IBM 243X user manual $+DC3, Problems While Operating the Terminal

Page 73

Troubleshooting and Maintaining the Terminal

4

 

 

Problems While Operating the Terminal (continued)

Problem

Solution

You cannot scan bar code labels.

You are scanning bar code labels, and the terminal appears to be operating slowly.

See “Problems Scanning Bar Code Labels” on page 4-15.

The terminal may be configured for the 5x6, 6x8, or 12x16 font type. These font type values may cause the 243X to scroll, and therefore operate, more slowly when it displays bar code values on the screen. Change the font type to a value other than 5x6, 6x8, or 12x16. For help, see “Display Font Type” or “Display Spacing” in Chapter 6 of the 2400 Family system manual. If the terminal continues to operate slowly, contact your local Intermec service representative for help.

You scan a reader command, such as Change Configuration, and nothing happens.

You scan a valid bar code label to enter data for your application. The data decoded by the terminal does not match the data encoded in the bar code label.

You want to restore the terminal’s default configuration so that you can reconfigure the terminal.

The reader commands are disabled. Scan the Enable Override command shown here to temporarily enable all of the reader commands. You can also enable or disable reader commands with the TRAKKER Antares 2400 Menu System. For help, see “Command Processing” in Chapter 6 of the 2400 Family system manual. When you are finished, remember to disable the override so that your data is not interpreted as a command.

Enable Override

*$+DC3*

*$+DC3*

The terminal may have decoded the bar code label in a symbology other than the label’s actual symbology. Try scanning the bar code label again. Make sure you scan the entire label.

To operate the terminal quickly and efficiently, you should enable only the bar code symbologies that you are going to scan. If you enable multiple symbologies, the terminal may, on rare occasions, decode a bar code according to the wrong symbology and produce erroneous results.

Scan this bar code label:

Default Configuration

*.+*

*.+*

You can also use the TRAKKER Antares 2400 Menu System. For help, see “Restoring the Terminal’s Default Configuration” in Chapter 2 of the 2400 Family system manual.

After you load the default configuration, you may need to set the primary network communications parameters to communicate with other devices in the network.

