Cisco Systems OL-7861-01 manual Removing and Installing a Line Card, Required Tools and Equipment

Page 10

Removing and Installing a Line Card

Required Tools and Equipment

You need the following tools and parts to remove and install Ethernet line cards:

•Flat-blade or Phillips screwdriver

•ESD-preventive wrist or ankle strap and instructions

•Interface cables to connect the Ethernet line card with another router or switch

•Any EPAs, GBICs, SFP modules, or memory you need to install (and are not already installed)

Note If you need additional equipment, see Cisco.com or your service representative for ordering information.

Refer to the individual line card descriptions in the “Product Overviews” section on page 4 for more information. Table 4 on page 4 summarized the hardware requirements for each Ethernet line card.

Removing and Installing a Line Card

The following sections provide procedures for removing or installing a line card:

•Guidelines for Line Card Removal and Installation, page 10

•Removing a Line Card, page 11

•Installing a Line Card, page 13

Note See the “Guidelines for Line Card Removal and Installation” section on page 10 before removing a line card while power to the router is on.

Note The procedures in the following sections use illustrations of a Cisco 12012 Internet Router to support the descriptions of removing and installing line cards. Although the card cages of the Cisco 12000 Series Routers differ in the number of card slots, the designated use of slots and the process of removing and installing a line card are basically the same. Therefore, separate procedures and illustrations for other Cisco routers are not included in this publication.

Guidelines for Line Card Removal and Installation

Guidelines for line card removal and installation include the following:

•Online insertion and removal (OIR) is supported, enabling you to remove and install line cards while the router is operating. OIR is seamless to users on the network, maintains all routing information, and ensures session preservation.

Note With OIR, notifying the software or resetting the power is not required. However, you have the option of using the shutdown command before removing a line card.

Cisco XR 12000 Series Router Ethernet Line Card Installation

10

OL-7861-01

 

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Contents Ethernet Line Card Product Numbers Router Hardware InstallationImportant Information Supported PlatformsLine Card Required Part Number Minimum IOS Software Release Hardware VersionRelated Documentation Product OverviewsMemory Options Ethernet Line Card ComparisonPort Gigabit Ethernet ISE Line Card Part NumberPort 1-Gigabit Ethernet Line Card Link Active RX Frame Preparing for Installation Port 10-Gigabit Ethernet Line CardSafety Guidelines Preventing Electrostatic DischargeGuidelines for Line Card Removal and Installation Removing and Installing a Line CardRequired Tools and Equipment Removing a Line Card Line Card Removal and Installation Installing a Line Card Ejector Levers Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line CardRemoving an EPA Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPAMating the Connector of the EPA to the Line Card Push Push Press on the White Labels on the EPA Inserting and Tightening the Screw on the EPA Removing and Installing GBICs Inserting the 2 screws on the Faceplate of the Line CardGeneral Gbic Handling and Maintenance Guidelines Removing the Gbic from an Ethernet Line CardInserting a Gbic into the Gigabit Ethernet Interface Removing and Replacing a GbicRemoving and Installing SFP Modules Bale Clasp SFP ModuleRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP ModuleRemoving a Mylar Tab SFP Module Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Installing an Actuator Button SFP Module Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Removing a Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Line Card Cable-Management BracketSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet InterfaceRJ-45 SC-TypeGigabit Ethernet Interface Gbic Module Distance Connector Type Wavelength Fiber TypeGbic Laser Optical Transceiver Modules Transmit Receive Link PowerBudget Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line Card Gbic Product Number Cwdm Gbic Wavelength Color IdentifierGeneral Cwdm Gbic Installation and Usage Guidelines Gigabit Ethernet SFP Modules Card carrier side of line cardTransceiver Budget Power Power Transmit Receive Typical MaximumSFP Module Type Wavelength Cable Distance Gigabit Ethernet Fiber-Optic Interface CablesTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Removing and Installing Fiber-Optic Interface Cables Simplex LC Cable ConnectorRemoving Fiber-Optic Interface Cables Installing Fiber-Optic Interface Cables Disconnecting Line Card Interface CablesTX connector Simplex cables RX connector Duplex cable Cleaning Fiber-Optic Connectors Type RJ-45 100BASE-T Copper Cables Removing and Installing RJ-45 100BASE-T Copper CableRemoving RJ-45 Cables Initial Boot Process Verifying and Troubleshooting the InstallationInstalling RJ-45 Cables Status LEDs Gigabit Ethernet Status LEDsAlphanumeric LEDs Color/Activity DescriptionLED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Locations Line Card MemoryEthernet Line Card Hardware Engine Engine 2 Line Card Memory Locations ISE Line Card Memory LocationsISE Line Card Memory Locations Ethernet Line Card Route Memory Options Engine 4 Line Card Memory LocationsCisco Product Number Dimm Module Ethernet Line Card Packet Memory Options Removing and Installing Line Card MemoryCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Handling a DimmRemoving a Sodimm Remove Retaining Clip from Memory Module Socket Installing a Sodimm Moving the Plastic Latch Away from the SodimmSodimm Socket Retaining Clip Inserting a 144-pin Sodimm Module Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Completely Installed into Module LatchElectromagnetic Compatibility Regulatory Statements Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals FCC Class a ComplianceCanada Europe EUClass a Notice for Hungary Vcci Class a Notice for JapanLaser Safety Class a Notice for KoreaDocumentation DVD Obtaining DocumentationCisco.com Ordering DocumentationDocumentation Feedback Reporting Security Problems in Cisco ProductsCisco Product Security Overview Obtaining Technical Assistance Submitting a Service RequestCisco Technical Support Website Definitions of Service Request Severity Obtaining Additional Publications and InformationObtaining Additional Publications and Information Obtaining Additional Publications and Information OL-7861-01

