWKHFRQQHFWHGHTXLSPHQWWXUQRIIWKHPDLQSRZHU before making connections.

‡ Please refer to section “Connectivity” P.17~P.21 for operations.

4. Connect power cord

‡ The power outlet socket should be installed as near to the

HTXLSPHQWDVSRVVLEOHDQGVKRXOGEHHDVLO\DFFHVVLEOH

‡ Fully insert the prongs into the power outlet socket. Loose connection may cause noise.

NOTE:

Please refer to “SAFETY INSTRUCTIONS” section of this manual for proper selection of AC power cord.

5.Turn on the power of the attached external equipment

When connected with a computer, turn the computer power RQÀUVW

6. Operate the attached external equipment

'LVSOD\WKHVLJQDOIURPWKHH[WHUQDOHTXLSPHQW

7. Adjust the sound

0DNHDGMXVWPHQWVWRGHFUHDVHRULQFUHDVHYROXPHLIUHTXLUHG

8.Adjust the screen

0DNHDGMXVWPHQWVWRWKHGLVSOD\SRVLWLRQRUVHWWLQJVLIUHTXLUHG

9. Adjust the image

0DNHDGMXVWPHQWVRIEULJKWQHVVRUFRQWUDVWLIUHTXLUHG

10.Recommended Adjustment

To reduce the risk of “image persistence”, please adjust the following items based on the application being used:

“POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”, “SCHEDULE”.

14

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Public Signage Solutions Page Table of Contents Safety Instructions Regulatory Information CE Declaration of Conformity Polish Center for Testing and Certification Notice Information for UK only How to connect a plug10 For customers in Canada and U.S.A North Europe Nordic Countries InformationContents Control Panel Elements Name and FunctionsTerminal Panel  Video in connector BNC To input composite S-VIDEO in connector Mini DIN 4 pin To input Remote Control Handling the remote control Operating Range for the Remote ControlUpright position How to remove the table stand How to mount or attach table stand to the LCD MonitorHow to install table stand Ventilation Requirements for enclosure locating Way II Mount the monitor on the wallSetup Procedure To prevent the main power switch from being changed How to Use the Logo Guider for Portrait Mode? Install the LCD Monitor in Portrait ModeHow to Remove the Logo for landscape mode? Before making connections Connectivity DiagramConnectivity Connecting the LCD Monitor to a Personal Computer Connecting to a Personal ComputerConnect the LCD Monitor to a Computer with a Digital Output Connecting to a Digital Interface EquipmentConnect the LCD Monitor to a DVD Player Connecting to a DVD PlayerRQQHFWWKH/&0RQLWRUWRD6WHUHR$PSOLÀHU RQQHFWLQJWRD6WHUHR$PSOLÀHUPressing the Main Power Switch Power on and OFF ModesPressing the power button Using the remote controlUsing Power Management Power IndicatorDisplay Signal of Video Source Setting to Video Picture SizeAudio Source Switching Smart Picture ModeControl Lock Mode OSD InformationOSD screen OSD On-Screen-Display ControlsPicture Picture Reset Color TemperatureTint ColorZoom Mode Clock PhaseScreen PositionCustom Zoom Screen ResetAudio Audio ResetBalance TreblePIP Picture in Picture PIP ResetPIP Size PIP AudioConfiguration Factory Reset Configuration ResetOSD Turn OFF Sleep TimerInformation OSD OSD H PositionMonitor Information BNC Video ModeAdvanced Option Tiling IR ControlDate and Time ScheduleMonitor ID Smart PowerAdvanced Option Reset Recommendations Image PersistenceImage Sticking of LCD Panel Video VGA BNC Remote control numbering functionPixels and Sub-pixels Pixel defect policyDark Dot Defects Troubleshooting Stripe Noise SCHEDULE/SLEEP Timer function is not working properlyNo Signal is displayed on the screen Output Signal Input SignalPower Supply DimensionPower consumption Power ManagementComplied Regulatory and Guidelines Plug & PlayVesa Compatible arm mounting interface Operational EnvironMent Normal on 215W typical, 220W max Standby 1W, standby mode Pin Assignment 6SHFLÀFDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH
Top Page Image Contents