4-5

Image 73
Contents 243X Hand-Held Terminal Page Contents Configuring the Terminal With the Menu System How to Configure the TerminalConfiguring the Terminal With the Clone Application Configuring Drives and Memory on the TerminalHow to Use This Chapter Contents Using RF Communications on the TerminalBooting the Terminal Troubleshooting a Locked Up ApplicationPage Before You Begin Warranty Information Safety SummaryVii Trakker Antares 243X Hand-Held Terminal User’s Manual About This ManualViii Term Description Chapter SummaryConventions for Input From a Keypad or Keyboard Convention How to Interpret the ConventionConventions for Bar Codes Xii Convention DescriptionLearning About the Terminal Page What Are the Trakker Antares 243X Terminals? CGA-compatible screen Learning About the 243X’s FeaturesOptions for the Terminals Accessories for the Terminals Unpacking the Terminal Determining When the Battery Pack Is Low Using the Terminal’s Battery PackInstalling the Battery Pack Charging the Battery PackTo charge the battery pack To install the battery pack243XU005.eps Managing Battery Power Using the KeypadWays to Save Battery Power SituationFinding the Special Keys Typing the Characters Printed on the Keypad Using the Suspend/Resume KeyColor on Overlay To Type the Character Capitalizing All Characters Using the Modifier KeysUsing the International Keypads Using the TE 2000 Keypads To turn the backlight on and off Using the ScreenTo change the display contrast Protocol Status Icon Off Status Icon Blinks Learning About the Status IconsLearning About the Audio Signals Beep Sequence Situation Using the Terminal’s Serial PortPort COM Port Designation for Applications To scan a bar code label with the scanner Using the Terminal’s ScannerNancy 243X has two different connector module options Learning About the Connector ModulesConnecting an Input Device Connecting to a Serial Device or NetworkScanning Options Defining the Terminal’s Drives To use the 243X for the first time Using the Terminal for the First TimeLearning About the Terminal Page Configuring the Terminal Page About the Configurations How to Configure the TerminalTo access the Rakker Antares 2400 Menu System Configuring the Terminal With the Menu SystemTrakker Antares 2400 Menu System at a Glance Main Menu Configuration MenuSelecting Menus and Commands Accessing Online HelpTo access a help screen Filling In FieldsMarking Check Boxes Reader Command MenuTo enter Ascii characters for a preamble or postamble Entering Ascii Control CharactersCharacters Exiting Screens and Saving ChangesTask Exiting the Menu System Configuring the Terminal With the Clone Application Configuring the RAM Drive Configuring Drives and Memory on the TerminalTo clone configuration parameters and applications Configuring Flash Memory Page Operating the Terminal in a Network Page How the Terminals Fit Into Your Network 243X in a Wired NetworkTCP/IP 2435s in Multiple Subnetworks UDP Plus 2435s in Multiple Subnetworks TCP/IP 2435s Communicating Across Subnetworks UDP Plus Using Serial Communications on the TerminalBinary Protocol Choosing a Communications ProtocolConfigurable Protocol Master Polling Protocol Planning the Network Connection Using RF Communications on the TerminalConfiguring the Access Points Configuring the DCSOpenAir Radio Monitoring Network Communications About the Network ParametersTroubleshooting and Maintaining the Terminal Page Problem See This Section to Find a Solution How to Use This ChapterProblem Problems While Operating the TerminalSolution $+DC3 Problems While Operating the TerminalProblems While Configuring the Terminal Problems While Configuring the Terminal Problem PG command failed Configuration was not updated Problem Problems Communicating With RF Network Devices Problem Problems While Running Applications Problems Transmitting Data Through the DCS Problems Transmitting Data Through the Serial PortProblem Solution Problems Scanning Bar Code Labels Solution Booting the Terminal on Resume Booting the TerminalUsing the Boot Menu Troubleshooting a Locked Up ApplicationTo reset the terminal Resetting the TerminalTo clean the scanner window and terminal screen Cleaning the Scanner Window and Terminal ScreenSpecifications Page Terminal Dimensions Physical and Environmental SpecificationsPower Specifications Electrical SpecificationsScreen Temperature and Environmental SpecificationsKeypad Options Application Options802.11b Radio Specifications SpecificationsOpenAir Radio Specifications Wired Data CommunicationsPin Assignments for COM1 Pin AssignmentsInput Devices and Cables Specifications a Pin Assignments for the Input Device ConnectorsPage Index Page Index CSymbols and NumbersTrakker Antares 243X Hand-Held Terminal User’s Manual Click, audio signals, 1-20 conventions, defined Trakker Antares 243X Hand-Held Terminal User’s Manual Index Trakker Antares 243X Hand-Held Terminal User’s Manual Terminal Emulation Programmer’s Guide

243X specifications

The IBM 243X is part of IBM's OBS (Office of Business Solutions) series, widely recognized for its robust performance and innovative technologies designed for enterprise-level data processing and management. This series is well-suited for organizations demanding reliability, scalability, and efficiency in their operations.

One of the standout features of the IBM 243X is its powerful processing capability. It is equipped with advanced multi-core processors that enable it to handle multiple tasks simultaneously, making it ideal for data-intensive applications such as data analysis, transaction processing, and enterprise resource planning (ERP) systems. The architecture of the IBM 243X ensures optimized performance with minimal latency, ensuring that businesses can operate seamlessly even during peak loads.

In terms of memory and storage, the IBM 243X supports a vast amount of RAM and offers flexible storage options. This allows organizations to customize their configurations based on their specific needs. The device can handle large databases and supports fast access speeds, which is vital for real-time data processing. Additionally, IBM’s proprietary storage technologies ensure data integrity and quick retrieval, contributing to overall operational efficiency.

Safety and security are paramount in today’s digital landscape, and the IBM 243X incorporates several advanced security features. With built-in data encryption, secure boot processes, and compliance with international security standards, the IBM 243X safeguards sensitive business information against unauthorized access and potential cyber threats.

Customization and scalability are also key characteristics of the IBM 243X. Organizations can easily scale their infrastructure up or down based on evolving needs. The modular design allows for added components, which can be integrated without disrupting existing operations, ensuring maximum uptime and productivity.

Furthermore, the IBM 243X leverages cloud integration, enabling businesses to seamlessly connect with various cloud services for backup, disaster recovery, and collaborative work environments. This flexibility positions the IBM 243X as a future-proof investment, offering organizations the ability to adapt to changing technological landscapes.

In summary, the IBM 243X stands out with its robust processing capabilities, extensive memory and storage options, advanced security features, and flexibility for customization and scalability. These characteristics make it an invaluable tool for businesses seeking efficiency, reliability, and performance in their operations.