Cisco Systems Intelligent Gigabit Ethernet Switch Module manual Message and Recovery Procedures

Page 27

PLATFORM_CAT2950-3-REG_READ_FAILURE: Register read failed for [chars] in [chars]

Explanation This message means that the register read failed for register [chars] in [chars]. An attempt to read a valid location in the internal chip register failed. This could be due to a hardware defect.

Response Find out more about the error by using the show tech-supportprivileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools , see the “Error Message Traceback Reports” section on page .9

PLATFORM_CAT2950-3-REG_WRITE_FAILURE: Register write failed for register [chars] in [chars]

Explanation This message means that an attempt to write to a location in the internal chip register failed. This might be caused by writing to an invalid register location or by a defect in the hardware.

Response Find out more about the error by using the show tech-supportprivileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools , see the “Error Message Traceback Reports” section on page .9

PLATFORM_CAT2950-3-PCI_TEST_FAILURE: PCI address space test failed, Wrote [hex], read [hex], re-read [hex].

Explanation This message means that, during POST, the PCI address space for the ASIC was not mapped correctly. This might occur because of a system PCI-bus problem. The first [hex], the second [hex], and the third [hex] are test data.

Response Find out more about the error by using the show tech-supportprivileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools , see the “Error Message Traceback Reports” section on page .9

PLATFORM_CAT2950-3-SCHAN_OP_FAILURE: S-channel operation timeout for opcode [chars].

Explanation This message means that there was a failure to read or write to an ASIC register or a memory location because of an ASIC internal bus failure. [chars] is the operation code.

Response If the message recurs, find out more about the error by using the show tech-supportprivileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools , see the “Error Message Traceback Reports” section on page .9

PLATFORM_CAT2950-3-SCHAN_READ_REG_FAILURE: S-channel operation read register failure at addr [hex].

Explanation This message means that there was a failure to read the ASIC registers, which might occur because of an invalid register address or internal bus failure. [hex] is the register address.

Response If the message recurs, find out more about the error by using the show tech-supportprivileged EXEC command and by copying the error message exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these online tools , see the “Error Message Traceback Reports” section on page .9

Chapter 2. Message and Recovery Procedures 25

Page 26 Page 28
Image 27
Page 26 Page 28
Contents IBM First Edition June Contents BookTitle change in special and import Conventions PrefaceAudience PurposeEServer BladeCenter Type 8677 Installation and User’s Guide Preface Page System Message Overview How to Read System MessagesSeverity Level Description Output Interpreter Error Message Traceback ReportsPage Message and Recovery Procedures Cigesm Messages Message and Recovery Procedures Page CMP Messages DOT1X Messages DTP Messages EC Messages Message and Recovery Procedures EC-5-NOLACP Invalid EC mode. Lacp not enabled Ethcntr Messages PLATFORMCAT2950 Messages Hwmatmmod MessagesMessage and Recovery Procedures Page Message and Recovery Procedures PM Messages PLATFORMCATALYST2950 MessagesPM-4-BADAPPID An invalid application id dec was detected PM-4-BADCOOKIE chars was detected PM-4-BADVLANID An invalid vlan id dec was detected PM-4-NOSUBBLOCK No PM subblock found for chars Span Messages Port Security MessagesThis section contains the spanning-tree messages Spantree MessagesMessage and Recovery Procedures Page Message and Recovery Procedures SPANTREE-4-PORTNOTFORWARDING chars chars chars Chars port chars Spantreevlanswitch Messages Spantreefast MessagesStormcontrol Messages Swvlan Messages Page Chars chars Charschars Udld Messages Ufastmcastsw Messages Message and Recovery Procedures Page Error Message Explanation and Suggested Solution Appendix A. Security and QoS Configuration MessagesMessage Traceback Reports section on Tools , see the Error Message Traceback Reports section This error message means that there are no free masks This error message means that a hardware failure has This error message means that the granularity of the policer Before you call Appendix B. Getting help and technical assistanceSoftware service and support Hardware service and support Edition notice Appendix C. NoticesIBM TrademarksIndex Numerics Udld Ufast Page IBM@

Intelligent Gigabit Ethernet Switch Module specifications

Cisco Systems is a leader in networking technology, and their Intelligent Gigabit Ethernet Switch Module exemplifies the innovations the company brings to the realm of networking. Designed for flexibility, performance, and scalability, the switch module is tailored for enterprise environments that require robust and reliable network infrastructure.

One of the key features of the Intelligent Gigabit Ethernet Switch Module is its support for high-speed data transfer. With Gigabit Ethernet capabilities, it enables fast and efficient communication between devices, reducing latency and increasing productivity. This high-speed connectivity supports various applications, including video streaming, VoIP, and large file transfers.

Another major characteristic of the module is its versatility. The switch module is compatible with a range of Cisco platforms, allowing users to easily integrate it into their existing network setups. This compatibility means organizations can expand their network capabilities without needing to overhaul their entire infrastructure.

Security is another prominent feature of the Intelligent Gigabit Ethernet Switch Module. It incorporates advanced security protocols, ensuring that sensitive data remains protected as it traverses the network. Features like port security, access control lists (ACLs), and network segmentation help mitigate potential risks and safeguard against unauthorized access.

The module also integrates advanced traffic management technologies. Quality of Service (QoS) features allow administrators to prioritize critical traffic, ensuring that time-sensitive applications receive the necessary bandwidth. Moreover, Layer 2 and Layer 3 capabilities enable efficient routing and switching of data, further enhancing network performance.

Energy efficiency is a hallmark of the Intelligent Gigabit Ethernet Switch Module as well. Cisco has designed the module with environmentally friendly technologies that reduce power consumption, contributing to lower operational costs and a reduced carbon footprint.

In addition, the switch module supports automation and programmability features such as Cisco’s DNA Center, which provides a centralized management platform for monitoring and controlling network activity. This capability allows for easier deployment of policies, enhancing operational efficiency.

Overall, the Cisco Systems Intelligent Gigabit Ethernet Switch Module is a powerful networking solution, combining high-speed performance, advanced security, versatile integration, and efficient management to meet the growing demands of modern enterprise networks. As organizations continue to evolve, this switch module stands out as a reliable choice for companies seeking to optimize their network infrastructure for future challenges.
Top Page Image Contents