Star Micronics XB24-250 II Setting the top of form position, Tear-off function fanfold paper

Page 26
This procedure feeds fanfold paper to a position where it can be torn off easily.

20Control Panel Operations

Setting the top of form position

The current position of paper loaded in the printer is automatically set as the top of the page whenever you turn power on. You can also use the following procedure at any time to specify a different position as the top of the page.

Make sure the printer is off-line (ON LINE indicator is not lit).

Use the micro feed operations (see above) to move the paper so that the print head is located where you want the new top of form position to be.

While holding down FONT, press SET/EJECT/PARK.

The printer will beep once to indicate that a new top of form position has been set.

Tear-off function (fanfold paper)

Check to make sure that the printer is on-line.

Press the FORM FEED button to perform the long tear-off operation, or press the LINE FEED button to perform the short tear-off operation.

The long tear-off operation causes the paper to be fed automatically so the tear assist edge of the printer cover is aligned with the paper’s next perforation.

The short tear-off operation causes the paper to be fed automatically so the tear assist edge of the printer cover is located just below the last line printed on the paper.

Pull the paper against the tear assist edge to tear it off.

When you resume printing, the printer reverse feeds the paper to its former position.

Selecting the Quiet Print Mode

The Quiet Print Mode lets you print with less noise than that produced with normal printing. Use the following procedure to enter and exit the Quiet Print Mode.

Important!

Though the Quiet Print Mode prints more quietly, it also causes printing to take considerably longer than normal printing.

Image 26
Contents XB24-2502 Trademark acknowledgments About this manual ChapterPrinter Setup Control Panel OperationsOptional Accessories Using the EDS ModeUsing the Printer with MS-DOS Paper HandlingPage Printer Setup Choosing a place for the printerUnpacking the printer General guide Installing the platen knob Opening the front coverInstalling the ribbon cartridge Removing the front coverPrinter Setup Installing the paper guide Removing the ribbon cartridgeAdjusting the paper guide position Connecting to a power outlet and turning power on and offLoading fanfold paper Printer Setup Loading fanfold paper Printing on fanfold paper Unparking fanfold paper Using the tear-off functionParking fanfold paper Connecting to your computer Connecting to your computer Switching between on-line and off-line Control Panel OperationsSelecting a font Entering the Font Lock ModeLit Indicator Font Lit Indicators Meaning Setting the character pitchEntering the Pitch Lock Mode Form feed fanfold paper Line feedPaper eject cut-sheet paper Micro feedTear-off function fanfold paper Setting the top of form positionSelecting the Quiet Print Mode Changing the auto load position Changing the auto load positionSaving a macro Clearing the printer’s bufferEntering the Multi-part Mode Initializing the printerEntering the EDS Mode Using the EDS ModeAbout EDS Mode settings Lit Indicator Selected Bank Selecting a switchChanging a switch setting Lit Indicator Selected SwitchExiting the EDS Mode Printing the current switch settingsChecking the settings of switches in a bank EDS Mode Settings Switch 2 Auto Tear-off Long Switch 6 Multi-Part ModeSwitch 1 Graphics Direction Switch 3 Line SpacingSwitch 6 Quiet Switches 1, 2 Print ModeSwitches 3, 4, 5 Print Pitch Print ModeSwitch 6 Not used Switches 1, 2, 3, 4 Page LengthSwitch 5 CR Centering Position LengthCode SW1 SW2 SW3 SW4 SW5 SW6STD 988 TIS Name Country Remarks IBM PCGreece For Unix International Character SetSwitches 1, 2, 3, 4, 5 LQ Font Selection Bank FUsing the Printer with MS-DOS Setting up for printing with MS-DOSCut-Sheet Paper Manual Feed Paper HandlingSelecting paper types Cut-Sheet Paper with Optional Automatic Sheet FeederAdjusting for paper thickness Adjusting for paper thicknessThickness Automatic fanfold feedingManual sheet feeding Clearing paper jams Clearing paper jamsPreparing the printer Optional AccessoriesAutomatic Sheet Feeder SF-15DM Pull Tractor Unit PT-15XM Serial Interface Cartridge IS-8XLBuffered Parallel Interface Cartridge IP-128XL Serial-to-Parallel Converter SPC-8KSpecifications Self test Appendix a TroubleshootingTesting the printer Adjusting the dot alignment Hexadecimal dumpDOT Adjustment Setting Troubleshooting guide Problem Possible CausePrinter case is hot Printer’s air vents are Left margin moves to Paper is not loaded Checking system software settings in MS-DOS Mode LPT1=COM1 or Mode LPT1=COM2Appendix B Specifications Cut-sheet with optional automatic sheet feeder EnvironmentPaper Cut-sheet manual feeding Fanfold with push tractor feederPower Consumption Dimensions and weightPower Supply Ribbon LifeOptional Serial Interface Appendix C Interface Pin OutsParallel Interface Pin Name FunctionAppendix D Character Sets Standard Italic Character Set International Character SetIBM Character Set #2 Code Page #437 IBM-PC Character Set #1 Code Page #850 Multi-lingual IBM Special Character SetCode Page #860 Portuguese Code Page #861 IcelandicCode Page #865 Nordic Code Page #863 Canadian FrenchCode Page #866 Russian Code Page #3840 IBM-RussianCode Page #3843 Polish Code Page #3841 Gost-RussianCode Page #3844 Code Page #3845 HungarianCode Page #3847 Brazil-ABNT Code Page #3846 TurkishCode Page #3848 Brazil-ABICOMP Code Page #852 Latin-2Code Page #1001 Arabic Code Page #737 Greek Code Page #851 GreekCode Page #928 Greek Code Page #869 GreekCode Page #2001 Lithuanian-KBL Code Page #772 LithuanianCode Page #3001 Estonian1 Code Page #774 LithuanianCode Page #3002 Estonian2 Code Page #3011 Latvian1Code Page #3021 Bulgarian Code Page #3012 Latvian2Code Page #3031 Hebrew Code Page #3041 MalteseCode Page #3860 Rajvitee KU Code Page #3850 Standard KUCode Page #3861 Microwiz KU Code Page #3863Code Page #3864 Popular TIS Code Page #3865 Newsic TISAscii Code Function Standard ModeAppendix E Printer Control Codes Printer Control Codes Enable printing of upper control codes Character Set #2 Denmark OCR-B Set left margin Standard Mode IBM Mode Select print pitch and download Ascii Code Function Appendix F Control Panel Operation Guide Form Feed Line Feed On LinePage MS-DOS MS-DOS Worldwide Headquarters

