Billion Electric Company 7402VL user manual Connection, Advanced Options PPPoE, Configuration

Page 47
Advanced Options (PPPoE)

VoIP/(802.11g) ADSL2+ Router

Authentication Protocol: Default is Chap(Auto). Your ISP will advise you whether to use Chap or Pap.

Connection:

Always on: If you want the router to establish a PPPoE session when starting up and to automatically re-establish the PPPoE session when disconnected by the ISP.

Connect to Demand: If you want to establish a PPPoE session only when there is a packet requesting access to the Internet (i.e. when a program on your computer attempts to access the Internet).

Idle Timeout: Auto-disconnect the broadband firewall gateway when there is no activity on the line for a predetermined period of time.

Detail: You can define the destination port and packet type (TCP/UDP) without checking by timer. It allows you to set which outgoing traffic will not trigger and reset the idle timer.

RIP: RIP v1, RIP v2, and RIP v2 Multicast. Check to enable RIP function.

MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface.

Advanced Options (PPPoE)

LLC Header: Selects encapsulation mode, true for using LLC or false for using VC-Mux.

Create Route: This setting specifies whether a route is added to the system after IPCP (Internet Protocol Control Protocol) negotiation is completed. If set to enabled, a route will be created which directs packets to the remote end of the PPP link.

Specific Route: Specifies whether the route created when a PPP link comes up is a specific or default route. If set to enabled, the route created will only apply to packets for the subnet at the remote end of the PPP link. The address of this subnet is obtained during IPCP negotiation.

Subnet Mask: sets the subnet mask used for the local IP interface connected to the PPP transport. If the value 0.0.0.0 is supplied, the netmask will be calculated from the class of the IP address obtained during IPCP negotiation.

Route Mask: Sets the subnet mask used by the route that is created when a PPP link comes up. If it is set to 0.0.0.0, the subnet mask is determined by the IP address of the remote end of the link. The class of the IP address is obtained during IPCP (Internet Protocol Control Protocol) negotiation.

MRU: Maximum Receive Unit. This is negotiated during the LCP protocol stage.

Discover Primary / Secondary DNS: This setting enables/disables whether the primary/secondary DNS server address is requested from a remote PPP peer using IPCP. The default setting for this command is enabled.

Give DNS to Relay: Controls whether the PPP Internet Protocol Control Protocol (IPCP) can request the DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS server IP address, it automatically gives the address to the local DNS relay so that a connection can be established.

Give DNS to Client: Controls whether the PPP Internet Protocol Control Protocol (IPCP) can request a DNS server IP address for a remote PPP peer. Once IPCP has discovered the DNS

