Winegard MV3500T, MV3535T, WI3535T, MVT-35W Installing the Dome, Installing the Power Switch

Page 6

Installation

GPS installation —

10.The GPS antenna is pre-wired and has a 1 meter cable running through one of the connectors.

Determine location for GPS antenna. It is recom- mended you place the GPS antenna 3 feet from dome and away from any other obstruction.

The recommended location for the GPS antenna is based on having a level location and a clear view of the sky for the best satellite signal acquisition. Do not secure GPS antenna to roof at this time.

IMPORTANT! The GPS must be located minimum of 3 feet away from obstructions on roof of vehicle. An- tenna must have a clear view of the sky for proper operation.

!NICKS OR CUTS IN WIRING JACKET MAY CAUSE WATER TO LEAK INTO VEHICLE.

Cable entry installation —

1.Decide the best location for the cables to enter the vehicle, and the location of the power switch and receiver (see “Installing the switch and receiver”on pages 9 and 10). Drill a 1/2” hole in the roof, push wires inside. Make proper connections. You must have filtered +12 VDC power source.

2.Place cable-entry plate over hole and cables. Screw in place. Seal plate and screw holes with ap- proved sealant (not included).

3.Depending on the length of the cable on the roof, you may need to use cable clamps or wire ties (not provided) between the unit and your cable-entry plate. Clamping the cable every 12”-16” should eliminate any unnecessary cable movement, Figure 6.

FIGURE 6

CABLE- CABLE

ENTRY CLAMPS

INSTALLING THE DOME

BEFORE INSTALLING THE DOME, verify that

!switches are set to your satellite provider. (See page 2.)

INSTALLING THE POWER SWITCH

1.Choose a location to install the MV3500T power ON/OFF switch. Remember when selecting a location that you will need to run the +12VDC power cable from the MV3500T to the switch. Be sure the switch is in the OFF position before continuing. See Figure 7 page 9.

Wall or panel mount: Drill 1-1/4” hole, pull wires through wall or panel.

Surface mount: Determine location and direction of box. Mount box and feed wire into one of the box open ings. Snap the rocker switch into the switch plate. Be sure switch is off!

2.Connect the ground wire from the vehicle and the BLACK ground wire from the MV3500T together, using large yellow flag connector.

3.Connect the YELLOW flag connector to the silver spade on the switch.

4.Connect the RED wire from the MV unit to the small RED flag connector.

5.Connect small RED flag connector to center spade on switch.

6.Connect the +12 V power wire from the vehicle to a small RED flag connector.

7.Connect small RED flag connect to isolated spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

FIGURE 7

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

Insert screw in holes on dome rim. Be sure bolt is vertical; not tilted to side. Tighten to

20in.-lb., or approximately until washer is visible around screw head.

CAUTION:

DO NOT

OVERTIGHTEN!!

QUADREX SCREW WITH RUBBER WASHER (USE #2

PHILLIPS)

STEPS 2 & 3

STEPS 6 &7

TWO GROUND WIRES

+12 V FROM VEHICLE

1 FROM VEHICLE

 

1 BLACK WIRE FROM

 

SATELLITE DISH

STEPS 4 & 5

 

 

RED POWER

 

WIRE FROM

 

DISH

REV. 12/05

6

Image 6
Contents Winegard Parts Included Parts Included Tools Needed How to UnpackTools Needed for Unpacking & Installation Unpacking the UnitInstallation Diagram Lnbf GPS CableTo Change Switches Inside Dome Quick Reference GuideInstallation Installing unit on roof of vehicleInstalling the Dome Installing the Power SwitchInstallation Wiring Connecting one receiverDirectv programming Troubleshooting Problem SolutionFeatures and specifications Page Return Authorization Policy
Related manuals
Manual 8 pages 7.71 Kb Manual 3 pages 10.38 Kb

MVT-35B, MVT-35W, WI3535T, MV3500T, MV3535T specifications

The Winegard MV3500T, MV3535T, MVT-35B, MVT-35W, and WI3535T are some of the most advanced and versatile over-the-air TV antennas available today. Designed for both urban and rural environments, these antennas offer exceptional reception capabilities and a range of features that cater to diverse viewing needs.

The MV3500T is a compact, high-performance antenna that integrates advanced technology to ensure reliable reception of digital TV signals. Its sleek design allows for easy installation on rooftops or walls, and its lightweight construction means it can be mounted without the need for heavy-duty support. The MV3500T is engineered to receive UHF and VHF signals, making it suitable for a broad spectrum of broadcast channels.

The MV3535T is a step up, featuring a larger element size that enhances its reception capabilities. This model is particularly beneficial for users living in areas farther away from broadcasting towers. The MV3535T's multi-directional reception technology ensures that users can receive signals from multiple directions without having to constantly adjust the antenna’s position.

For those who prioritize flexibility in installation, the MVT-35B and MVT-35W models stand out. These antennas are designed for portable use, which makes them perfect for RVs, boats, and tailgating. The MVT-35B features a black finish, while the MVT-35W comes in white, allowing users to choose a model that best matches their aesthetic preferences. Both models benefit from Winegard’s patented dual-band technology, ensuring robust signal reception in fluctuating weather conditions.

Lastly, the WI3535T is notable for its smart technology integration. This antenna comes equipped with a built-in preamplifier that enhances weak signals, making it easier to pick up channels that might otherwise be missed. The WI3535T is designed with a weather-resistant casing, ensuring durability and longevity even when exposed to harsh environmental conditions.

In summary, the Winegard MV series antennas exemplify cutting-edge technology with features tailored for optimal performance. Whether users are seeking a stationary solution or a portable antenna for on-the-go viewing, models like the MV3500T, MV3535T, MVT-35B, MVT-35W, and WI3535T provide the necessary versatility and reliability for enjoying high-quality over-the-air television programming. With these antennas, Winegard continues to set the standard for innovative reception solutions in the industry.