Fujitsu N6110 manual Entering the Bios Setup Utility, Navigating Through The Setup Utility

Page 2

L i f e B o o k N S e r i e s N o t e b o o k B I O S

N Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the operating environment for your notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS environment to operate your notebook.

The BIOS Setup Utility configures:

Device control feature parameters, such as changing I/O addresses and boot devices.

System Data Security feature parameters, such as passwords.

Entering the BIOS Setup Utility

To enter the BIOS Setup Utility do the following:

1.Turn on or restart your notebook.

2.Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.

3.Press the arrow keys to scroll through the other setup menus to review or alter the current settings.

Navigating Through The Setup Utility

The BIOS setup utility consists of six menus: Main, Advanced, Security, Boot, Info, and Exit. This document explains each menu in turn, including all submenus and setup items.

The following procedures allow you to navigate the setup utility menus:

1.To select a menu, use the cursor keys: [ ], [].

2.To select a field within a menu or a submenu, use the

cursor keys:

[ ], [ ].

3.To select the different values for each field, press the [Spacebar] or [+] to change to the next higher selection and [F5] or [-] to go to the next lower selection.

4.To activate a submenu press the [Enter] key.

5.To return to a menu from a submenu, press the [Esc] key.

6.To go to the Exit menu from any other menu, press the [Esc] key.

Selecting a field causes a help message about that field to be displayed on the right-hand side of the screen.

Pressing the Enter key with the highlight on a selection that is not a submenu or auto selection will cause a list of all options for that item to be displayed. Pressing the Enter key again will select the highlighted choice.

7.Pressing the [F9] key resets all items in the BIOS to the default values.

8.Pressing the [F10] key saves the current configura- tion and exits the BIOS Setup Utility. You will be asked to verify this selection before it is executed.

9.Pressing the [F1] key gives you a general help screen.

Entering the Setup Utility After a Configuration Change or System Failure

If there has been a change in the system configuration that does not agree with the parameter settings stored in your BIOS memory, or there is a failure in the system, the system beeps and/or displays an error message after the Power On Self Test (POST). If the failure is not too severe, it will give you the opportunity to modify the settings of the setup utility, as described in the following steps:

1.When you turn on or restart the computer there is a beep and/or the following message appears on the screen:

Error message - please run SETUP program Press <F1> key to continue, <F2> to run SETUP

2.If an error message is displayed on the screen, and you want to continue with the boot process and start the operating system anyway, press the [F1] key.

If your notebook emits a series of beeps that sounds like a code and the display is blank, refer to the Troubleshooting sec- tion of your system Use’s Guide. The Troubleshooting Section includes a list of error messages and their meanings.

If your data security settings require it, you may be asked for a password before the operating system will be opened.

2

Image 2
Contents Fujitsu LifeBook Series Navigating Through The Setup Utility Bios Setup UtilityEntering the Bios Setup Utility O S S e t u p U t i l i t y Main Menu Setting Standard System Parameters Fields, Options and Defaults for the Main MenuHard drive Primary MasterProduct number FaceTo select a primary master Primary Master Submenu of the Main MenuAuto Transfer Mode Standard Multiword Mode But it reverts to Mode 5 after the system is rebootedPrimary Slave Submenu of the Main Menu Fast PIO Transfer Mode Standard Multiword DMA2Is selected Logical Block Addressing LBAPOST. Select None if you don’t want to select a device Serial ATA Port 0 Submenu of the Main MenuExiting from Main Menu Main Advanced Security Boot Info Exit Advanced Menu Setting Device Feature ControlsFields, Options and Defaults for the Advanced Menu F1 HelpUSB Features Keyboard Features Submenu of the Advanced Menu ExitVideo Features Submenu of the Advanced Menu Video Features SubmenuInternal Device Configurations Submenu of the Advanced Menu Internal Device Configuration SubmenuMaximized. When Battery Optimized is selected, CPU power CPU Features Submenu of the Advanced MenuEnabled SpeedStepFunctionality. Execute Disable Bit allows the processor to Key are enabled. Note that enabling this feature may cause USB Features Submenu of the Advanced MenuWhen Enabled is selected, Legacy USB Emulation is enabled USB devices are available without a USB-aware OSMiscellaneous Configurations Submenu of the Advanced Menu DisabledEvent Logging Submenu of the Advanced Menu Event Logging SubmenuMain Security Menu Setting the Security FeaturesBoot Info Exit Fields, Options and Defaults for the Security Menu Exiting from the Security MenuHard Disk Security Submenu of the Security Menu Owner Information Submenu of the Security Menu Owner Information SubmenuBoot Menu Selecting the Operating System Source Fields, Options and Defaults for the Boot MenuBoot Device Priority Submenu of the Boot Menu Main Advanced Security Power SavingsExiting from Boot Menu Depending upon your operating environmentInfo Menu Displays Basic System Information Fields, Options and Defaults for the Info MenuBios Version L1 Cache 64 KB Bios Date CPU Speed 86 GHz Memory Slot NoneExit Saving Exit Menu Leaving the Setup UtilityFields, Options and Defaults for the Exit Menu Changes