Star Micronics XR-1520 Forward micro-feed, Reverse micro-feed, Changing the auto loading value

Page 59

3.

Press and hold the I

ON LINE

I button.

 

4.

While holding the 1

ON LINE

1button down, press the [ml

but-

 

ton, then release both buttons at the same time. The printer will beep to

 

indicate that the top-of-form position has been set.

 

Forward micro-feed

For fine alignment, you can feed the paper forward in very small increments as follows:

1.Press the 1 ON LINE 1 button to set the printer Off-line.

2.Press the 1 ON LINE I button again and hold it down.

3.While holding the 1 ON LINE 1button down, press the I PAPER FEED I button. The paper will start advancing in a series of small steps. When you want to stop, release both buttons.

c

Reverse micro-feed

You can also feed the paper in small increments in reverse, to return to a higher position on the same page.

NOTE : With fanfold forms, do not try to return to a previous page. The perforation may catch inside the printer.

1.Press the [ ON LINE I button to set the printer off-line.

2.Press the I ON LINE ] button again and hold it down.

3. While holding the IN LINE 1button down, press the I”“&!~&IZ”‘] button. The paper will start moving backwards in a series of small steps. When you want to stop, release both buttons.

Changing the auto loading value

Normally, the printer automatically loads the paper one line from the top edge.

LIf you want to change this value, follow this procedure:

L

1. Load the paper using the lBE;S/A&IPTI button.

2. Change the print position using the micm feed function.

L

3. After you get the desired position, press the I ON LINE 1button to save the value.

51

Page 58 Page 60
Image 59
Page 58 Page 60
Contents XR-1020 XR-1520 Federal CommunicationsCommission HOW to USE this Manual Reference Contents On Line button Printer Control Commands Index Chapter Features of the PrinterPrinter Components Page Tms Romn 0123456789ABCDEFGHIJKLMabcdefghijklm Font Style ExampleLocating the Printer Setting UP the PrinterUnpacking and Inspection Page Mounting the platen knob Setting UPInstall the ribbon cartridge Figure Z-4. Installing the ribbon cartridge Connecting the interface cableFigurn 2-6. Move the clips until you hear a did Memo Single- Bin a utoma tic Sheet Feeder Automatic Sheet FeederPage 33. Attach the stacker to the Automatic Sheet Feeder Gum 3-S Close he front cover Figum 3-7. insert the stacker attachments SF- 1ORMWI5RMII Dual-Bin Automatic Sheet FeederPage Pull Tractor Unit PT-1OXM/15XM Above when removing the FWl Tractor Unit Interface Cartridges Iz-+E DIP Switch Functions on The Serial Interface CartridgeMemo Selection of Paper Paper Installationand USEShows the recommended print area for each type of papers Adjusting the Printing GAPLoading Fanfold Forms Loading the paper from the rear of the printer Push feed Tractor cover Loading the paper from the bottom of the printer Loading the paper with Push/Pull feed 1button. The paper will be fed past the print Page Paper parking Paper unparking Loading Single Sheets Loading the paper without optional accessoriesFigutu 4-13.Loading a single sheet Loading the paper with optional Automatic Sheet Feeder Paper loading lever Single-Bin Paper loading leve Eswre bar lever Single-Bin Chapter Paper Feed button On Line buttonPitch button SET/EJECT/PARK buttonFont button Mode buttonPOWER-UP Functions Short test modeLong test mode Pitch and Font lock mode Print area test modePitch lock mode Font lock modeFigurn 5-S Samplehexadecimaldump Hexadecimal dumpCoding for IBM-PC with color adapter Top of form Switch Combination FunctionsChanging the auto loading value Forward micro-feedReverse micro-feed Selecting the print color Clearing the buffer/AI/ resetSelecting the ASF bin number Store Macro Definition Setting UP Memory Switches Linmenu Enwe Print current settingsCommand menu Installation menuFont menu Print menu Paper menu Factory settings DOT Adjustment Mode To exit from this mode, press Button Printer Control Commands Select NL Q characters Select draft pica charactersSelect draft elite characters Select italic characters Se/ect NLQ fontSelect font Emphasized printing Select upright characters Mode AsciiCancel emphasized printing Select NLQ italic characters HlodeI AsciiStar? 0 verlining Cancel double-s trike printingStart underlining Stop underliningSubscript Cancel superscript or subscriptSuperscript Select character set #2 Select standard character setSelect IBM character set Select character set #ISelect IBM code Select international Character setSelect normal zero Enable printing of all character codesEnable printing of all character codes on next Character Select slash zeroCondensed printing Cancel condensed printingPica pitch Elite pitchExpanded printing for one line Cancel expanded printingCancel one-line expanded printing Expanded printingIncrease character spacing Select master print modeSelect fixed spacing Print double-height characters Select double or quadruple sizeSelect character size Select character height, width, and line spacing -’ Return to normal heightSet line spacing to n/216 inch Set line spacing to l/8 inchSet line spacing to 7/72 inch Set line spacing to l/6 inchReverse line feed Set line spacing to nfl2 inchExecute ES6 Line feedSet top of page at current position Perform one n/216=inchline feedPerform one n/216=inchreverse line feed Feed paper n linesSet bottom margin Cancel bottom marginSet page length to n lines Set page length to n inchesSet vertical tab stops Disable paper-out detectorEnable paper-out detector Return to top of currentSet vertical tab stops in channel Set vertical tab stops every n linesSelect vertical tab channel Vertical tabSet right margin Horizontal Position CommandsSet left margin Set automatic line feed Cancel automatic line feedSet left and right margins Carriage returnFull justify Left justifyCenter text Right justifyHorizontal tab Reset all tab stopsSet horizontal tab stops Set horizontal tab stop every n columnsAbsolute horizontal tab in columns Relative horizontal tabAbsolute horizontal tab in inches Print double-density, double-speed graphics Print normal-density graphicsPrint double-density graphics Convert graphics density Select graphics modePrint quadruple-densitygraphics Select g-pin graphics mode Define draft download characters Download Character CommandsDefine NLQ download characters Copy character set from ROM into RAM Select draft elite download character set Se/ect download character setShift download character area Select draft pica download character setSelect ROM character set Selectdraftdownloadcharacterswithdouble-strikeSelect NLQ download characters Select NLQ download characters with italicSelect print color Color Selection CommandsAccept MSB as is Cancel last lineOther Printer Commands Set MSB toBi-directional printing Set printer off-lineSet printer on-line BellAuto feed Uni-directional printingOne-line w&directional printing Manual feedEject paper from ASF Reset printerSelect ASF bin #1 Select ASF bin #2