XB24-250 II specifications

Star Micronics has long been a leader in the development of innovative printing technologies, and the XB24-250 II is a testament to this legacy. This advanced thermal receipt printer is designed to cater to the increasing demands of retail and hospitality businesses, providing them with a robust, efficient, and reliable solution for their printing needs.

One of the standout features of the XB24-250 II is its exceptional printing speed. With the ability to print at 250 mm per second, it significantly reduces customer wait times and improves overall service efficiency. This high-speed performance is complemented by high-resolution printing, presenting clear and crisp text as well as detailed graphics, which is essential for modern businesses that aim to enhance their branding.

The XB24-250 II utilizes advanced thermal printing technology, eliminating the need for ink or toner cartridges. This not only reduces the operating costs associated with traditional printers but also minimizes maintenance requirements. The printer supports various media types, including receipts, tickets, and labels, making it versatile for different applications in sectors like retail, restaurants, and entertainment.

Connectivity is another strong point of the XB24-250 II. Equipped with USB, Ethernet, and Serial interfaces, the printer can easily integrate with existing systems and can be connected to mobile devices, PCs, or POS terminals. Additionally, it supports Bluetooth connectivity, allowing for seamless wireless printing, which is invaluable for businesses that need to operate in a mobile environment.

Durability and reliability are critical in high-demand business settings. The XB24-250 II is built to withstand heavy usage, featuring a hardened casing and components that provide longevity. Its thermal print head has a long lifespan, ensuring consistent quality over time, and reducing the frequency of replacements.

Moreover, this printer takes user convenience into account. It has an easy-to-load paper mechanism that simplifies the paper replacement process, minimizing downtime. The compact design allows for flexible placement, whether on a countertop or in a mobile setup.

In summary, the Star Micronics XB24-250 II combines high-speed performance, advanced thermal technology, versatile connectivity options, and exceptional durability to deliver an outstanding printing solution for businesses of all sizes. Its focus on efficiency and user experience makes it a valuable addition to any point-of-sale system, providing a seamless tool for enhancing customer interactions.