63672

Chapter 2 Ethernet and Gigabit Ethernet Switching Modules

10/100 and 10/100/1000 Ethernet Switching Modules

Figure 2-17 48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6548V-GE-TX)

WS-X6148-GE-TX 1											11
2											12
STATUS
1	2	3	4	5	6	7	8	9	10	11	12

13	23
14	24
48 PORT	10/100/1000

13	14	15	16	17	18	19	20	21	22	23	24	BASE-T GE

25											35	37													47
26											36	38													48
												SWITCHING MODULE													PHONE	90852
25	26	27	28	29	30	31	32	33	34	35	36		37	38	39	40	41	42	43	44	45	46	47	48

The front panel LEDs are described in Table 2-3 on page 2-21.

48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-21)

The 48-port 10/100BASE-T switching module (WS-X6548-RJ-21) provides 48 switched, 10/100-Mbps, full- or half-duplex ports. (See Figure 2-18.) The module has 4 RJ-21 connectors (12 ports per connector) for Category 5, Category 5e, or Category 6 cable. The WS-X6548-RJ-21 module has 1-MB per-port packet buffers and a single fabric channel interface. The switching module is upgradable to support distributed forwarding with an optional Distributed Forwarding Card (WS-F6K-DFC). The WS-X6548-RJ-21 module is auto-MDI/MDIX capable; you can use either straight or crossover cable, and the module will automatically detect and adjust for the cable type.

The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t.

Figure 2-18 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-21)

WS-X6548-RJ21

-12	-24	-36	-48
1	13	25	37

STATUS

											48 PORT													10/100 BASE-T													SWITCHING MODULE
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	ETHERNET	25	26	27	28	29	30	31	32	33	34	35	36	37	38	39	40	41	42	43	44	45	46	47	48

The front panel LEDs are described in Table 2-3 on page 2-21.

48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-45)

The 48-port 10/100BASE-T switching module (WS-X6548-RJ-45) provides 48 switched, 10/100-Mbps, full- or half-duplex ports. (See Figure 2-19.) Ports have RJ-45 connectors for Category 5, 5e, and 6 cable. The WS-X6548-RJ-45 module has 1-MB per-port packet buffers and a single fabric channel interface. The switching module is upgradable to support distributed forwarding with an optional Distributed Forwarding Card (WS-F6K-DFC). The WS-X6548-RJ-45 module is auto-MDI/MDIX capable; you can use either straight or crossover cable, and the module will automatically detect and adjust for the cable type.

The QoS port architecture (Rx/Tx) for this module is 1p1q0t/1p3q1t.

Figure 2-19 48-Port 10/100BASE-T Fabric-Enabled Ethernet Switching Module (WS-X6548-RJ-45)

WS-X6548	1	11	13	23	25	35	37	47
	2	12	14	24	26	36	38	48

STATUS									10	11	12	48 PORT	14	15	16	17	18	19	20	21	22	23	24	10/100 BASE-T	25	26	27	28	29	30	31	32	33	34	35	36	SWITCHING MODULE	38	39	40	41	42	43	44	45	46	47	48	PHONE
1	2	3	4	5	6	7	8	9				13												ETHERNET													37

The front panel LEDs are described in Table 2-3 on page 2-21.

63673

Cisco 7600 Series Routers Module Guide

2-12	OL-9392-04