XR-1520, XR-1020 specifications

The Star Micronics XR-1520 and XR-1020 series printers are durable, high-performance devices designed for a variety of printing applications, particularly in retail and hospitality environments. These compact printers are engineered to deliver efficient receipt and label printing, catering to the needs of businesses that demand reliability and speed.

One of the standout features of the XR-1520 and XR-1020 is their advanced thermal printing technology. This method eliminates the need for ink or toner, reducing the operational costs significantly while also minimizing maintenance. The printers utilize direct thermal printing, which produces high-quality prints with sharp text and graphics. This is particularly advantageous for businesses that require clear and legible receipts.

Both models are equipped with fast print speeds, capable of delivering up to 200 mm per second. This ensures quick transaction times, enhancing customer satisfaction and streamlining service. The XR-1520, designed for high-volume environments, can handle larger print jobs efficiently, while the XR-1020 is ideal for smaller businesses or those with moderate printing needs.

Durability is another critical feature of these printers. Star Micronics has engineered the XR series to withstand the rigors of a busy retail environment. They boast robust construction that protects against everyday wear and tear, while their compact design allows for easy placement on countertops or in tight spaces.

Connectivity options are versatile, accommodating a range of modern point-of-sale systems. The XR-1520 and XR-1020 support USB, Ethernet, and serial connections, ensuring compatibility with various devices. Additionally, they are equipped with Bluetooth capabilities, allowing for wireless printing from mobile devices, further enhancing their functionality.

User-friendliness is paramount in the design of both models. They come with intuitive controls for easy operation and integration. They also feature an easy paper loading mechanism that reduces the downtime associated with replacing paper rolls.

In summary, the Star Micronics XR-1520 and XR-1020 printers stand out with their advanced thermal printing technology, high-speed performance, robust durability, versatile connectivity options, and user-friendly design. These characteristics make them an excellent choice for businesses seeking dependable, efficient, and high-quality printing solutions.
Top Page Image Contents