Xantrex Technology PROwatt 600 Reading the Front Panel Indicators, Green Power LED, Red Fault LED

Page 32

Reading the Front Panel Indicators

Reading the Front Panel Indicators

Green POWER LED

The POWER LED is on when the inverter is connected to DC power and the inverter is switched On.

Red FAULT LED

The FAULT LED comes on for one of the following reasons:

Condition

Cause / Action

 

 

Over Temperature

The PROwatt 600 has overheated and shut

Shutdown

down. The inverter may have overheated

 

because it was operated at power levels

 

above its 600W continuous output rating or

 

because it was installed in a location that

 

does not allow it to dissipate heat properly.

 

Turn the inverter off and then back on after

 

it has cooled down.

 

Note: To cool the inverter quickly, remove

 

any loads, and leave the switch on to keep

 

the fan running.

 

 

Overload Shutdown

A severe overload has caused the

 

PROwatt 600 to shut down.

 

Turn it off for 4–5 seconds, correct the fault

 

condition, and turn it back on. Do not turn

 

the inverter on again unless you have

 

corrected the fault condition (removed the

 

load or unplugged it).

 

 

Low Voltage

The supply voltage (battery) has dropped

Shutdown

below 10 V.

 

 

High Voltage

The supply voltage (battery) has exceeded

Shutdown

15 V.

 

 

See “Troubleshooting Reference” on page 23 for further details about the FAULT LED.

17

Page 31 Page 33
Image 32
Page 31 Page 33
Contents PROwatt 600 Inverter PROwatt 600 Inverter Date and Revision About This Guide PurposeScope AudienceOrganization Conventions Used Related InformationPage Important Safety Information General PrecautionsExplosive Gas Precautions Precautions When Working With BatteriesPrecautions For Using Rechargeable Appliances AC Wiring WarningPage Contents Troubleshooting SpecificationsBattery Types and Sizes OperationAlternators and Charging Systems Product and System InformationXiv Introduction Quality Power and Ease of Use Comprehensive ProtectionInstallation Safety Instructions PROwatt 600 MaterialsFront Panel AC End Back Panel DC EndMaterials Installation Tools and MaterialsTools Choosing a Charging System Planning Your InstallationCalculating Battery Requirements Choosing a Location CoolConnecting the Chassis Ground Mounting the InverterCabling Guidelines Connecting DC CablesGrounding Locations Cabling Procedure PROwatt600 Connecting DC Cables Connecting DC Cables Operation Turning the Inverter Off Between Charges Turning the Inverter On and OffOperating Several Loads at Once Red Fault LED Reading the Front Panel IndicatorsGreen Power LED Input Voltage Power OutputOperating Limits Trouble Loads Problem LoadsInverter Loads Battery Charging Frequency Routine MaintenanceTroubleshooting Television Reception Common ProblemsBuzz in Audio Equipment Troubleshooting Reference Problem Possible Cause SolutionPage Specifications Electrical Performance PhysicalBattery Types and Sizes Battery Types Automotive Starting BatteriesBattery Size Deep-Cycle Lead-Acid BatteriesBattery Capacity Standards Estimating Battery Requirements To determine the battery capacity you requireBattery Sizing Example Power Operating Appliance Consumption Time per Day = a x BBattery Sizing Worksheet Power Operating Time Appliance Consumption Per day = a x BTwo Batteries Connected In Parallel Two Batteries Connected in ParallelBattery Tips Battery Voltage State of Charge Alternators Charging Systems Charging With an Engine Alternator Using Your Vehicle’s Standard Engine AlternatorCharging System Requirements Using a High-Output Alternator Charging From AC PowerUsing an Alternator Controller Charging From Alternative Energy Sources Product System Information Warranty Return Material Authorization Policy Return Material ProcedureReturn Material Procedure Information About Your System Page Index Index Index Index Tel Fax Email support.prowatt@xanrex.com

PROwatt 600 specifications

Xantrex Technology PROwatt 600 is a powerful and reliable inverter designed to meet the needs of mobile users and off-grid applications. This compact device converts DC power from batteries into AC power, enabling users to run a variety of appliances and equipment that would normally require a standard power outlet. With a continuous power output of 600 watts and a surge capability of 1200 watts, the PROwatt 600 is particularly well-suited for powering smaller electronics, tools, and household devices in a variety of settings, such as RVs, boats, and remote work sites.

One of the standout features of the PROwatt 600 is its pure sine wave output. This technology produces electricity that is nearly identical to the power supplied by traditional utility companies, making it safe for sensitive electronics, such as laptops, medical equipment, and sophisticated audio/video systems. The pure sine wave inverter minimizes harmonic distortion and ensures that devices operate efficiently and without the risk of damage, which is essential for protecting your valuable electronics.

The compact and lightweight design of the PROwatt 600 makes it easy to transport and install. The unit comes with mounting brackets and has a slim profile that allows for convenient installation in tight spaces. Additionally, the fanless operation of the inverter results in silent performance, making it an excellent choice for use in quiet environments, such as camping trips or residential settings.

Xantrex emphasizes safety and reliability in the PROwatt 600. The inverter is equipped with multiple protection features, including over-voltage, under-voltage, overload, and over-temperature protection. These built-in safeguards help prevent damage to the inverter itself as well as the devices being powered, providing users with peace of mind while operating their equipment.

The PROwatt 600 is also designed to be user-friendly. With a simple power switch and LED indicators for power status, users can easily monitor and operate the inverter without complex setup procedures. This ease of use makes it accessible for users of all experience levels.

In summary, Xantrex Technology PROwatt 600 is an excellent choice for those seeking a portable and efficient power solution. Its pure sine wave technology, compact design, safety features, and user-friendly operation make it a versatile tool for powering electronics in various mobile and off-grid applications. Whether for work, recreation, or emergency backup, the PROwatt 600 meets the demands of modern power needs with reliability and performance.
Top Page Image Contents