OL-7861-01 specifications

Cisco Systems OL-7861-01 is a robust and versatile device designed to meet the demands of modern networking environments. As part of Cisco's extensive portfolio of networking and communication solutions, the OL-7861-01 is tailored for organizations seeking high performance and reliability. The device is primarily deployed in voice over IP (VoIP) solutions, effectively enhancing communication capabilities across various sectors.

One of the standout features of the OL-7861-01 is its support for the latest VoIP technologies. This functionality allows organizations to implement efficient and cost-effective communication systems. Users benefit from crystal-clear voice quality, reduced latency, and improved overall user experience during calls. The device is equipped with advanced codecs, including wideband audio support, ensuring high-definition voice clarity.

In terms of enterprise readiness, the OL-7861-01 boasts seamless integration with Cisco’s Unified Communications Manager, enabling centralized management of communication systems. This integration simplifies deployment and management, allowing administrators to monitor system performance and access a range of administrative tools. Additionally, the device supports full duplex communication, ensuring that users can speak and listen simultaneously without interruptions.

The OL-7861-01 stands out with its robust security measures, which are crucial for protecting sensitive information during transmissions. It incorporates features such as secure RTP (SRTP) and transport layer security (TLS) to safeguard voice data against unauthorized access. This encryption capability is vital for organizations handling confidential communications.

The technological architecture of the OL-7861-01 is designed for scalability and flexibility. Organizations can easily expand their communication capabilities by integrating additional devices or users without significant infrastructure changes. This feature is essential for businesses anticipating growth or needing to adapt to changing communication demands.

Another notable characteristic of the OL-7861-01 is its user-friendly interface. The device is designed with an intuitive layout, allowing users to navigate features effortlessly. Coupled with customizable settings, end-users can tailor their communication experience to suit specific needs.

In summary, Cisco Systems OL-7861-01 is a powerful networking solution that brings together advanced VoIP capabilities, robust security features, and seamless integration with Cisco's communication ecosystem. Its scalability and user-friendly design make it an ideal choice for organizations looking to enhance their communication systems and improve overall productivity.
Top Page Image Contents