Cisco Systems IAD2430 manual Product Serial Number Location, Xiv

Page 14

Preface

Product Serial Number Location

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool. Statement 1035

Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036

Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037

Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Statement 1038

Warning To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260. Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The telecommunications lines must be disconnected 1) before unplugging the main power connector or 2) while the housing is open, or both. Statement 1043

Product Serial Number Location

The serial number label for the Cisco IAD2430 series routers (Cisco IAD2430 through Cisco IAD2432) is located on the back of the chassis, near the compliance label. The size of the serial number label is

0.25x 1 inch (0.635 x 2.54 centimeters). It has the letters “SN:” followed by eleven characters. (See Figure 0-1.) The serial number label for the Cisco IAD2435 series IAD is located on the bottom of the chassis, near the compliance label. (See Figure 0-2.)

Cisco IAD2430 Series Integrated Access Devices Hardware Installation Guide

 

xiv

OL-4234-06

 

 

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Americas Headquarters Text Part Number OL-4234-06Copyright 2003 2008 Cisco Systems, Inc. All rights reserved N T E N T S Safety Tips Cable Connecting to a Remote PC Chapter Title Description AudienceOrganization Convention Description Safety WarningsConventions Waarschuwing Belangrijke Veiligheidsinstructies Hinweis Bewahren SIE Diese Sicherheitsanweisungen AUFOBS! Spara Dessa Anvisningar Page Guarde Estas Instruções Xiii Product Serial Number Location XivAccessibility Serial Number Location on Cisco IAD2430 Series RoutersRelated Documentation Cisco Product Document Title and URLOverview of Cisco IAD2430 Series IADs OverviewCisco IAD2430 Series IADs Front Panel Cisco IAD2430-24FXS IAD Cisco IAD2431-8FXS IADCisco IAD2431-16FXS Cisco IAD2431-1T1E1 IADCisco IAD2432-24FXS IAD Cisco IAD2435-8FXS IADPhysical Description Cisco IAD2435-8FXS ChassisLEDs 10 Cisco IAD2435 Series IAD Back Panel Function OptionsLED/Color Description Cisco IAD2435 Series LEDsPort Numbering Conventions Chassis GroundingMemory LED/Color LED Color and DescriptionConfiguration Methods SpecificationsConfiguration Connections Software ElementsInterfaces and Service Capabilities Manual ConfigurationWAN Cisco IAD2430 Series RJ-21 T1/E1 Configuration OptionsDeployment Options T1/E1 with T1/E1 Interface to PBX Temperature Control and Ventilation Location and Mounting RequirementsChassis Grounding Access to ChassisPower Source Cable Types EIA/TIA-530/EIA/TIA-530A DCE/DTEFast Ethernet Maximum Distance Signal Rate Distance Feet Distance MetersDistance Limitations for Interface Cables T1/E1-WAN Port Maximum DistancesEIA/TIA-449, V.35, and X.21 Speed and Distance Limitations FXS Analog Voice Port Maximum Distance Interference ConsiderationsT1/E1-PBX Digital Voice Port Maximum Distances FXO Analog Voice Port Maximum DistanceInstalling Cisco IAD2430 Series IADs General Safety Practices Safety RecommendationsMaintaining Safety with Electricity Safety TipsPreventing Electrostatic Discharge Damage Keeping Track-ChecklistSite Log Task Verified by Date Installation ChecklistMounting Tools and Equipment Unpacking and Inspection Quick Installation Bracket for Cisco IAD2435-8FXS Routers Rack-Mounting the ChassisMounting Screws Attaching the BracketsInstalling the Cisco IAD2430 Series IADs in a Rack Telco 19-Inch Rack Installation-Back Panel ForwardWall-Mounting the Chassis Attaching the Chassis to the 19-Inch Rack10shows the orientation required for installation Wall-Mounting the Cisco IAD2435 IADs 10 Wall-Mounting the ChassisRubber feet 12 Mounting the IAD2435 Router on a Wall Desktop-Mounting the Chassis Installing the Ground ConnectionSetting the Cisco IAD2435 on a Desktop Page To a torque of 8 to 10 in-lb 0.9 to 1.1 N-m Installing a WAN or Voice Card 16 Chassis Ground Connection Using Ring TerminalConnecting Cables Cisco IAD ports are color-coded for identificationConnected To Cable LAN and Power CablesNebs Tests Results 17 LAN and Administrative Access Connections Connecting the Input Power ProcedureConnecting the Console Port to a PC or an Ascii Terminal 19 Connecting the External Power Supply to the Cisco IAD2435Connecting the Auxiliary Port to a Modem WAN and Voice Cables Color or Type Connected To CableConnecting the RJ-21 Cable in the Velcro Harness 20 WAN and Voice Connections22 Sliding the RJ-21 Cable Through the Velcro Harness 24 Tightening the Captive Screws DTE only with EIA/TIA -530 signaling Use an RJ-48 T1/E1 cable not included Connecting the Digital Voice Port to a T1/E1-PBX Connect the RJ-48 T1/E1 cable to the T1/E1 port. See FigureRemote Terminal Connections If Applicable Ports, Connectors, and PinoutsCisco IAD Port Port Color Connector/Cable Interface To Connecting to a Remote Ascii Terminal Connecting to a ModemConnecting to a Remote PC Cisco IAD2430 Model Power Consumption Watts Connecting Backup PowerConnecting a Backup Battery to a DC-Powered IAD 30 Connecting a Backup Battery to a DC-Powered Cisco IAD Pin Number Description32shows a setup using a UPS OL-4234-06 Checklist for Power-On Power-On ProcedureInitial Configuration Procedures Cisco IOS CLI Press Return or Enter. The following message is displayedSetup Command Facility Configuration is displayed Obtaining Your Network Information Manual ConfigurationSetting the Fast Ethernet Port IP Address Configuring a T1/E1 Port for a WAN Connection Command PurposeConfiguring Digital Voice Verifying and Saving Your ConfigurationTroubleshooting NvramSymptom Possible Cause Corrective Action Numerics IN-2 IN-3 IN-4

