To attach the SCSI and power cables to the tape drive:
1. | Locate | the | SCSI | cable | on | your | computer | (a | ribbon | cable | with | one | |||||||||||||||
| end | connected | to | the | SCSI | adapter) | and |
| find | the |
| next | available |
| connector | that | is | ||||||||||
| farthest | from | the | adapter. | Use |
| all | empty | bus | connectors | beginning | with | the | one | |||||||||||||
| farthest | from | the | adapter to | ensure | better | signal | quality. |
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
Note: | The | SCSI | adapter | might | be |
| part | of |
| the | computer | system |
| board | or | might | be |
| |||||||||
an | adapter | installed | in | an | expansion |
| slot. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
2. | Attach | the | SCSI | cable | from | your | computer | to | the | tape | drive |
| SCSI |
|
|
| |||||||||||
| connector | .1/. | The | SCSI | cable |
| connector |
| at | the | end | of | the | SCSI | cable | will | |||||||||||
| attach to the drive only one |
| way. | Do | not | force | the | cable |
| onto | the | drive. | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
Attention: | Do | not | force | the | power | cable |
| into | the | tape | drive | power | connector. If |
| |||||||||||||
the | power | cable | is | upside | down | and | you |
| force | the |
| connection, | you | might | damage |
|
| ||||||||||
the | drive. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
3. | Connect | the | power | cable | connector | to | the |
| connector |
|
| .2/ | on | the | tape | ||||||||||||
| drive | as | shown | in | the | illustration. | If | all | the | power | cables |
| are | in | use, | purchase a | |||||||||||
| dc |
| available |
| at | most | electronics |
| stores, | and | split a | ||||||||||||||||
| connection | to | make | a | connection | available |
| for the | tape | drive. |
|
|
|
|
|
|
|
|
Step 6. Completing the installation
Check your work before closing the computer.
1. | Be | sure | that | the | power | and SCSI | connectors | are | securely | attached. | Be | sure | that | ||||||||||
| the | cables |
| are | neatly | routed. |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
2. | Replace | the |
| computer | cover | and | secure | it | in |
| place. | Reconnect | the | power |
| cords |
| ||||||
| and | cables. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Step | 7. | Turning | on | the | device |
|
|
|
|
|
|
|
|
|
|
|
| ||||||
Turn | on |
| all | attached | devices; | then | turn | on | your |
| computer. | The tape | drive | performs | a | ||||||||
| (POST) | within | 15 | seconds | and | then | performs | a | drive | reset. |
| ||||||||||||
Step | 8. | Updating | the | configuration |
|
|
|
|
|
|
|
|
|
|
| ||||||||
For | most | computers, | the |
| program | automatically | recognizes |
|
| ||||||||||||||
the | new | tape | drive. | However, | you | might | have | to provide | information | about | your |
| |||||||||||
system |
| changes | after | you | restart | your |
| computer. |
|
|
|
|
|
|
|
|
| ||||||
Ensure | that | the |
| appropriate | advanced | SCSI |
| programming |
| interface |
| (ASPI) | device |
|
|
| |||||||
drivers |
| are | installed | to |
| support the | tape drive. | Device | drivers | are usually | provided | ||||||||||||
with |
| the | SCSI | adapter. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
If | your | computer |
| does | not | recognize | the | tape | drive | after | startup | or | you | receive | startup | ||||||||
errors, |
| run the | utility | program | as | described | in | the | documentation |
| |||||||||||||
that |
| comes | with | your | computer. |
|
|
|
|
|
|
|
|
|
|
|
|
|