TRENDnet TEW-637AP 3.01 manual IAPPInter-Access Point Protocol, Protection, Frame aggregation

Page 24

transmitting the shorter preamble at 1Mbps and the header at 2Mbps, shortening the transmit time to 96 Usec.

IAPP(Inter-Access Point Protocol)

IEEE 802.11F or Inter-Access Point Protocol is a recommendation that describes an optional extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems.

The protocol is designed for the enforcement of unique association throughout an Extended Service Setand for secure exchange of station's security context between the current AP and the new AP during the handoff period. Based on security level, communication session keys between Aps are distributed by a RADIUS server. The RADIUS server also provides a mapping service between AP’s MAC address and IP address.

Protection

These protection mechanisms ensure that a STA that is a potential interferer defers any transmission for a known period of time. These mechanisms are used to ensure that non-ERP STAs do not interfere with frame exchanges using ERP PPDUs between ERP STAs and that non-HT STAs do not interfere with frame exchanges using HT PPDUs between HT STAs, thereby allowing non-ERP and/or non-HT STAs to coexist with ERP and/or HT STAs.

Frame aggregation

Frame aggregation is a feature of the IEEE 802.11e and 802.11n wireless LAN standards that increases throughput by sending two or more data frames in a single transmission. Every frame transmitted by an

802.11device has a significant amount of overhead, including radio level headers, media access control (MAC) frame fields, interframe spacing, and acknowledgment of transmitted frames. At the highest data rates, this overhead can consume more bandwidth than the payload data frame. To address this issue, the draft 802.11n standard defines two types of frame aggregation: Mac Service Data Unit (MSDU) aggregation and MAC Protocol Data Unit (MPDU) aggregation. Both types group several data frames into one large frame. Because management information needs to be specified only once per frame, the ratio of payload data to the total volume of data is higher, allowing higher throughput.

MSDU aggregation

MSDU aggregation relies on the fact that most mobile access points and most mobile client protocol stacks use Ethernet as their "native" frame format. It collects Ethernet frames to be transmitted to a single destination and wraps them in a single 802.11n frame. This is efficient because Ethernet headers are much shorter than 802.11 headers.

MPDU aggregation

MPDU aggregation also collects Ethernet frames to be transmitted to a single destination, but it wraps each frame in an 802.11n MAC header. Normally this is less efficient than MSDU aggregation, but it may be more efficient in environments with high error rates, because of a mechanism called block acknowledgement. This mechanism allows each of the aggregated data frames to be individually acknowledged or retransmitted if affected by an error.

Guard interval

In telecommunications, guard intervals are used to ensure that distinct transmissions do not interfere with one another. These transmissions may belong to different users (as in TDMA) or to the same user (as in OFDM). The standard symbol guard interval used in 802.11 OFDM is 0.8μs. To increase data rate, 802.11n added optional support for a 0.4μs guard interval. This provides an 11% increase in data rate.

Short GI (Shorter guard interval)

The shorter guard interval results in a higher packet error rate when the delay spread of the channel exceed the guard interval and/or if timing synchronization between the transmitter and receiver is not precise. A scheme could be developed to work out whether a short guard interval would be of benefit a particular link. To reduce complexity, manufacturers typically only implement a short guard interval as a final rate adaptation step when the device is running at its highest data rate.

Page 24

Image 24
Contents Page Federal Communication Commission Interference Statement FCC Radiation Exposure StatementEurope EU Declaration of Conformity Page Contents Package Contents Minimum System RequirementsFeatures IntroductionHardware Overview WPS ButtonRear View Installation Considerations Getting Started Page Page Page Page Page Page Using the Configuration Menu Network LAN Setting NetworkWireless Wireless BasicRepeater Mode Support Wireless Mode WDS ModeNetwork Name Ssid Multiple Ssid #Operating Mode Channel BandwidthGuard Interval Reserve Direction Grant RDGWireless Advanced Beacon IntervalFragment Threshold RTS ThresholdIAPPInter-Access Point Protocol ProtectionFrame aggregation Msdu aggregationMAC Filter Security WPA/WPA2 Mode Group Key Update IntervalWPA/WPA2-Personal and Enterprise Cipher TypeWPA/WPA2-Personal WPA/WPA2-EnterpriseWPA/WPA2 mixed environment WPS mode WPSStation List Administrator System ManagementUpload Firmware Settings Management StatusBootp GlossaryAscii CATDhcp DNSEAP FTPGUI HttpHttps IcmpIPX ISPLAN LEDNIC NTPOfdm OSIRIP RSASIP SmtpTCP/IP TftpUDP URLWisp WlanWPA Specifications Limited Warranty PWP05202009v2