Cisco Systems OL-7861-01 manual Preparing for Installation, Port 10-Gigabit Ethernet Line Card

Page 8

Preparing for Installation

1-Port 10-Gigabit Ethernet Line Card

The 1-Port 10-Gigabit Ethernet line card provides the supported Cisco XR 12000 Series Routers with one optical 802.3ae 10-Gigabit Ethernet interface. This interface provides a high-speed connection to other network devices, such as Cisco XR 12000 Series Routers, or to other routers or layer-2 or layer-3 switches that support 10-Gigabit Ethernet interfaces. Figure 3 shows the front view of the line card.

The port on the front panel of the line card is port number 0. This port uses a hardwired laser optical transceiver to provide a 10-Gigabit Ethernet optical interface. The transceiver consists of two optical interfaces—laser transmit (TX) and laser receive (RX)—that use SC connectors.

Next to the port on the line card are three green LEDs, aligned vertically and labeled from top to bottom as follows: LINK, ACTIVE, and RX FRAME.

Figure 3 1-Port 10-Gigabit Ethernet Line Card

 

 

LINK

98893

 

 

 

 

 

ACTIVE

 

 

 

RX FRAME

 

TX

RX

 

1X10GE-LR-SC

 

1

2

3

4

 

5

6

1

Ejector lever

 

3

RX port

5

Alphanumeric LEDs

 

2

TX port

 

4

Status LEDs

6

Ejector lever

 

Table 7 summarizes the optics and connectors used by the 1-Port 10-Gigabit Ethernet line card.

Table 7 1-Port 10-Gigabit Ethernet Line Card Optics and Connector Types

Part Number

Optics/Transmission

Maximum Distance

Connector Type

 

 

 

 

1X10GE-LR-SC

1550 nm (send),

20 km

SC

 

1300 nm-1570 nm (receive)

 

 

 

 

 

 

1X10GE-ER-SC

1550 nm (send),

75 km

SC

 

1300 nm-1570 nm (receive)

 

 

 

 

 

 

For more information, refer to the “10-Gigabit Ethernet” section on page 49 and the “Cabling and Specifications” section on page 41 .

The 1-Port 10-Gigabit Ethernet line card ships with 256 MB of route processor memory and 512 MB of packet memory. The memory in the 1-Port 10-Gigabit Ethernet line card is not field replaceable. For more information on memory, see the “Line Card Memory” section on page 64 .

Preparing for Installation

The following sections provide information about preparing to install line cards:

