Cisco Systems PA-FE-FX manual Cisco 7200 Series and the PA-FE Port Adapters, Installation Overview

Page 31

C H A P T E R 4

Cisco 7200 Series and the PA-FE Port Adapters

This chapter provides information on the PA-FE-TX and PA-FE-FX port adapters and their use in the Cisco 7200 series routers. This chapter contains the following sections:

•

•

•

Installation Overview, page 4-1

Removing a Port Adapter, page 4-2

Installing a Port Adapter, page 4-4

Note The Cisco 7206VXR and the Cisco 7206 can be used as router shelves in a Cisco AS5800 Universal Access Server. For information about the Cisco 7206VXR and the Cisco 7206 as router shelves, see the Cisco 7200 Series Port Adapter Hardware Configuration Guidelines .

Installation Overview

You might need to install a new port adapter in a Cisco 7200 series router or replace a failed port adapter in the field. In either case, no tools are necessary; all port adapters available for the Cisco 7200 series routers connect directly to the router midplane and are locked into position by a port adapter lever. When removing and replacing a port adapter, you need an antistatic mat onto which you can place a removed port adapter and an antistatic container into which you can place a failed port adapter for shipment back to the factory.

Note Cisco 7200 series routers support online insertion and removal (OIR); therefore, you do not have to power down the routers when removing and replacing a PA-FE.

When a port adapter slot is not in use, a blank port adapter must fill the empty slot to allow the router to conform to EMI emissions requirements and to allow proper airflow across the port adapters. If you plan to install a new port adapter in a slot that is not in use, you must first remove a blank port adapter.

The PA-FE-TX and PA-FE-FX can be installed in any available port adapter slot in Cisco 7200 series routers. Figure 4-1 shows a Cisco 7206 with a PA-FE-TX installed in slot 4.

Cisco 7200 Series and the PA-FE Port Adapters 4-1

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Corporate Headquarters Copyright 1996-1999 Cisco Systems, Inc All rights reserved Objectives PrefaceRelated Documentation OrganizationRelated Documentation Cisco Documentation CD-ROM Cisco Connection OnlinePort Adapter Overview OverviewPA-FE-FX Port Adapter-Faceplate View Port Adapter Locations on the Supported PlatformsCPU Port Adapter Slots in the Cisco 7200 Series-Cisco Receptacles, Cables, and Pinouts LEDsPA-FE-TX RJ-45 Connections-Plug and Receptacle 11 PA-FE-FX Duplex SC Connector 13 PA-FE-TX or PA-FE-FX MII Connection-Receptacle Fast Ethernet Overview MII Ieee 802.3u 100BaseT SpecificationsList of Parts and Tools Preparing for InstallationRouter Platform Recommended Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesElectrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance VIP2 and the PA-FE Port Adapters Installation OverviewVIP2-15 or VIP2-40 with a PA-FE-TX in Port Adapter Slot VIP2-15 or VIP2-40 with a PA-FE-FX in Port Adapter Slot Removing a Port Adapter Removing a Port AdapterLocation of Port Adapter Screw-Partial Port Adapter Installing a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installing a Port Adapter Cisco 7200 Series and the PA-FE Port Adapters Shows a Cisco 7206 with a PA-FE-FX installed in slot Handling a Port Adapter Guide Placing the Port Adapter Lever in the Locked Position-Cisco Installing a Port Adapter Cisco uBR7200 Series and the PA-FE Port Adapters Cisco uBR7200 Series with a PA-FE-TX in Slot 2-Cisco uBR7246 Port adapters Installing a Port Adapter Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Cisco 7120 Series Router-Port Adapter Slot 3 Location Cisco 7100 Series and the PA-FE-TX and PA-FE-FXCisco 7140 series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides PA-FE Port Adapter RJ-45 and MII Connections Installing PA-FE Port Adapter Interface CablesAttaching PA-FE Port Adapter Interface Cables Attaching PA-FE Port Adapter Interface Cables Attaching the Ferrite Bead around the RJ-45 Cable Attaching PA-FE Port Adapter Interface Cables Configuring PA-FE Port Adapter Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Using the Exec Command InterpreterCisco 7206 Fast Ethernet Interface Port Number Example VIP2 Ports Fast Ethernet Interface Port Number Example-Cisco Cisco 7100 Series PortsPerforming a Basic Configuration Performing a Basic ConfigurationRouter# configure terminal Configuring PA-FE Media Type Configuring PA-FE Transmission ModeChecking the Configuration Using show Commands to Verify the New Interface StatusChecking the Configuration Router# show diag VIP2 Show Commands Router# show diagbus Using the ping CommandRouter# ping

PA-FE-FX, PA-FE-TX specifications

Cisco Systems PA-FE-TX and PA-FE-FX are essential components in the realm of network switching and connectivity. These Peripheral Adapter modules are designed for use in Cisco 7000 series routers, catering to the needs of high-performance networking and offering robust features.

The PA-FE-TX module is equipped with fast Ethernet ports that provide high-speed network connectivity through twisted-pair cabling. This module supports 10/100 Mbps data rates, making it ideal for connecting end-user devices to the network while ensuring compatibility with existing infrastructure. Its auto-sensing capability facilitates smooth integration into varying network environments, allowing for seamless communication and data transfer.

On the other hand, the PA-FE-FX module is tailored for fiber optic connections, enabling high-speed data transmission over longer distances. This module supports multimode and single-mode fiber options, catering to diverse connectivity requirements. The PA-FE-FX is essential for organizations that require extended reach and minimal signal degradation, making it suitable for large campuses, data centers, and urban networking.

Both modules leverage Cisco's advanced technologies, including Quality of Service (QoS) capabilities and enhanced security features. These protocols ensure efficient bandwidth management and prioritize critical applications, improving overall network performance. Additionally, they support features such as VLAN (Virtual Local Area Network) tagging, enabling network segmentation and improved traffic management.

The physical design of these modules adheres to Cisco's standards, ensuring easy installation and hot-swappable capabilities. This means network administrators can replace or upgrade the modules without taking the entire system offline, providing greater flexibility and reducing downtime.

In summary, Cisco's PA-FE-TX and PA-FE-FX modules are integral components for organizations seeking to enhance their networking infrastructure. With their support for both copper and fiber optic connections, they provide versatile options for connecting devices, extending network reach, and improving data transfer speeds. Their compatibility with advanced networking technologies further emphasizes Cisco's commitment to delivering high-quality, reliable networking solutions for businesses of all sizes.
Top Page Image Contents