Xantrex Technology PROwatt 600 manual Connecting DC Cables

Page 28

Connecting DC Cables

If you are using crimp connectors, use the tool recommended by the terminal manufacturer. Make sure no stray wires protrude from the terminal. (You can also have the crimp connectors attached by the company that sells you the cable.)

3.Strip about 1/2 inch (1.25cm) from the ends of the cables that will be connected to the inverter.

4.Install a fuse and fuse holder in the cable that will be used for the positive side of the DC circuit. The fuse must be as close to the battery as possible, must be rated for DC circuits, rated 80A max, and have a short-circuit interrupt rating that exceeds the short-circuit current available from the battery.

Xantrex recommends a Bussman ANL-80 fuse or a Gould type A3T80 Class T fuse, or equivalent for installations requiring a “code fuse”.

5.Insert the stripped ends of the cables into the cabling terminals on the rear of the inverter and tighten the screws securely. The red terminal is positive (+); the black terminal is negative (–). See Figure 2.

6.Attach the connector on the negative cable to the negative battery terminal. Make a secure connection. Loose connectors cause excessive voltage drop and may cause overheated wires and melted insulation.

CAUTION: Reverse Polarity

Power connections to the PROwatt 600 must be positive to positive and negative to negative.

A reverse polarity connection (positive to negative) will blow a fuse in the inverter and may cause permanent damage. Your warranty does not cover damage caused by a reverse polarity connection.

13

Page 27 Page 29
Image 28
Page 27 Page 29
Contents PROwatt 600 Inverter PROwatt 600 Inverter Date and Revision About This Guide PurposeScope AudienceOrganization Conventions Used Related InformationPage Important Safety Information General PrecautionsExplosive Gas Precautions Precautions When Working With BatteriesPrecautions For Using Rechargeable Appliances AC Wiring WarningPage Contents Troubleshooting SpecificationsBattery Types and Sizes OperationAlternators and Charging Systems Product and System InformationXiv Introduction Quality Power and Ease of Use Comprehensive ProtectionInstallation Safety Instructions PROwatt 600 MaterialsFront Panel AC End Back Panel DC EndTools Installation Tools and MaterialsMaterials Calculating Battery Requirements Planning Your InstallationChoosing a Charging System Choosing a Location CoolConnecting the Chassis Ground Mounting the InverterGrounding Locations Connecting DC CablesCabling Guidelines Cabling Procedure PROwatt600 Connecting DC Cables Connecting DC Cables Operation Operating Several Loads at Once Turning the Inverter On and OffTurning the Inverter Off Between Charges Green Power LED Reading the Front Panel IndicatorsRed Fault LED Operating Limits Power OutputInput Voltage Inverter Loads Problem LoadsTrouble Loads Battery Charging Frequency Routine MaintenanceTroubleshooting Buzz in Audio Equipment Common ProblemsTelevision Reception Troubleshooting Reference Problem Possible Cause SolutionPage Specifications Electrical Performance PhysicalBattery Types and Sizes Battery Types Automotive Starting BatteriesBattery Size Deep-Cycle Lead-Acid BatteriesBattery Capacity Standards Estimating Battery Requirements To determine the battery capacity you requireBattery Sizing Example Power Operating Appliance Consumption Time per Day = a x BBattery Sizing Worksheet Power Operating Time Appliance Consumption Per day = a x BTwo Batteries Connected In Parallel Two Batteries Connected in ParallelBattery Tips Battery Voltage State of Charge Alternators Charging Systems Charging System Requirements Using Your Vehicle’s Standard Engine AlternatorCharging With an Engine Alternator Using an Alternator Controller Charging From AC PowerUsing a High-Output Alternator Charging From Alternative Energy Sources Product System Information Warranty Return Material Authorization Policy Return Material ProcedureReturn Material Procedure Information About Your System Page Index Index Index Index Tel Fax Email support.prowatt@xanrex.com

PROwatt 600 specifications

Xantrex Technology PROwatt 600 is a powerful and reliable inverter designed to meet the needs of mobile users and off-grid applications. This compact device converts DC power from batteries into AC power, enabling users to run a variety of appliances and equipment that would normally require a standard power outlet. With a continuous power output of 600 watts and a surge capability of 1200 watts, the PROwatt 600 is particularly well-suited for powering smaller electronics, tools, and household devices in a variety of settings, such as RVs, boats, and remote work sites.

One of the standout features of the PROwatt 600 is its pure sine wave output. This technology produces electricity that is nearly identical to the power supplied by traditional utility companies, making it safe for sensitive electronics, such as laptops, medical equipment, and sophisticated audio/video systems. The pure sine wave inverter minimizes harmonic distortion and ensures that devices operate efficiently and without the risk of damage, which is essential for protecting your valuable electronics.

The compact and lightweight design of the PROwatt 600 makes it easy to transport and install. The unit comes with mounting brackets and has a slim profile that allows for convenient installation in tight spaces. Additionally, the fanless operation of the inverter results in silent performance, making it an excellent choice for use in quiet environments, such as camping trips or residential settings.

Xantrex emphasizes safety and reliability in the PROwatt 600. The inverter is equipped with multiple protection features, including over-voltage, under-voltage, overload, and over-temperature protection. These built-in safeguards help prevent damage to the inverter itself as well as the devices being powered, providing users with peace of mind while operating their equipment.

The PROwatt 600 is also designed to be user-friendly. With a simple power switch and LED indicators for power status, users can easily monitor and operate the inverter without complex setup procedures. This ease of use makes it accessible for users of all experience levels.

In summary, Xantrex Technology PROwatt 600 is an excellent choice for those seeking a portable and efficient power solution. Its pure sine wave technology, compact design, safety features, and user-friendly operation make it a versatile tool for powering electronics in various mobile and off-grid applications. Whether for work, recreation, or emergency backup, the PROwatt 600 meets the demands of modern power needs with reliability and performance.
Top Page Image Contents