•Safety Guidelines, page 9

•Preventing Electrostatic Discharge, page 9

Cisco XR 12000 Series Router Ethernet Line Card Installation

8

OL-7861-01

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Contents Router Hardware Installation Important InformationEthernet Line Card Product Numbers Supported PlatformsLine Card Required Part Number Minimum IOS Software Release Hardware VersionProduct Overviews Memory OptionsRelated Documentation Ethernet Line Card ComparisonPort Gigabit Ethernet ISE Line Card Part NumberPort 1-Gigabit Ethernet Line Card Link Active RX Frame Preparing for Installation Port 10-Gigabit Ethernet Line CardSafety Guidelines Preventing Electrostatic DischargeRequired Tools and Equipment Removing and Installing a Line CardGuidelines for Line Card Removal and Installation Removing a Line Card Line Card Removal and Installation Installing a Line Card Ejector Levers Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line CardRemoving an EPA Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPAMating the Connector of the EPA to the Line Card Push Push Press on the White Labels on the EPA Inserting and Tightening the Screw on the EPA Removing and Installing GBICs Inserting the 2 screws on the Faceplate of the Line CardGeneral Gbic Handling and Maintenance Guidelines Removing the Gbic from an Ethernet Line CardInserting a Gbic into the Gigabit Ethernet Interface Removing and Replacing a GbicRemoving and Installing SFP Modules Bale Clasp SFP ModuleRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP ModuleRemoving a Mylar Tab SFP Module Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Installing an Actuator Button SFP Module Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Removing a Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Line Card Cable-Management BracketSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet InterfaceRJ-45 SC-TypeGbic Laser Optical Transceiver Modules Gbic Module Distance Connector Type Wavelength Fiber TypeGigabit Ethernet Interface Budget PowerTransmit Receive Link Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line Card Gbic Product Number Cwdm Gbic Wavelength Color IdentifierGeneral Cwdm Gbic Installation and Usage Guidelines Gigabit Ethernet SFP Modules Card carrier side of line cardSFP Module Type Wavelength Cable Distance Power Transmit Receive Typical MaximumTransceiver Budget Power Transceiver Option Type Wavelength Fiber-Optic Interface CablesGigabit Ethernet SC cable connector Spring-action disconnect latch Removing and Installing Fiber-Optic Interface Cables Simplex LC Cable ConnectorRemoving Fiber-Optic Interface Cables Installing Fiber-Optic Interface Cables Disconnecting Line Card Interface CablesTX connector Simplex cables RX connector Duplex cable Cleaning Fiber-Optic Connectors Removing RJ-45 Cables Removing and Installing RJ-45 100BASE-T Copper CableType RJ-45 100BASE-T Copper Cables Installing RJ-45 Cables Verifying and Troubleshooting the InstallationInitial Boot Process Status LEDs Gigabit Ethernet Status LEDsAlphanumeric LEDs Color/Activity DescriptionLED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Ethernet Line Card Hardware Engine Line Card MemoryLine Card Memory Locations Engine 2 Line Card Memory Locations ISE Line Card Memory LocationsISE Line Card Memory Locations Cisco Product Number Dimm Module Engine 4 Line Card Memory LocationsEthernet Line Card Route Memory Options Cisco Product Number Dimm Modules Dimm Sockets Removing and Installing Line Card MemoryEthernet Line Card Packet Memory Options Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Handling a DimmRemoving a Sodimm Remove Retaining Clip from Memory Module Socket Installing a Sodimm Moving the Plastic Latch Away from the SodimmSodimm Socket Retaining Clip Inserting a 144-pin Sodimm Module Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Completely Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe EUClass a Notice for Hungary Vcci Class a Notice for JapanLaser Safety Class a Notice for KoreaObtaining Documentation Cisco.comDocumentation DVD Ordering DocumentationCisco Product Security Overview Reporting Security Problems in Cisco ProductsDocumentation Feedback Cisco Technical Support Website Submitting a Service RequestObtaining Technical Assistance Definitions of Service Request Severity Obtaining Additional Publications and InformationObtaining Additional Publications and Information Obtaining Additional Publications and Information OL-7861-01

OL-7861-01 specifications

Cisco Systems OL-7861-01 is a robust and versatile device designed to meet the demands of modern networking environments. As part of Cisco's extensive portfolio of networking and communication solutions, the OL-7861-01 is tailored for organizations seeking high performance and reliability. The device is primarily deployed in voice over IP (VoIP) solutions, effectively enhancing communication capabilities across various sectors.

One of the standout features of the OL-7861-01 is its support for the latest VoIP technologies. This functionality allows organizations to implement efficient and cost-effective communication systems. Users benefit from crystal-clear voice quality, reduced latency, and improved overall user experience during calls. The device is equipped with advanced codecs, including wideband audio support, ensuring high-definition voice clarity.

In terms of enterprise readiness, the OL-7861-01 boasts seamless integration with Cisco’s Unified Communications Manager, enabling centralized management of communication systems. This integration simplifies deployment and management, allowing administrators to monitor system performance and access a range of administrative tools. Additionally, the device supports full duplex communication, ensuring that users can speak and listen simultaneously without interruptions.

The OL-7861-01 stands out with its robust security measures, which are crucial for protecting sensitive information during transmissions. It incorporates features such as secure RTP (SRTP) and transport layer security (TLS) to safeguard voice data against unauthorized access. This encryption capability is vital for organizations handling confidential communications.

The technological architecture of the OL-7861-01 is designed for scalability and flexibility. Organizations can easily expand their communication capabilities by integrating additional devices or users without significant infrastructure changes. This feature is essential for businesses anticipating growth or needing to adapt to changing communication demands.

Another notable characteristic of the OL-7861-01 is its user-friendly interface. The device is designed with an intuitive layout, allowing users to navigate features effortlessly. Coupled with customizable settings, end-users can tailor their communication experience to suit specific needs.

In summary, Cisco Systems OL-7861-01 is a powerful networking solution that brings together advanced VoIP capabilities, robust security features, and seamless integration with Cisco's communication ecosystem. Its scalability and user-friendly design make it an ideal choice for organizations looking to enhance their communication systems and improve overall productivity.
Top Page Image Contents