Star Micronics XR-1020 Loading Single Sheets, Loading the paper without optional accessories

Page 44

LOADING SINGLE SHEETS

This section will take you through the procedures for loading single sheets of paper.

Loading the paper without optional accessories

If you are using the optional Automatic Sheet Feeder, refer to next section.

1.Place the paper guide in position by inserting the tabs, located on the bottom of the assembly, into the slots on the rear cover of the printer.

Paper guide

-

-

-

Figum d-12.Mounting the paper guide for single sheets.

V

 

2.Adjust the paper guides to match the size of the paper you will be using. Remember that printing will start some distance from the left-hand edge of the carriage.

3.Turn on the power using the switch located at the front of the printer. The printer will beep, indicating that there is no paper in position for printing. The PAPER indicator will also illuminate to confirm this.

4.Make sure that the release lever is at front position.

If fanfold paper is already mounted in the printer, press the aET’EJECf 1 button to park the paper in the off-line state, then move the release lever forward.

36

--

-.

-

-

Page 43 Page 45
Image 44
Page 43 Page 45
Contents XR-1020 XR-1520 Federal CommunicationsCommission HOW to USE this Manual Reference Contents On Line button Printer Control Commands Index Features of the Printer ChapterPrinter Components Page Font Style Example Tms Romn 0123456789ABCDEFGHIJKLMabcdefghijklmSetting UP the Printer Locating the PrinterUnpacking and Inspection Page Setting UP Mounting the platen knobInstall the ribbon cartridge Connecting the interface cable Figure Z-4. Installing the ribbon cartridgeFigurn 2-6. Move the clips until you hear a did Memo Automatic Sheet Feeder Single- Bin a utoma tic Sheet FeederPage 33. Attach the stacker to the Automatic Sheet Feeder Gum 3-S Close he front cover Figum 3-7. insert the stacker attachments Dual-Bin Automatic Sheet Feeder SF- 1ORMWI5RMIIPage Pull Tractor Unit PT-1OXM/15XM Above when removing the FWl Tractor Unit Interface Cartridges DIP Switch Functions on The Serial Interface Cartridge Iz-+EMemo Paper Installationand USE Selection of PaperAdjusting the Printing GAP Shows the recommended print area for each type of papersLoading Fanfold Forms Loading the paper from the rear of the printer Push feed Tractor cover Loading the paper from the bottom of the printer Loading the paper with Push/Pull feed 1button. The paper will be fed past the print Page Paper parking Paper unparking Loading the paper without optional accessories Loading Single SheetsFigutu 4-13.Loading a single sheet Loading the paper with optional Automatic Sheet Feeder Paper loading lever Single-Bin Paper loading leve Eswre bar lever Single-Bin Chapter On Line button Paper Feed buttonSET/EJECT/PARK button Pitch buttonMode button Font buttonShort test mode POWER-UP FunctionsLong test mode Print area test mode Pitch lock modeFont lock mode Pitch and Font lock modeHexadecimal dump Figurn 5-S SamplehexadecimaldumpCoding for IBM-PC with color adapter Switch Combination Functions Top of formChanging the auto loading value Forward micro-feedReverse micro-feed Clearing the buffer/AI/ reset Selecting the print colorSelecting the ASF bin number Store Macro Definition Setting UP Memory Switches Linmenu Print current settings EnweInstallation menu Command menuFont menu Print menu Paper menu Factory settings DOT Adjustment Mode To exit from this mode, press Button Printer Control Commands Select NL Q characters Select draft pica charactersSelect draft elite characters Select italic characters Se/ect NLQ fontSelect font Select upright characters Mode Ascii Cancel emphasized printingSelect NLQ italic characters HlodeI Ascii Emphasized printingCancel double-s trike printing Start underliningStop underlining Star? 0 verliningSubscript Cancel superscript or subscriptSuperscript Select standard character set Select IBM character setSelect character set #I Select character set #2Select international Character set Select IBM codeEnable printing of all character codes Enable printing of all character codes on next CharacterSelect slash zero Select normal zeroCancel condensed printing Pica pitchElite pitch Condensed printingCancel expanded printing Cancel one-line expanded printingExpanded printing Expanded printing for one lineIncrease character spacing Select master print modeSelect fixed spacing Print double-height characters Select double or quadruple sizeSelect character size Return to normal height Select character height, width, and line spacing -’Set line spacing to l/8 inch Set line spacing to 7/72 inchSet line spacing to l/6 inch Set line spacing to n/216 inchSet line spacing to nfl2 inch Execute ES6Line feed Reverse line feedPerform one n/216=inchline feed Perform one n/216=inchreverse line feedFeed paper n lines Set top of page at current positionCancel bottom margin Set page length to n linesSet page length to n inches Set bottom marginDisable paper-out detector Enable paper-out detectorReturn to top of current Set vertical tab stopsSet vertical tab stops every n lines Select vertical tab channelVertical tab Set vertical tab stops in channelSet right margin Horizontal Position CommandsSet left margin Cancel automatic line feed Set left and right marginsCarriage return Set automatic line feedLeft justify Center textRight justify Full justifyReset all tab stops Set horizontal tab stopsSet horizontal tab stop every n columns Horizontal tabAbsolute horizontal tab in columns Relative horizontal tabAbsolute horizontal tab in inches Print double-density, double-speed graphics Print normal-density graphicsPrint double-density graphics Convert graphics density Select graphics modePrint quadruple-densitygraphics Select g-pin graphics mode Download Character Commands Define draft download charactersDefine NLQ download characters Copy character set from ROM into RAM Se/ect download character set Shift download character areaSelect draft pica download character set Select draft elite download character setSelectdraftdownloadcharacterswithdouble-strike Select NLQ download charactersSelect NLQ download characters with italic Select ROM character setColor Selection Commands Select print colorCancel last line Other Printer CommandsSet MSB to Accept MSB as isSet printer off-line Set printer on-lineBell Bi-directional printingUni-directional printing One-line w&directional printingManual feed Auto feedReset printer Select ASF bin #1Select ASF bin #2 Eject paper from ASF

