Transition Networks CETTF10XX-200 Cable Specifications, Product Features, Fiber Cable, AutoCross

CETTF10xx-200

Operation -- Continued

Product Features

AutoCross™

The AutoCross feature detects and configures the twisted-pair copper port on the CETTF10xx-200 media converter to the correct straight-through (MDI) or crossover (MDI-X) configuration. This feature allows either MDI or MDI-X cable to connect the media converter to devices such as hubs, transceivers, or network interface cards (NICs).

NOTE: When AutoCross is disabled, the 10Base-T (copper) port is in MDI-X (crossover) mode.

Link Pass-Through

The Link Pass-Through feature allows the media converter to monitor both the fiber and copper RX (receive) ports for loss of signal. In the event of a loss of an RX signal (1), the media converter will automatically disable the TX (transmit) signal (2), thus, “passing through” the link loss (3). The far-end device is automatically notified of the link loss (4), which prevents the loss of valuable data unknowingly transmitted over an invalid link.

	media converter A				media converter B
	disables the fiber TX link			loses the fiber RX link
Near-End		Media	2	3		Media		Far-End
Device	1	Converter A				Converter B	4	Device
original fault							media converter B
on the copper link						disables the copper link

NOTE: An enable/disable switch allows the Link Pass-Through feature to be disabled. Link Pass-Through may interfere with the Auto-Negotiation feature of other devices in networks where there are two media converters installed in series.

Cable Specifications

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Fiber Cable

Bit Error Rate:	<10-9
Single mode fiber (recommended):	9 µm
Multimode fiber (recommended):	62.5/125 µm
Multimode fiber (optional):	100/140, 85/140, 50/125 µm
CETTF1011-200	850 nm multimode
Fiber Optic Transmitter Power:	min: -19.0 dBm	max: -14.0 dBm
Fiber Optic Receiver Sensitivity:	min: -32.5 dBm	max: -14.0 dBm
Link Budget:	13.5 dB
CETTF1012-200	1310 nm single mode
Fiber Optic Transmitter Power:	min: -27.0 dBm	max: -10.0 dBm
Fiber Optic Receiver Sensitivity:	min: -34.0 dBm	max: -14.0 dBm
Link Budget:	7.0 dB
CETTF1013-200	850 nm multimode
Fiber Optic Transmitter Power:	min: -19.0 dBm	max: -14.0 dBm
Fiber Optic Receiver Sensitivity:	min: -32.5 dBm	max: -14.0 dBm
Link Budget:	13.5 dB
CETTF1014-200	1310 nm single mode
Fiber Optic Transmitter Power:	min: -27.0 dBm	max: -10.0 dBm
Fiber Optic Receiver Sensitivity:	min: -34.0 dBm	max: -14.0 dBm
Link Budget:	7.0 dB
CETTF1022-200	1310 nm single mode
Fiber-optic Transmitter Power:	min: -15.0 dBm	max: -5.0 dBm
Fiber-optic Receiver Sensitivity:	min: -34.0 dBm	max: -14.0 dBm
Link Budget:	19.0 dB
CETTF1027-200	1300 nm multimode
Fiber-optic Transmitter Power:	min: -19.0 dBm	max: -15.0 dBm
Fiber-optic Receiver Sensitivity:	min: -32.5 dBm	max: -14.0 dBm
Link Budget:	13.5 dB

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.

The fiber optic transmitters on this device meets Class I Laser safety requirements per IEC-825/CDRH standards and complies with 21 CFR1040.10 and 21CFR1040.11.

CAUTION: Visible and Invisible Laser Radiation When Open. Do Not Stare Into Beam Or View Directly With Optical Instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

6 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 7