Cisco Systems MWR 1900 manual Fast Ethernet Interfaces, Voice/WAN Interface Cards

Page 14

Chapter 1 Overview of the Cisco MWR 1900 Router

Fast Ethernet Interfaces

•Redundancy support via a two T1/E1 WIC capable of port switching ON/OFF via relays

•Console RS-232 port

•Auxiliary Serial Port with hardware flow control

•Extended operational temperature range from -10ºC to + 55ºC with over-temperature sensor

•Front (connector side) to rear airflow using four 40mm, 10 CFM exhaust fans

•Custom +27V DC input power

•Three green chassis LEDs for Power (PS is operational), System Ready (software is up and running), and Activity (interrupts/packet transfers running)

•One Network Module slot (for future use)

Fast Ethernet Interfaces

The MWR 1900 router has two fixed LAN ports offering 10/100 Base-T Ethernet attachment. The ports are fully compliant with the IEEE 802.3 and 802.3U standards and integrate the media access control (MAC) functions and a dual-speed MII interface. Both ports can operate in half- or full-duplex mode and can run independently of one another. For each FE interface, there are two green LEDs, one for Link Integrity and one for Link Activity.

Voice/WAN Interface Cards

The Cisco VWIC-2MFT-T1-DIR and VWIC-2MFT-E1-DIR Voice/WAN Interface Cards support data applications on the Cisco MWR 1900 Mobile Wireless Edge Router for T1/E1 networks. These cards are dual-port, T1/Fractional T1 or E1/Fractional E1, Drop and Insert Multiplexers with integrated T1 CSU/DSUs or E1 DSUs. The T1 version supports framed and unframed traffic, and the E1 version supports framed traffic and unframed traffic that conforms to the ITU-T G.703 standard for full 2.048 Mbps bandwidth.

The Drop and Insert multiplexer diverts (drops) streams of an aggregate Time Division Multiplexed (TDM) traffic stream, and introduces (inserts) different streams for transmission in the time slots that were previously occupied by the dropped streams. Each VWIC supports a limited channelized capability where the T1 or E1 can be flexibly split into two fractional channel groups, one on each port or two on one port. The switching operation can be maintained through router restarts and reloads of Cisco IOS software.

Each card also features protection switch solid state relays on the line interfaces, which together with redundancy logic and relay control added to the base Cisco IOS feature set on the MWR 1900, provides T1/E1 Protection Switching between redundant routers.

The MWR 1900 router provides two WAN interface slots, which allows support for 4 T1/E1s. A third WAN interface slot is reserved for future use.

Additional information is contained in separate publications that accompanied your router package.

•For information on Voice/WAN interface cards (VWICs), see the publication VWIC-2MFT-T1DIR,VWIC-2MFT-E1DIR Installation Instructions.

•For software configuration information, see the publication Cisco MWR 1900 Software Configuration Guide.

These manuals are on Cisco.com. See “Obtaining Documentation” for more information.

Cisco MWR 1900 Mobile Wireless Edge Router Hardware Installation Guide

1-4

78-13982-02

 

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Corporate Headquarters Customer Order Number DOC-7813982= Text Part NumberCopyright 2002 Cisco Systems, Inc All rights reserved Safety Recommendations Safety with Electricity Hardware FeaturesPreparing to Install the Router Obtaining DocumentationConsole Port Connections What to Do After Installing the HardwareProblem Solving Console PortOrganization ObjectivesAudience Chapter Title DescriptionConventions Convention DescriptionAvvertenza Määräysten noudattaminen ja tietoa turvallisuudestaWarnung Questo dispositivo¡Advertencia Varning Obtaining DocumentationWorld Wide Web Documentation Feedback Obtaining Technical AssistanceOrdering Documentation Cisco.comContacting TAC by Telephone Contacting TAC by Using the Cisco TAC WebsiteTechnical Assistance Center Overview of the Cisco MWR 1900 Router Primary Use of the MWRHardware Features MWR 1900 in an IP-RAN SolutionFront Panel of the Cisco MWR 1900 Router Fast Ethernet Interfaces Voice/WAN Interface CardsCompact Flash Overview of Cisco MWR 1900 Power SuppliesSpecification Description Specification Environmental Monitoring Temperature SensorSystem Specifications Regulatory CompliancePreparing to Install the Router Safety RecommendationsSafety with Electricity General Site Requirements Inspecting the Router Creating a Site LogInstallation Checklist Task Verified by DateAuxiliary Port Connections Console and Auxiliary Port ConsiderationsConsole Port Connections Installing the Router Rack Mounting the ChassisInstalling a T1/E1 Multiflex Vwic Connecting the Console Terminal and ModemInstalling the Router in the Rack Attaching the BracketsIdentifying a Rollover Cable Console PortAuxiliary Port Connecting the Network CablesConnecting the FE Interface Cables Connecting the Vwic Interface Cables Pin DescriptionCable Specifications PinConnecting the MWR 1900 Router to a DC-Input Power Supply Required Tools and EquipmentGrounding the Router Wiring the DC-Input Power Source Powering On the RouterReplacing or Upgrading the CF Installing a CF Memory Card in an External Slot Removing a CF Memory Card from an External SlotFormatting CF Memory as a DOS File System Formatting Procedures for CF Memory CardsFile and Directory Procedures Copy FilesDisplay the Contents of a CF Card Display Geometry and Format InformationDelete Files from Flash Rename a File in FlashDisplay File Content Create a New DirectoryEnter a Directory and Determine the Current Directory What to Do After Installing the HardwareRemove a Directory Troubleshooting Problem SolvingTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesTroubleshooting Modules, Cables, and Connections Reading the LEDsColor Status Carrier detect GColor Description Page Numerics IN-2 IN-3 IN-4
Top Page Image Contents