Fujitsu Siemens Computers S2110 Exit Menu - Leaving The Setup Utility, Menu Field, Description

Page 27
E x i t M e n u

E x i t M e n u

EXIT MENU – LEAVING THE SETUP UTILITY

The Exit Menu is used to leave the setup utility. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See Navigating Through the Setup Utility on page 2 for more information). The following table shows the names of the menu fields for the Exit menu, the default settings and a description of the field's function and any special information needed to help understand the field's use.

PhoenixBIOS Setup Utility

Main

Advanced

SecurityBootExit

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Discard Changes

Save Changes

Save Changes and Power Off

Item Specific Help

Exit System Setup and save your changes to CMOS.

F1 Help

Select

Item

-/SpaceChange Values
ESC Exit

Select

Menu

Enter

Select ▲ Sub-Menu

Figure 18. Exit Menu
F9 Setup Defaults

F10 Save and Exit

Table 18: Fields, Options and Defaults for the Exit Menu

Menu Field

Description

 

 

 

 

Exit Saving

Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory and

Changes

then exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes]

 

[No] will be displayed.

 

 

Exit Discarding

Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the

Changes

BIOS recognizes this selection it will load the operating system and begin operation.

 

 

Load Setup

Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message

Defaults

Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit

 

Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.

 

 

Discard Changes

Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load

 

previous now? [Yes] [No] will be displayed. When confirmed the utility will return to the Exit menu. To

 

return to another menu, follow the directions in the Navigating Through the Setup Utility Section.

 

 

Save Changes

Selecting Save Changes causes the new settings in all menus to be written to the BIOS memory. The message Save

 

configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return

 

to the Exit menu. To go to another menu, follow the directions in the Navigating Through the Setup Utility section.

 

 

Save Changes

Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the BIOS memory,

and Power Off

then power the system off. The message Save configuration changes now and power off? [Yes]

 

[No] will be displayed. When confirmed, the setup utility shut down the system.

 

 

27

Page 26 Page 27
Image 27
Page 26 Page 27
Contents F U J I T S U C O M P U T E R S Y S T E M S BIOS GuideFujitsu LifeBook S Series LifeBook S Series Model S2110S Series BIOS BIOS SETUP UTILITYEntering the BIOS Setup Utility Navigating Through the Setup UtilityM a i n M e n u Warning! Error message ContinueTable 1 Fields, Options and Defaults for the Main Menu MAIN MENU - SETTING STANDARD SYSTEM PARAMETERSOptions Auto Primary Master Submenu of the Main MenuA bootable DVD/CD-ROM may have either a floppy disk or hard drive format. When the bootable DVD/ CD-ROM is used, the drive allocations change automatically without changing the BIOS setup. If a floppy disk format DVD/CD-ROM is used, the DVD/CD-ROM becomes Drive A. The DVD/CD-ROM will only take drive C hard drive format if the internal hard drive is not present or is disabled. The bootable DVD/ CD-ROM can never use a C designation if a formatted internal hard drive is present since the C designa- tor is always reserved for the internal hard drive.The boot sequence ignores the new drive designations, however, your application software will use the new designations Secondary Master Submenu of the Main Menu Exiting from Main Menu ADVANCED MENU - SETTING DEVICE FEATURE CONTROLS A d v a n c e d M e n u Table 4 Fields, Options and Defaults for the Advanced MenuEnabled Serial/Parallel Port Configuration Submenu of the Advanced MenuOptions PhoenixBIOS Setup Utility Keyboard/Mouse Features Submenu of the Advanced MenuPower Savings Internal Pointing Device Auto DisabledMain Video Features Submenu of the Advanced MenuInternal Device Configurations Submenu of the Advanced Menu Figure 9. USB Features Submenu USB Features Submenu of the Advanced MenuUSB Features The feature is disabledDisabled Miscellaneous Configurations Submenu of the Advanced MenuEvent Logging Submenu of the Advanced Menu Figure 12. Security Menu SECURITY MENU - SETTING THE SECURITY FEATURESS e c u r i t y M e n u Table 12 Fields, Options and Defaults for the Security MenuAdvanced Hard Disk Security Submenu of the Security MenuEnter Owner Information Submenu of the Security MenuExiting from the Security Menu ESC ExitTable 15 Fields, Options and Defaults for the Boot Menu BOOT MENU - SELECTING THE OPERATING SYSTEM SOURCEExiting from Boot Menu The Boot Device Priority Submenu of the Boot MenuINFO MENU - DISPLAYS BASIC SYSTEM INFORMATION Table 17 Fields, Options and Defaults for the Info MenuExit Saving Changes Exit Discarding Changes Load Setup Defaults EXIT MENU - LEAVING THE SETUP UTILITYTable 18 Fields, Options and Defaults for the Exit Menu Boot
Top Page Image Contents