Star Micronics TSP400Z user manual Power + on Line + Feed switches

Page 14

ENGLISH

Pause at a: HEX dump

 

 

Pause at b: sensor selection

 

 

Press ON LINE

1 short beep

Reflecting sensor

Press FEED

2 short beeps

Transmissive sensor

Pause at c: command mode selection

 

Press ON LINE

1 short beep

Page mode

Press FEED

2 short beeps

Line mode

3) Power + ON LINE + FEED switches

(Turn the power on while holding the ON LINE and FEED switches depressed.)

Approx.

Approx.

Approx.

Approx.

 

2 sec.

 

2 sec.

2 sec.

 

2 sec.

1 short beep

… 2 short beeps

 

… 3 short beeps

… 1 long beep

 

a

 

b

c

 

d

e

HEAD UP

NO PAPER

ERROR

 

LEDs flash

All LEDs

LED

LED

 

LED

 

successively

light up

lights up

lights up

 

lights up

 

lights up

 

Pause at a: RAM backup cleared

 

 

 

 

Pause at b: feed function selection

 

 

 

 

 

Press ON LINE

1 short beep

Top of Form disabled.

 

Press FEED

 

2 short beeps

Top of form enabled.

Pause at c: sensor adjustment mode

Pause at d: no operation

Pause at e: clearing of all memory switches and test print

1At e, release the ON LINE switch and FEED switch in 2 seconds or less (all LEDs go off).

2Press the ON LINE switch and FEED switch in 2 seconds or less,

and hold them depressed for at least 3 seconds (all LEDs light up).

3Release the ON LINE switch and FEED switch.

4The contents of all memory switches will be erased (all will be set to 0).

After that, test print is carried out.

*If this process is interrupted midway, the printer will operate in regular mode.

*After the memory switch settings are erased, the memory switches must be set again, as appropriate for each model.

– 11 –

Image 14
Contents TSP400Z Series EC Council Directive 89/336/EEC of 3 May Table of Contents Handling Notes Unpacking and inspectionUnpacking TSP442Z TSP412ZFerrite core installation *Europe only Parallel interfacePeripheral unit cable Connecting the interface cable Serial interfaceSetting up Loading the Paper RollTemporarily place the paper roll on Adjusting the Head Position Control panel Basic OperationPower switch and on LINE/FEED switch combinations Head UP indicatorPower + on Line + Feed switches Print Density Adjustment Sensor Adjustment ModeEnglish Errors Error Cause BuzzerOther errors only in page mode Buzzer Sounding VariationsTable DES Matieres Remarques sur la manipulation Deballage et inspectionDéballage Identification des pieces et nomenclature Installation du tore de ferrite *Europe uniquement Interface parallèleCâble de périphérique Raccordement du câble d’interface Interface sérieInstallation Chargement du rouleau de papierRouleau de papier Barre de déclenchement Réglage de la position de la tête Faire retourner la tête d’impression enCommutateur/Témoin on Line EN Ligne Tableau de commandeFonctionnement de base Commutateur Feed AvanceTémoin manque papier Témoin Power AlimentationTémoin Head UP Tete Vers LE Haut Témoin d’erreurInterrupteur d’alimentation + commutateurs on Line + Feed Mode d’ajustement de capteur Réglage de la densité d’impressionFrench Erreurs réparables Autres erreurs seulement en modeErreurs Erreurs non réparablesVariations de tonalité de l’avertisseur sonore Inhaltsverzeichnis Hinweise Auspacken und KontrolleAuspacken AbbFunktion und Bezeichnung der einzelnen Bauteile Installation der Ferritkerne *Nur Europa Parallele SchnittstellePeripheriegerätkabel Anschluss des Schnittstellenkabels Serielle SchnittstelleInbetriebnahme Einlegen der PapierrolleDarauf, daß die Rolle zum Einlegen Einstellung der Druckkopfposition Abb Schalter/Anzeige on Line BedienfeldGrundlegender Betrieb Schalter FeedKein-Papier-Anzeige Anzeige PowerAnzeige Head UP FehleranzeigeNetzschalter + Schalter on Line + Schalter Feed Einstellung der Druckdichte SensoreinstellmodusDeutsch Nicht behebbare Fehler FehlerBehebbare Fehler Summertonvariationen Sonstige Fehler nur im SeitenmodusIndice Avvertenze Apertura e controllo della confezioneApertura della confezione Identificazione e nomenclatura delle parti Installazione degli anelli di ferrite *Solo europa Interfaccia parallelaCavo dell’unità periferica Collegamento del cavo d’interfaccia Interfaccia serialeInstallazione Caricamento del rotolo di cartaBarra di strappo Regolazione della posizione della testina Pulsante/spia on Line Pannello di controlloOperazioni di base Pulsante FeedSpia Head UP Spia PowerSpia di errore Spia di esaurimento carta3Interruttori accensione + on Line + Feed Regolazione della densità di stampa Modalità di regolazione del sensoreItaliano Errori irrimediabili ErroriErrori rimediabili Altri errori Solo in modalità PaginaVariazione del suono del cicalino Appendix a Specifications General SpecificationsPaper Specifications Print area Appendix Appendix B Dip switch setting Switch Setting BaudAppendix C Serial interface Connectors and Signal Names Serial InterfacePin No Signal name FunctionInterface Connections Table of Connection Signals for Each Mode Appendix D Parallel interfaceCompatible with Amphenol Cable specifications for peripheral unit Appendix E Peripheral unit drive circuitDrive circuit Recommended drive circuit is shown below Appendix F Memory Switch Settings Head Office Overseas Subsidiary Companies

TSP400Z specifications

The Star Micronics TSP400Z is a high-performance thermal receipt printer designed to meet the demands of retail and hospitality environments. Not only does it deliver high-speed printing, but it also integrates a wide array of features that enhance its functionality, making it a preferred choice for businesses seeking reliability and efficiency.

One of the standout features of the TSP400Z is its fast printing speed, capable of reaching up to 250 mm per second. This impressive speed ensures that customer transactions are processed swiftly, thus improving service efficiency and reducing wait times at points of sale. The printer supports a print resolution of 203 DPI, ensuring crisp and clear text as well as high-quality graphics.

The TSP400Z employs advanced thermal printing technology, eliminating the need for ink or ribbons. This not only cuts down on maintenance costs but also ensures a cleaner working environment by reducing waste. The printer is designed for durability and longevity, with a robust construction that withstands the rigors of daily use in busy commercial settings.

Connectivity options are another highlight of the TSP400Z. It supports multiple interfaces, including USB, Serial, and Ethernet, catering to a variety of system configurations. Additionally, it supports Bluetooth connectivity, making it suitable for mobile printing applications. This versatility allows businesses to easily integrate the printer with existing systems and devices.

Another notable characteristic is its ability to print in multiple languages and support various barcode formats. This feature is particularly useful for businesses with a diverse clientele or for those that operate in multiple regions. The printer also includes practical features such as autocutter functionality, ensuring clean and professional receipt cuts, which enhances the overall customer experience.

The TSP400Z is designed with several user-friendly features such as an intuitive control panel, which simplifies operation and troubleshooting. Furthermore, it supports Star’s CloudPRNT technology, allowing for seamless cloud-based printing solutions, which is increasingly becoming essential in modern business practices.

In summary, the Star Micronics TSP400Z is a reliable, efficient, and versatile thermal receipt printer, perfectly suited for retail and hospitality. With its high-speed printing, multiple connectivity options, and advanced features, it is engineered to enhance operational efficiency and customer satisfaction in any busy commercial setting.