Xerox 1235 manual Physical and Chemical Properties

Page 76

Specifications

XEROX EXPOSURE LIMIT (XEL): 2.5 mg/m3 (total dust); 0.4 mg/m3 (respirable dust)

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE/ODOR: Black, blue, red, or yellow powders/faint odor

BOILING POINT: Not applicable

SOLUBILITY IN WATER: Insoluble

EVAPORATION RATE: Not applicable

VAPOR DENSITY (Air = 1): Not applicable

VOLATILE: Not applicable

SOFTENING RANGE: 110-140 degrees F (43-60 degrees C)

MELTING POINT: Not available

SPECIFIC GRAVITY (Water = 1): Approximately 1

VAPOR PRESSURE (mm Hg): Not applicable

pH: Not applicable

SECTION 10 - STABILITY AND REACTIVITY

STABILITY: Stable.

INCOMPATIBILITY WITH OTHER MATERIALS: Strong oxidizers

HAZARDOUS POLYMERIZATION: Will not occur

HAZARDOUS DECOMPOSITION PRODUCTS: During a fire, toxic gases may be generated by thermal decomposition or combustion.

SECTION 11 - TOXICOLOGICAL INFORMATION

This material has been evaluated by Xerox Corporation. The toxicity data noted below is based on test results of similar toners.

Oral LD50: > 5 g/kg (rats), practically non-toxic

Dermal LD50: > 5 g/kg (rabbits), practically non-toxic

Inhalation LC50: > 5 mg/l (rats; 4 hour exposure), practically non-toxic

Inhalation LD50: > 20 mg/l (rats; calculated for 1 hour exposure), non-toxic per

DOT

Eye Irritation: Non-irritating (rabbits)

Skin sensitization: Non-irritating (rabbits; human patch)

Human Patch: Non-irritating, non-sensitizing

Mutagenicity: No mutagenicity detected in Ames assay

Carcinogens: None present

Additional Information: The results obtained from a Xerox-sponsored Chronic Toner Inhalation Study demonstrated no lung changes in rats for the lowest (1 mg/m3) exposure level (i.e., the level most relevant to potential human exposure). A very slight degree of fibrosis was noted in 25 percent of the animals at the middle (4 mg/m3) exposure level, while a slight degree of fibrosis was noted in all the animals at the highest (16 mg/m3) exposure level. The findings are attributed to lung overloading, a generic response to excessive

60	Phaser 1235 Color Printer

Image 76

Contents L O R P R I N T E R Page Phaser 1235 Color Printer User Guide Page Page Warranty Printer WarrantyConsumables Warranty Page User safety summary Electrical SafetyMaintenance Safety 51 kg 113 lbs Do not open the covers while printing Symbols as marked on product Page Contents Xiv Xerox Supplies and Accessories Toner Cartridges Imaging drums Fuser Transfer beltCustomer-Replaceable Consumables CRCs Part NumberImaging Drums Transfer Belt Transfer Belt 001R00559Customer Replaceable Units CRUs SuppliesPaper Feed Roller Kit 600K89320 Size Description Part NumberXerox Phaser Transparency Sleeves and Pockets Description Part NumberFeatures Part Number AccessoriesPaper Capacity Part Number Features Part Number Ergonomic surface height Additional MemoryFront Panel Usage Front Panel LayoutBasic Menu Navigation Menu NameFront Panel Printing the Menu Map Print MenuPrint Modes DraftNormal High QualityColor Modes Advanced Color ModesPhosphor settings Black OverprintProcess Grayscale Unspecified RGBPaper Tips Paper Tips Supported page sizes and print area Monarch Envelope#10 Envelope C5 EnvelopeUniversal Tray Paper SpecificsTransparency Specifics Universal Tray Loading Tray 1, 2, or 0730-27 Menu Media Type Weight Media Specifics Multi-Sheet Bypass Feeder MBFSupported Media Capacity Loading the Multi-Sheet Bypass Feeder MBF Media Types Weight Select Multi-Sheet Bypass Feeder MBF as Paper Source Xerox Phaser 35 Series Transparencies Envelopes Select Multi-Sheet Bypass Feeder MBF as Paper Source Guidelines for envelope printing 0730-34 Select Multi-Sheet Bypass Feeder MBF as Paper Source Automatic 2-Sided Printing From the Paper Tray 0730-36 0730-37 Manual 2-Sided Printing Printing Side From a traySided Prints 0730-43 Sided Prints Troubleshooting Print Quality Problems Print Quality Problem Common Causes Potential RemediesDark Vertical Lines Only one color, anRepeating Defects Back-Side Contamination Preventing media jams Clearing Paper/Media JamsWhat causes a media jam? Clearing Media Jams Area a Jam 0730-54 Remove the jammed media from the transfer belt area Replace the toner cartridges/imaging drum assembly Area B Jam Remove the Universal Tray from the printer Printer CD-ROM Getting HelpXerox web site Other online services InfoSMART Knowledge BaseColor Connection To find a local resellerCustomer Support Center AseanSpecifications Material Safety Data Sheets Color Toner CartridgesProduct Use Xerox Phaser 1235 Color Printers Ingredients percent by weight CAS numberImmediate Effects Chronic Effects None knownPhysical and Chemical Properties Ecological Information Material Safety Data Sheets CleanTex Alcopad Product IdentificationEvaporation Rate Butyl ACETATE-1 Vapor Density AIR = 1 Ecological InformationSara Title III Reporting Other Information Specifications Index Phaser 1235 Color Printer User Guide Phaser 1235 Color Printer Page Printed on recycled paper