Cisco Systems Intelligent Gigabit Ethernet Switch Module manual Message and Recovery Procedures

Page 21

EC-5-CANNOT_BUNDLE_QOS: Removed [chars] from port channel because a QoS policy cannot be supported across multiple DFC cards.

Explanation This message means the specified port cannot join the port channel because the QoS policy attached to the port channel cannot support the multiple Distributed Forwarding Cards (DFCs). [chars] identifies the port that cannot join the port channel.

Response Place the port in another port channel or remove the QoS policy from the port channel.

EC-5-CANNOT_BUNDLE1: Port-channel [chars] is admin-down, port [chars] will remain stand-alone.

Explanation This message means that the EtherChannel is administratively shut down. The first [chars] is the EtherChannel interface, and the second [chars] is the physical interface.

Response Enable the EtherChannel by using the no shutdown interface configuration command.

EC-5-CANNOT_BUNDLE2: [chars] is not compatible with [chars] and will be suspended ([chars]).

Explanation This message means that the interface has different interface attributes than other ports in the EtherChannel. For the interface to join the bundle (EtherChannel), change the interface attributes to match the EtherChannel attributes. The first [chars] is the interface to be bundled, the second [chars] is the physical interface that is already in the bundle, and the third [chars] is the reason for the incompatibility.

Response Change the interface attributes to match the EtherChannel attributes.

EC-5-ERRPROT: Channel protocol mismatch for interface [chars] in group [dec]: the interface cannot be added to the channel group.

Explanation This message means that the interface cannot be added to the channel group by using the specified mode.

Response Change the channel group or the mode for the interface.

EC-5-ERRPROT2: Command rejected: the interface [chars] is already part of a channel with a different type of protocol enabled.

Explanation This message means that the interface cannot be selected for the specified protocol because it is already part of an EtherChannel group with a different protocol enabled.

Response Remove the interface from the EtherChannel group.

EC-5-ERRPROT3: Command rejected: the interface [chars] is already part of a channel.

Explanation This message means that the interface cannot be unselected for the specified protocol because it is already part of an EtherChannel group.

Response Remove the interface from the EtherChannel group.

Chapter 2. Message and Recovery Procedures 19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents IBM First Edition June Contents BookTitle change in special and import Audience PrefacePurpose ConventionsEServer BladeCenter Type 8677 Installation and User’s Guide Preface Page System Message Overview How to Read System MessagesSeverity Level Description Output Interpreter Error Message Traceback ReportsPage Message and Recovery Procedures Cigesm Messages Message and Recovery Procedures Page CMP Messages DOT1X Messages DTP Messages EC Messages Message and Recovery Procedures EC-5-NOLACP Invalid EC mode. Lacp not enabled Ethcntr Messages PLATFORMCAT2950 Messages Hwmatmmod MessagesMessage and Recovery Procedures Page Message and Recovery Procedures PM Messages PLATFORMCATALYST2950 MessagesPM-4-BADAPPID An invalid application id dec was detected PM-4-BADCOOKIE chars was detected PM-4-BADVLANID An invalid vlan id dec was detected PM-4-NOSUBBLOCK No PM subblock found for chars Span Messages Port Security MessagesThis section contains the spanning-tree messages Spantree MessagesMessage and Recovery Procedures Page Message and Recovery Procedures SPANTREE-4-PORTNOTFORWARDING chars chars chars Chars port chars Spantreevlanswitch Messages Spantreefast MessagesStormcontrol Messages Swvlan Messages Page Chars chars Charschars Udld Messages Ufastmcastsw Messages Message and Recovery Procedures Page Error Message Explanation and Suggested Solution Appendix A. Security and QoS Configuration MessagesMessage Traceback Reports section on Tools , see the Error Message Traceback Reports section This error message means that there are no free masks This error message means that a hardware failure has This error message means that the granularity of the policer Before you call Appendix B. Getting help and technical assistanceSoftware service and support Hardware service and support Edition notice Appendix C. NoticesIBM TrademarksIndex Numerics Udld Ufast Page IBM@
Top Page Image Contents