Cisco Systems 545 Serial manual Cisco Unified Videoconferencing 3545 PRI Gateway RTM

Page 22

Chapter 2 Installing the Cisco Unified Videoconferencing 3545 Gateway

Physical Description

Figure 2-1 Gateway Front Panel

 

SERIAL

GK Reg CD

 

 

 

 

 

157269

10/100Base T-1

RST

ALARM ACT

RDY

 

 

 

SWAP

 

Table 2-1

Front Panel Components

 

 

 

Component

 

Description

 

 

10/100 Base T-1

An RJ-45 connector that provides the primary Ethernet connection for the IP

connector

 

network port.

 

 

SERIAL connector

A DB-9 connector that allows you to connect a PC terminal for local

 

 

configuration.

 

 

 

RST button

 

Allows you to reset the gateway manually.

 

 

 

GK Reg LED

 

Lights green when the gateway is registered with a gatekeeper.

 

 

 

CD LED

 

Lights green when at least one gateway port connection is online.

 

 

 

ACT LED

 

Lights green to indicate that there are active calls in the gateway.

 

 

 

ALARM LED

 

Lights green to indicate that an error has occurred and the gateway requires

 

 

resetting.

 

 

10/100 Base T-1 LEDs

The top part of the 10/100 Base T-1 connector contains two LED indicators.

 

 

The left-hand LED lights green when the local IP network link is active. The

 

 

right-hand LED lights green if the connection speed is 100 Mbps, and is off

 

 

when the connection speed is 10 Mbps.

 

 

SWAP RDY LED

Hot Swap indication. Lights blue when the latches of a board are unlocked

 

 

and it is safe to remove the board from the chassis. Goes off when the board

 

 

is completely detached.

 

 

 

Cisco Unified Videoconferencing 3545 PRI Gateway RTM

The Rear Transition Module (RTM) provides the PRI line connections for the Cisco Unified

Videoconferencing 3545 PRI Gateway.

Figure 2-2shows the RTM panel components of the Cisco Unified Videoconferencing 3545

PRI Gateway module. Table 2-2describes these components.

Figure 2-2 PRI Gateway: Rear Transition Module

ACT

ACT

D-Ch

D-Ch

ALARM

ALARM

PORT-2

PORT-1

Table 2-2 PRI Gateway Rear Transition Module Components

157272

 

 

 

 

Component

Description

 

 

 

 

 

 

 

 

 

 

ACT LEDs

Lights green to indicate that there are active calls in the gateway.

 

 

 

 

 

 

 

 

 

 

D-Ch LEDs

Lights green to indicate that the PRI line is enabled and a carrier signal is

 

 

 

 

 

detected.

 

 

 

 

 

 

 

 

 

Installation and Upgrade Guide for Cisco Unified Videoconferencing 3545 PRI Gateway and 3545 Serial Gateway Release 5.5

 

 

 

 

 

 

 

 

 

 

 

2-2

 

 

 

OL-14912-01

 

 

 

 

 

 

Image 22
Contents Americas Headquarters Customer Order Number Text Part Number OL-14912-01Page N T E N T S Isdn Port Elektrische Sicherheit OL-14912-01 Functionality About the Cisco Unified Videoconferencing 3545 PRI GatewayFeature Description About Gateway FeaturesTCS4 Functionality Cisco Gateway Feature Specifics VGA, XGA, SVGA, SIF, 4SIF, CIF, QCIF, 4CIF, 16CIF Cisco Gateway Feature Specifics About Multimedia Conferencing Multimedia Conferencing through the GatewayAbout Point-to-Point Conferencing About Multipoint ConferencingAbout Gateway IP Network Connections About Gateway Isdn Network ConnectionsPRI Gateways About Gateway Encryption Encrypted VideoconferencingAbout Conferencing via Leased Lines About IP-to-Legacy MCU ConferencingAbout PRI Gateway Call Handling Capacity About Gateway Call Bandwidth OverheadResource Allocation across E1/T1 Lines About Peer-to-Peer ConnectivityPhysical Description Installing the Cisco Unified Videoconferencing 3545 GatewayGateway Module Cisco Unified Videoconferencing 3545 PRI Gateway RTM Component DescriptionPreparing for Installation Cisco Unified Videoconferencing 3545 Serial Gateway RTMVerifying the Package Contents Procedure Related TopicsInstalling the Gateway Before You BeginInstalling the RTM Module Installing the Gateway Module Removing a Module Initial Gateway Configuration Connecting to a PCSetting the IP Address RequirementsChanging the Configuration Tool Login Password Network configuration Main menu displaysUpgrading Gateway Software Click OKConnecting PRI Lines to the Gateway Connecting the Gateway to the NetworkConnecting Serial Lines to the Gateway Serial Gateway Cable Connections and Pin-outs Physical Description of DTE Cables35/RS366-DTE EIA530/RS366-DTE-LOS EIA530A/RS366-DTE Physical Description of DCE Cables 35/RS366-DCEEIA449/RS366-DCE Data Interface Cable Pin-out Configurations EIA-449 DB-37 EIA-530 DB-25 35 M-34Connector Data Interface Pin LayoutsDB-37 Connector DB-25 Connector 18shows the DB-25 pin layoutSignaling Interface Cable Pin-out Configuration Signaling Interface Pin Layout DB-25 ConnectorConnecting the Gateway to a Power Source Accessing the Gateway Administrator InterfaceRegistering the Online Help Netscape Navigator UsersLaunching the Cisco Software Upgrade Utility Using the Cisco Software Upgrade UtilityIntroduction Click Customize Snmp Settings Upgrading SoftwareUnit RS-232 9-Pin Serial Port Cable Connections and Pin-outsPin Function TXD+ Pin Serial Port Terminal CableRJ-45 8-Pin IP Network Port RXD+RXD + Circuit Switch Network PortIsdn Port TXD +OL-14912-01 Technical Specifications Technical Specifications TablePush Buttons Board LED IndicatorsCommunication Interfaces Operating System Power supplyChipset MemoryOL-14912-01 Electrical Safety SafetyGrounding Power Supply ESD ProceduresHigh Voltage Erdung SicherheitElektrische Sicherheit HochspannungESD-Verfahren WarnhinweiseTierra SeguridadSeguridad Electrica Alto VoltageProcedimientos ESD Securite Electrique SecuriteMise a la Terre Haute Tension Prevention des Decharges ElectrostatiquesAlimentation Electrique Safety Compliance Compliance and CertificationsCISPR24 TelecomFCC Part 15 Notice CE CTR3 CE CTR4Acta Customer Information Canadian Department of Communications NoticeEnvironmental Compliance DTE DCEDid E1/T1 EIA-530 IsdnPRI IN-3Snmp