46

Chapter 4:Configuration

Page 46 Page 48
Image 47
Page 46 Page 48
Contents User’s Manual Version ReleaseBiPAC 7402VL/VGL/VGP VoIP/802.11g ADSL2+ RouterCHAPTER 1 INTRODUCTION CHAPTER 2 INSTALLING THE ROUTERCHAPTER 3 BASIC INSTALLATION CHAPTER 4 CONFIGURATIONQoS Quality of Service CHAPTER 5 TROUBLESHOOTINGAPPENDIX A PRODUCT SUPPORT AND CONTACT INFORMATION Firewall and Access ControlModels FeaturesChapter 1 Introduction Introduction to your RouterUniversal Plug and Play UPnP and UPnP NAT Traversal Quick Installation WizardQuality of Service QoS Multi-Protocol to Establish A ConnectionStatic and RIP1/2 Routing Dynamic Host Configuration Protocol DHCP client and serverFirmware Upgradeable Rich Packet FilteringDo not use the same power source for this router as other equipment Chapter 2 Installing the RouterImportant note for using this router Package ContentsRJ-11 connector The Front LEDsMeaning RJ-45 connector7402VGP The Rear Ports7402VL 7402VGLMeaning Port 1 Power Switch 2 PWR 3 RESET LAN 4 1X - 3X RJ-45 connector5 CONSOLE Phone 6 1X 2X RJ-11 connector 7 ADSL 8 Antenna 7402VGL/VGP onlyCabling Chapter 3 Basic Installation Chapter 3 Basic Installation7402VGP Connecting your router7402VL/VGL 4. Select Internet Protocol TCP/IP and click Properties. See Figure Configuring PCs in Windows in Window XPFigure 3.3 TCP / IP Figure 3.4 IP Address & DNS Configuration 2. Double-click Local Area Connection. See FigureFigure 3.5 LAN Area Connection Configuring PCs in WindowsFigure 3.8 IP Address & DNS Configuration 2. Double-click Local Area “LAN” Connection. See Figure3. Click Properties Figure 3.9 TCP / IP Configuring PC in Windows 95/98/ME5. Then select the DNS Configuration tab. See Figure Figure 3.11 DNS ConfigurationFigure 3.13 IP Address Configuring PC in Windows NT4.02. Select TCP/IP Protocol and click Properties. See Figure Figure 3.12 TCP / IPISP setting in WAN site Factory Default SettingsWeb Interface Username and Password LAN Device IP SettingsPPPoE PPPoA RFC1483 Bridged RFC1483 Routed IPoA Information from your ISPFigure 3.14 User name & Password Prompt Widonw Configuring with your Web BrowserSave Config to FLASH Chapter 4 ConfigurationQuick Start Configuration ARP Table Wireless Association Table 7402VGL/VGP onlyStatus RIP Routing Table Routing TableRouting Table Permanent Table DHCP TableLeased Table Expired TableEvent Log Email StatusVoIP Status UPnP Portmap Error LogNAT Sessions Quick Start VoIP/802.11g ADSL2+ Router Ethernet ConfigurationLAN Local Area Network Ethernet Client Filter Ethernet Client Filter Default setting is set to DisableActive PC in LAN displays a list of individual Ethernet device’s IP Address & MAC Address which connecting to the router Parameters EnableWireless Distribution System WDS Wireless Security 7402VGL/VGP only WPA Pre-Shared KeyPage →Associated Wireless Clients Wireless Client MAC Address Filter 7402VGL/VGP onlyAssociate Wireless Client displays a list of individual wireless device’s MAC Address that currently connects to the router DHCP Server WAN Wide Area Network RFC 1483 Routed Connections Pppoe RFC 1483 Bridged ConnectionsPPPoA Routed Connections Advanced Options PPPoA ConnectionGive DNSto DHCP Server Similar to the above, but gives the DNS server address to the DHCP server IPoA Routed Connections PPPoE Connections Advanced Options PPPoE VoIP/802.11g ADSL2+ Router Chapter 4ConfigurationPage ADSL Time Zone SystemRemote Access Firmware Upgrade Backup / Restore Restart Router User Management Firewall and Access Control General Settings Packet Filter Protocol Example Predefined Port Filters RulesTable 1 Predefined Port Filter ApplicationPacket Filter - Add TCP/UDP Filter Packet Filter - Add Raw IP Filter Page 3. Click Add TCP/UDP Filter Click DeleteClick Add TCP/UDP Filter Configuring Packet Filter5. The new port filter rule for HTTP is shown below Block Duration Intrusion DetectionAscend Kill Table 2 Hacker attack types recognized by the IDSIntrusion Name Detect ParameterURL Filter Domains Filtering This function checks the domain name only, not the IP address, in URLs accessed against your list of domains to block or allow. If it is matched, the URL request will be sent Trusted or dropped Forbidden. For this function to be activated, both check-boxes must be checked. The checking procedure is Restrict URL Features This function enhances the restriction to your URL rules Log information can be seen in the Status - Event Log after enabling Firewall LogPSTN Dial Plan VoIP Voice over Internet ProtocolWizard Authentication Username Same as Phone NumberPlease refer to the description of “Setting for Phone Port 1” Setting for Phone PortSIP Device Parameters General ConfigurationRegistrar Port from VoIP device Authentication Username Same as Phone Number Phone ConfigurationLogin Account Configuration For examples Codec PreferenceSpeed Dial Dial without Prefix Dial only the Number of Digits and not the prefix ActionFor Example automatically Power downInternet Service fail SIP service is not available74xnumber# OptionDescription Flash-hookQoS Quality of Service High PrioritizationDSCP Mapping Table Wireless ADSL RouterTable 4 DSCP Mapping Table Standard DSCPOutbound IP Throttling LAN to WAN Inbound IP Throttling WAN to LAN Information and Settings Example QoS for your NetworkVoIP Normal PCs Restricted Connection DiagramRestricted Application Mission-critical applicationVoice application Advanced setting by using IP throttling Virtual Server “Port Forwarding” Add Virtual Server IP Address Application HTTPSever Time Schedule Always On Protocol tcpEdit DMZ Host Global IP Address Edit One-to-One NAT Network Address TranslationSelect the Apply button to apply your changes Protocol Example List of some well-known and registered port numbersTable 5 Well-known and registered Ports Port NumberTime Schedule Configuration of Time Schedule Edit a Time SlotDelete a Time Slot Click EditStatic Route AdvancedDynamic DNS Check Email Embedded Web Server Device ManagementSNMP SNMP Version SNMPv2c and SNMPv3Universal Plug and Play UPnP SNMP V1 andFrom RFC 1471 PPP/LCP MIB From RFC 1213 MIB-IIFrom RFC1650 EtherLike-MIB From RFC 1493 Bridge MIBFrom RFC1695 atmMIB From RFC 1473 PPP/IP MIBFrom RFC 1474 PPP/Bridge MIB From RFC1573 IfMIBIGMP Save Configuration to Flash Logout Problem Chapter 5 TroubleshootingProblems starting up the router Problems with the WAN InterfaceCan’t ping any PCs on the LAN Problems with the LAN InterfaceWORLDWIDE APPENDIX A Product Support and Contact InformationContact Billion AUSTRALIA
Top Page Image Contents