TRENDnet TEW811DRU manual Clone a MAC address, Change your router IP address, Network LAN Setting

Page 34

TRENDnet User’s Guide

Clone a MAC address

Network > WAN Setting

On any home network, each network device has a unique MAC (Media Access Control) address. Some ISPs register the MAC address of the device (usually a router or a computer) connected directly to the modem. If your computer MAC address is already registered with your ISP and to prevent the re-provisioning and registration process of a new MAC address with your ISP, then you can clone the address (assign the registered MAC address of your previous device to your new router). If you want to use the MAC address from the previous device (computer or old router that directly connected to the modem, you should first determine the MAC address of the device or computer and manually enter it into your router using the clone MAC address feature.

Note: For many ISPs that provide dynamic IP addresses automatically, typically, the stored MAC address in the modem is reset each time you restart the modem. If you are installing this router for the first time, turn your modem before connecting the router to your modem. To clear your modem stored MAC address, typically the procedure is to disconnect power from the modem for approximately one minute, then reconnect the power. For more details on this procedure, refer to your modem’s User Guide/Manual or contact your ISP.

1.Log into your router management page (see “Access your router management page” on page 31).

2.Click on Network, and click on WAN Settings.

3.Next to MAC Address field, enter the MAC address of your computer.

Note: You can check the DHCP Client List for the MAC addresses of the devices on your network, see page 36 or refer to your computer or device documentation to find the MAC address.

4. To save changes, click Apply.

TEW-811DRU

Change your router IP address

Network > LAN Setting

In most cases, you do not need to change your router IP address settings. Typically, the router IP address settings only needs to be changed, if you plan to use another router in your network with the same IP address settings, if you are connecting your router to an existing network that is already using the IP address settings your router is using, or if you are experiencing problems establishing VPN connections to your office network through your router.

Note: If you are not encountering any issues or are not faced with one of the cases described above or similar, it is recommended to keep your router IP address settings as default.

Default Router IP Address: 192.168.10.1

Default Router Network: 192.168.10.0 / 255.255.255.0

1.Log into your router management page (see “Access your router management page” on page 31).

2.Click on Network, and click on LAN Setting.

3.In LAN Interface Setting section, Enter the router IP address settings.

IP Address: Enter the new router IP address. (e.g. 192.168.200.1)

Subnet Mask: Enter the new router subnet mask. (e.g. 255.255.255.0)

Note: The DHCP address range will change automatically to your new router IP address settings so you do not have to change the DHCP address range manually to match your new router IP address settings.

4.To save changes, click Apply. Note: You will need to access your router management page using your new router IP address. (e.g. Instead of using the default http://192.168.10.1 your new router IP address will use the following format using your new IP address http://(new.ipaddress.here) to access your router management page. You can also use the default login URL http://tew-811dru

© Copyright 2013 TRENDnet. All Rights Reserved.

34

Image 34
Contents Page Table of Contents Router Maintenance & Monitoring Technical Specifications Troubleshooting AppendixFeatures Package ContentsProduct Overview Product Hardware Features Rear ViewApplication Diagram Front ViewHow to setup your router Basic Router SetupHow to set up a home network Where to find more helpRouter Installation Hardware Installation Internet Setup Wizard Click Next to begin the wizard Wireless Setup Wizard TEW-811DRU Connect additional wired devices to your network Wireless Networking and Security Wireless 2.4GHz or 5GHz Security Secure your wireless networkSelecting WEP-OPEN, WEP-SHARED Selecting WPA, WPA2, or WPA2 Mixed AuthenticationNetwork Key WEP Key FormatConnect wireless devices using WPS Connect wireless devices to your routerRecommended Hardware Push Button PBC Method PBC Software/Virtual Push Button Wireless 2.4GHz or 5GHz WPSPIN Personal Identification Number Radio On/Off Basic wireless settingsWireless 2.4GHz or 5GHz Basic ModeClick on Wireless 2.4GHz or 5GHz and click on Guest Network HT Physical ModeWireless 2.4GHz or 5GHz Guest Network Guest NetworkAdvanced Guest Network Settings Steps to improve wireless connectivity Advanced wireless settings Multiple SsidWireless bridging using WDS Wireless Distribution System TEW-811DRU Additional wireless settings Wireless 2.4GHz or 5GHz AdvancedMAC Address Filters Wired LAN MAC Address Filters Access Control FiltersAccess control basics Click on the LAN MAC Filter ModeWireless MAC Address Filters Click on Wireless 2.4GHz or 5GHz, click on SecurityDoman/URL Filters Advanced Access ControlClick on Advanced, click on Access Control Protocol/IP Filters LAN Client FiltersChange your router login password Advanced Router SetupAccess your router management Administrator ManagementChange your device name Manually configure your Internet connectionNetwork WAN Setting Change your device URLIPv6 Internet Connection Settings Network IPv6 SettingClone a MAC address Network LAN SettingChange your router IP address Set up the Dhcp server on your router Set up Dhcp reservationAdvanced Advanced Network Enable/disable UPnP on your routerEnable/disable Application Layer Gateways ALG Advanced ALGClick on Administrator and click on Management Identify your network on the InternetCreate schedules Administrator TimeSet your router date and time Advanced ScheduleVirtual Server Open a device on your network to the InternetAdvanced DMZ Advanced Virtual ServerSpecial Applications Example To forward TCP port 80 to your IP cameraAdvanced Special Application Gaming Allow remote access to your router managementClick on Enabled under Gaming Function section Advanced GamingReview the Inbound/Outbound Class Setting section Prioritize traffic using QoS Quality of ServiceNetwork QoS Add static routes to your router Advanced RoutingAdministrator File Sharing Using External USB StorageSamba Network File Server FTP File Transfer Protocol Server Windows Installation Print Share Utility InstallationClick Install Utility MAC OS X Installation Windows OS Launching the UtilityUtility Main Window Windows OS MAC OS X UtilityDisconnect Configure ServerConnect AboutSending a Request to Connect Connect to a Printer Connect to a Scanner Auto-Connect PrinterClick Auto-Connect Printer Router Default Settings Router Maintenance & MonitoringReset your router to factory defaults Click on Administrator and click on Settings ManagementTo backup your router configuration Backup and restore your router configuration settingsReboot your router To restore your router configurationAllow/deny ping requests to your router from the Internet Upgrade your router firmwareClick on Administrator and click on Upload Firmware Please note the followingClick on Wireless 2.4GHz or 5GHz, and click on Station List Wireless Client ListWireless 2.4GHz or 5GHz Station List Dynamic Dhcp ListCheck the router system information Administrator StatusInternet Configurations System Info5GHz Wireless LAN 4GHz Wireless LANLAN Information IPv6 Status Administrator IPv6 StatusAdministrator System Log View your router logRouter Management Page Structure Technical Specifications StandardsTroubleshooting WindowsHow to find your IP address? AppendixHow to find your MAC address? Apple Menu System Preferences NetworkRoHS Federal Communication Commission Interference StatementFCC Radiation Exposure Statement Europe EU Declaration of ConformityČesky Czech Dansk Danish Limited Warranty