XR-1520, XR-1020 specifications

The Star Micronics XR-1520 and XR-1020 series printers are durable, high-performance devices designed for a variety of printing applications, particularly in retail and hospitality environments. These compact printers are engineered to deliver efficient receipt and label printing, catering to the needs of businesses that demand reliability and speed.

One of the standout features of the XR-1520 and XR-1020 is their advanced thermal printing technology. This method eliminates the need for ink or toner, reducing the operational costs significantly while also minimizing maintenance. The printers utilize direct thermal printing, which produces high-quality prints with sharp text and graphics. This is particularly advantageous for businesses that require clear and legible receipts.

Both models are equipped with fast print speeds, capable of delivering up to 200 mm per second. This ensures quick transaction times, enhancing customer satisfaction and streamlining service. The XR-1520, designed for high-volume environments, can handle larger print jobs efficiently, while the XR-1020 is ideal for smaller businesses or those with moderate printing needs.

Durability is another critical feature of these printers. Star Micronics has engineered the XR series to withstand the rigors of a busy retail environment. They boast robust construction that protects against everyday wear and tear, while their compact design allows for easy placement on countertops or in tight spaces.

Connectivity options are versatile, accommodating a range of modern point-of-sale systems. The XR-1520 and XR-1020 support USB, Ethernet, and serial connections, ensuring compatibility with various devices. Additionally, they are equipped with Bluetooth capabilities, allowing for wireless printing from mobile devices, further enhancing their functionality.

User-friendliness is paramount in the design of both models. They come with intuitive controls for easy operation and integration. They also feature an easy paper loading mechanism that reduces the downtime associated with replacing paper rolls.

In summary, the Star Micronics XR-1520 and XR-1020 printers stand out with their advanced thermal printing technology, high-speed performance, robust durability, versatile connectivity options, and user-friendly design. These characteristics make them an excellent choice for businesses seeking dependable, efficient, and high-quality printing solutions.
Top Page Image Contents