|
|
| DECLARATION OF CONFORMITY |
|
|
| |
|
|
| |
|
|
| |
|
|
|
|
| Name of Mfg: | Transition Networks | |
|
| 6475 City West Parkway, Minneapolis MN 55344 USA | |
| Model: | Media Conversion Center 48 VDC Power Supply | |
| Part Number: |
|
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).
|
|
| _April 8, 1999_____ |
| Stephen Anderson, | Date | |
|
|
|
|
COMPLIANCE INFORMATION
UL Listed
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen werantwortlich ist.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques appropriées
Trademark Notice
All registered trademarks and trademarks are the property of their respective owners.
Copyright Restrictions
© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.
Printed in the U.S.A. | 33108.D |
Minneapolis, MN 55344 USA
Optional 48 VDC Power Supply Module
for
INSTALLATION GUIDE
Master/Slave Switch
NOTE: Power Supply Modules can be “hot swapped”.
The
If present, the Master/Slave switch allows the Power Supply Module to be configured as the primary (master) Power Supply Module or as the secondary (slave) Power Supply Module.
If any Power Supply Module WITHOUT a Master/Slave switch is installed in the
If neither Power Supply Module has a Master/Slave switch, primary/secondary status is automatic and
If both Power Supply Modules have Master/Slave switches and both are configured as the primary (master) Power Supply Module, each Power Supply Module contributes a portion of the power to the chassis (“load sharing”).
CAUTION: When installing a Power Supply Module that has a Master /Slave switch in a chassis with a Power Supply Module that does not have a Master/Slave switch, the Power Supply Module with the Master/Slave switch MUST BE CONFIGURED AS PRIMARY (MASTER).
When installing two Power Supply Modules that have Master/Slave switches, at least one Power Supply Module MUST BE CONFIGURED AS PRIMARY (MASTER). Failure to observe this caution could result in damage to, and subsequent failure of, Power Supply Module(s).