Transition Networks CETTF10XX-200 Installation, Set the Jumper, Install the Slide-in-Module

CETTF10xx-200

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when setting the 4-position switch and the jumper. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter.

Set the 4-Position Switch						Fiber Port; Up=On
						Copper Port; Up=On
•	The 4-position switch is
							AutoCross™; Up=On
	located	on	the	media
							Link Pass Through; Up=On
	converter circuit board.
•	Use a	small	flat-blade
	screwdriver		to	set	the
	switches (see the drawing).					1	2 3 4

NOTE: When the fiber port or the copper port is disabled (switches 1 and 2), network traffic coming into the media converter is ignored and no traffic flows out. In this mode, the media converter is disconnected from the network.

1.Fiber Port (10Base-FL)

Up	Enables network traffic on the fiber port.
Down	Disables network traffic on the fiber port.

2.Copper Port (10Base-T)

Up	Enables network traffic on the copper port.
Down	Disables network traffic on the copper port.

3.AutoCross

Up	Enables AutoCross (see page 6).
Down	Disables AutoCross.
	(When AutoCross is disabled, the 10Base-T (copper) port is in
	MDI-X (crossover) mode.)

4.Link Pass-Through

Up	Enables Link Pass-Through (see page 6).
Down	Disables Link Pass-Through.
	(When Link Pass-Through is disabled, remote faults are not
	passed along to any downstream equipment.)

Set the Jumper

The jumper is located on the media converter circuit board. Use small needle-nosed pliers or a similar device to set the jumper.

Installation -- Continued

Install the Slide-in-Module

CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the CETTF10xx-200 slide-in-module media converter. Failure to observe this caution could result in damage to, and subsequent failure of, the media converter.

To install the CETTF10xx-200 slide-in-module media converter.

1.Carefully slide the slide-in-module into the installation slot, aligning the module with the installation guides.

2.Ensure that the module is firmly seated inside the chassis.

3.Push in and rotate the attached panel fastener screw clockwise to secure the module to the chassis front.

		TX PWR			PWR		PWR	PWR
			LKS		LKS	LA		LKS	SPD	PWR
			LKM		LKM	RXF		LKM	FRX	FLNK
		RX	LNK			RXC	COL		CRX	CLNK
		R	TX		TX			TX
							Link Alert
		E				E	D
		S	Singlemode					Singlemode	TX
		E
		T							100BASE-FX
		10BASE-T			PWR	10BASE
I 0	I 0				Singlemode
			RX		RX	-		RX
				RXF	LKF	FL		TX	RX
			TX		TX
				RXC	LKC
		SERIAL	Multimode		Multimode	0	50½	Multimode	100BASE-TX
				TX
						10BASE
			RX		RX	-		RX
						2
		CPSMM120			CFMFF100	CETCF100		CFMFF100	CFETF100
				RX

Panel Fastener Screw

Connect the Twisted-Pair Copper Cable

1.Locate or build IEEE 803.2™ compliant 10Base-T cables, with straight- through RJ-45 cable, and with straight-through RJ-45 connectors installed at both ends.

2.Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the CETTF10xx-200 media converter.

3.Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the other device (switch, workstation, etc.).

Hardware The media converter mode is determined by the 4-position switch settings.

Software The media converter mode is determined by the most-recently saved, on-board microprocessor settings.

H S

Hardware Mode

H S

Software Mode

RJ-45 port	RJ-45 port
on the media	on the other device
converter	(switch, work station, etc.)

2 24-hour Technical Support: 1-800-260-1312-- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 3