IBM SBC-659P manual Power Management, Video Off Method

Page 74

Power Management

This category allows you to select the type ( or degree ) of power saving and is directly related to the following modes:

1.HDD Power Down

2.Doze Mode

3.Suspend Mode

Disable (Default)

No power management. Disable all four modes.

 

 

 

Minimum power managemen. Doze mode = 1

Min. Power Saving

hour. Standby mode = 1 hour. Suspend mode =

 

1 hour. HDD Power Down =15 minutes.

 

 

 

Maximum power management--ONLY

Max.Power Saving

AVAILABLE FOR SL CPU'S. Dose mode =

1 min., Standby mode = 1 min., Suspend mode

 

 

= 1 min., and HDD Power Down = 1 min.

 

 

 

Allows you to set each mode individually. When

User Defined

not disabled, each of the tanges are from 1 min.

to 1 hour except for HDD Power Down which

 

 

ranges from 1 min. to 15 min. and disable.

 

 

Video Off Method

This determines the manner in which the monitor is blanked.

 

This selection will cause the system to turn off

V/H SYNC + Blank

the vertical and horizontal synchronization ports

 

and write blanks to the video buffer

 

 

Blank Screen

This option only writes blanks to the video buffer

 

 

DPMS

Initial display power management signaling

 

 

64SBC-659P User Manual

Image 74
Contents SBC-659P Copyright Notice Acknowledgments Aaeon Customer Services Message to the CustomerProduct Warranty Packing list Page Contents Award Bios Setup Drivers and Utilities General Information Introduction Features Specifications Standard Half-size SBC functionsCompact Flash socket onboard Mechanical and environmental Board Layout Board Dimensions Installation Safety precautions Removing the CPUInstalling a CPU Setting jumpers Installing Sodimm Supplementary information about DimmJumpers Jumpers FunctionConnectors Connector FunctionLocating Jumpers and Connectors Locating of Solder Side Connectors Mechanical Drawing Mechanical Drawing Clear Cmos JP2 Front Panel JP1System Frequency JP3 COM2 Ring, +5V, +12V JP4 RS-232/422/485 COM2JP5,JP6 Setting Digital Video Output Connector CN1 Pin SignalExternal Power On Connector CN2 IDE Hard Drive Connector CN3 USB connector CN5, CN6 Floppy Drive Connector CN7 VGA connector CN8 VGA display connector CN8Audio Connector CN9 Ethernet ConnectorsCN12,CN10 COM 1 CN 13 & COM 2 CN 11 Serial Ports Internal Keyboard Connector CN15 Power connector CN16Parallel port connector CN17 Parallel port IRQIrDA Connector CN19 PS/2 keyboard and mouse connectorsCN18CPU Fan power connectors CN20 North bridge chip Fan Connector CN21Compact Flash Connector CN22 Award Bios Setup Starting setup To Enter Setup Before Boot Press DEL KEYSetup keys These keys helps you navigate in Award BiosCase of Problems Getting HelpMain Setup Menu Load Optimized Defaults PnP/PCI ConfigurationLoad Fail-Safe Defaults Set Supervisor/User PasswordStandard Cmos Features Date and Time ConfigurationAward Bios Setup Drive a Drive B Base Memory Halt OnMemory Extended Memory Other MemoryAdvanced Bios Features Virus WarningFirst/Second/Third/Fourth Boot Device Processor Number FeatureQuick Power On Self Test CPU Internal Cache/External CacheBoot Up System Speed Boot Up Floppy SeekBoot Up NumLock Status Swap Floppy DriveTypematic Rate Chars/Sec- Sets the number Typematic Rate Setting- Key strokes repeat at aTypematic Delay Msec- Sets the delay time Security OptionEPA Logo Select HDD S.M.A.R.T CapabilityReport No FDD For WIN 95- Report Small LogoEPA showSdram CAS Latency Time Advanced Chipset FeaturesSdram RAS-to-CAS Delay Sdram Cycle Time Tras/TrcCPU Latency Timer System Bios CacheableVideo Bios Cacheable Delayed TransactionAGP Graphics Aperture Size On board Display Cache Setting CAS LatencyPaging Mode Control Display Cache FrequencyRAS#Percharge Timing RAS-to-CAS OverrideRAS#Timing On-Chip Secondary PCI IDE Integrated PeripheralsOn-Chip Primary PCI IDE IDE Primary/Secondary Master/Slave PIOUSB Controller IDE HDD Block ModePower on Function USB Keyboard SupportUart Mode Select KB Power on PasswordHot Key Power On Onboard FDC ControllerOnboard Serial Ports 1 Parallel Port ModeECP Mode Use DMA Onboard Parallel PortWatch Dog Timer Power Management Setup Acpi FunctionPower Management Video Off MethodVideo Off In Suspend Suspend ModeHDD Power Down Suspend TypeReload Global Timer Events Power On By RingResume By Alarm Reset Configuration Data PnP/PCI ConfigurationsPnP OS installed DMA Resources Resources Controlled ByIRQ Resources PCI/VGA Palette SnoopShutdown Temperature PC Health StatusAuto Detect DIMM/PCI CLK Clock By Slight AdjustFrequency/Voltage Control Spread SpectrumLoad Fail-Safe Defaults Load Optimized Default Load Optimized DefaultSet Supervisor Password Enter PasswordSet User Password Save to Cmos and Exit Save to Cmos and ExitExit without Saving Drivers Installation Installing Drivers Installing Chipset Driver for Windows 95/98 Installing Ultra ATA Storage Driver for Windows 95/98 Installing Intel 82559 for Windows 95 or 98 Ver Installing VGA for Windows 95/98 Installing Audio for Windows 95/98 Installing Security Driver for Windows NT Please perform this procedure firstInstalling Ultra ATA Storage Driver for Windows NT Installing VGA for Windows NT Installing Audio for Windows NT Installing Intel 82559 for Windows NT ==Intel Pro Adapter will appear ==Click on OKInstalling VGA for Windows Installing Audio for Windows