IAD2430 specifications

Cisco Systems IAD2430 is a versatile Integrated Access Device (IAD) designed to deliver voice and data services to small and medium-sized businesses. This device plays a pivotal role in the convergence of voice and data networks, offering a comprehensive solution that simplifies management and enhances operational efficiency.

One of the most compelling features of the IAD2430 is its support for both traditional TDM (Time-Division Multiplexing) and VoIP (Voice over Internet Protocol) technologies. This dual capability enables businesses to migrate to IP-based voice solutions while still maintaining their existing TDM infrastructure. The IAD2430 is equipped with multiple built-in voice ports, allowing it to support a variety of telephony applications.

In terms of performance, the IAD2430 offers robust Quality of Service (QoS) features that prioritize voice traffic to maintain call clarity and reliability. This is particularly critical in environments where voice communication is essential for daily operations. QoS mechanisms ensure that voice packets are transmitted with minimal latency, jitter, and packet loss, providing an uninterrupted communication experience.

The IAD2430 also boasts advanced security features, including firewall protection and encrypted data transmission. This is particularly important for businesses looking to protect sensitive information and ensure compliance with industry regulations. The built-in security measures help safeguard against unauthorized access and potential threats, providing peace of mind to users.

Moreover, the device supports various WAN connections, including T1, DSL, and Ethernet, making it adaptable to different network environments. Its flexible connectivity options allow for seamless integration with existing network infrastructure while maximizing bandwidth utilization.

Management and configuration of the IAD2430 are simplified through a user-friendly web interface and support for remote administration. This allows IT staff to efficiently configure and monitor the device without the need for onsite visits, thus reducing operational costs.

In summary, the Cisco Systems IAD2430 stands out as a reliable and feature-rich IAD capable of catering to the needs of businesses that require integrated voice and data services. Its combination of TDM and VoIP support, enhanced QoS, robust security features, and flexible connectivity options make it an ideal choice for organizations looking to streamline their communication solutions.
Top Page Image Contents