Cisco Systems PA-FE-FX, PA-FE-TX manual Installing PA-FE Port Adapter Interface Cables

Page 47

C H A P T E R 7

Installing PA-FE Port Adapter Interface Cables

To continue your PA-FE-TX and PA-FE-FX port adapter installation, you must install the port adapter’s interface cables. The following instructions apply to all supported platforms. This chapter contains the following sections:

•

•

PA-FE Port Adapter RJ-45 and MII Connections, page 7-1

Attaching PA-FE Port Adapter Interface Cables, page 7-1

PA-FE Port Adapter RJ-45 and MII Connections

On a single PA-FE, you can use either the RJ-45 (or SC for PA-FE-FX) connection or the MII connection. (RJ-45, SC, and MII cables are not available from Cisco Systems; they are available from outside commercial cable vendors.) If you have two PA-FE port adapters on your VIP2, you can use the RJ-45 (or SC for PA-FE-FX) connection on one port adapter and the MII connection on the other port adapter.

Caution Before you attach your MII transceiver to the MII receptacle on your PA-FE, ensure that your MII transceiver responds to physical sublayer (PHY) address 0 per section 22.2.4.4. “PHY Address” of the IEEE 802.3u specification; otherwise, interface problems might result. Confirm that this capability is available on your MII transceiver with the transceiver’s vendor or in the transceiver’s documentation. If a selection for Isolation Mode is available, we recommend you use this setting (if no mention is made of PHY addressing).

Attaching PA-FE Port Adapter Interface Cables

Use the following procedure to connect RJ-45, SC (PA-FE-FX), or MII cables:

Step 1 If you have MII connections, attach an MII cable directly to the MII receptacle on the PA-FE or attach a 100BaseT transceiver, with the media appropriate to your application, to the MII receptacle on the PA-FE. (See Figure 7-1 for the PA-FE-TX and Figure 7-2 for the PA-FE-FX.)

If you have RJ-45 connections, attach the Category 5 UTP cable directly to the RJ-45 port on the PA-FE. (See Figure 7-1 for PA-FE-TX and Figure 7-2 for PA-FE-FX.) The PA-FE is an end station device and not a repeater. You must connect the PA-FE to a repeater or hub.

If you have an SC connection (PA-FE-FX), attach the cable directly to the SC port on the PA-FE-FX. (See Figure 7-2.) Use either one duplex SC connector or two simplex SC connectors, and observe the correct relationship between the receive (R) and transmit (T) ports on the PA-FE-FX and your repeater.

Installing PA-FE Port Adapter Interface Cables 7-1

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Corporate Headquarters Copyright 1996-1999 Cisco Systems, Inc All rights reserved Objectives PrefaceRelated Documentation OrganizationRelated Documentation Cisco Documentation CD-ROM Cisco Connection OnlinePort Adapter Overview OverviewPA-FE-FX Port Adapter-Faceplate View Port Adapter Locations on the Supported PlatformsCPU Port Adapter Slots in the Cisco 7200 Series-Cisco Receptacles, Cables, and Pinouts LEDsPA-FE-TX RJ-45 Connections-Plug and Receptacle 11 PA-FE-FX Duplex SC Connector 13 PA-FE-TX or PA-FE-FX MII Connection-Receptacle Fast Ethernet Overview MII Ieee 802.3u 100BaseT SpecificationsList of Parts and Tools Preparing for InstallationRouter Platform Recommended Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesElectrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance VIP2 and the PA-FE Port Adapters Installation OverviewVIP2-15 or VIP2-40 with a PA-FE-TX in Port Adapter Slot VIP2-15 or VIP2-40 with a PA-FE-FX in Port Adapter Slot Removing a Port Adapter Removing a Port AdapterLocation of Port Adapter Screw-Partial Port Adapter Installing a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installing a Port Adapter Cisco 7200 Series and the PA-FE Port Adapters Shows a Cisco 7206 with a PA-FE-FX installed in slot Handling a Port Adapter Guide Placing the Port Adapter Lever in the Locked Position-Cisco Installing a Port Adapter Cisco uBR7200 Series and the PA-FE Port Adapters Cisco uBR7200 Series with a PA-FE-TX in Slot 2-Cisco uBR7246 Port adapters Installing a Port Adapter Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Cisco 7120 Series Router-Port Adapter Slot 3 Location Cisco 7100 Series and the PA-FE-TX and PA-FE-FXCisco 7140 series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Attaching PA-FE Port Adapter Interface Cables Installing PA-FE Port Adapter Interface CablesPA-FE Port Adapter RJ-45 and MII Connections Attaching PA-FE Port Adapter Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Attaching PA-FE Port Adapter Interface Cables Configuring PA-FE Port Adapter Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Using the Exec Command InterpreterCisco 7206 Fast Ethernet Interface Port Number Example VIP2 Ports Fast Ethernet Interface Port Number Example-Cisco Cisco 7100 Series PortsPerforming a Basic Configuration Performing a Basic ConfigurationRouter# configure terminal Configuring PA-FE Media Type Configuring PA-FE Transmission ModeChecking the Configuration Using show Commands to Verify the New Interface StatusChecking the Configuration Router# show diag VIP2 Show Commands Router# show diagbus Using the ping CommandRouter# ping

PA-FE-FX, PA-FE-TX specifications

Cisco Systems PA-FE-TX and PA-FE-FX are essential components in the realm of network switching and connectivity. These Peripheral Adapter modules are designed for use in Cisco 7000 series routers, catering to the needs of high-performance networking and offering robust features.

The PA-FE-TX module is equipped with fast Ethernet ports that provide high-speed network connectivity through twisted-pair cabling. This module supports 10/100 Mbps data rates, making it ideal for connecting end-user devices to the network while ensuring compatibility with existing infrastructure. Its auto-sensing capability facilitates smooth integration into varying network environments, allowing for seamless communication and data transfer.

On the other hand, the PA-FE-FX module is tailored for fiber optic connections, enabling high-speed data transmission over longer distances. This module supports multimode and single-mode fiber options, catering to diverse connectivity requirements. The PA-FE-FX is essential for organizations that require extended reach and minimal signal degradation, making it suitable for large campuses, data centers, and urban networking.

Both modules leverage Cisco's advanced technologies, including Quality of Service (QoS) capabilities and enhanced security features. These protocols ensure efficient bandwidth management and prioritize critical applications, improving overall network performance. Additionally, they support features such as VLAN (Virtual Local Area Network) tagging, enabling network segmentation and improved traffic management.

The physical design of these modules adheres to Cisco's standards, ensuring easy installation and hot-swappable capabilities. This means network administrators can replace or upgrade the modules without taking the entire system offline, providing greater flexibility and reducing downtime.

In summary, Cisco's PA-FE-TX and PA-FE-FX modules are integral components for organizations seeking to enhance their networking infrastructure. With their support for both copper and fiber optic connections, they provide versatile options for connecting devices, extending network reach, and improving data transfer speeds. Their compatibility with advanced networking technologies further emphasizes Cisco's commitment to delivering high-quality, reliable networking solutions for businesses of all sizes.
Top Page Image Contents