Cisco Systems WRTP54G manual Router IP, Network Address Server Settings Dhcp

Page 28

Wireless-G Broadband Router with 2 Phone Ports

Router IP

The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work.

Local IP Address. The default value is 192.168.15.1.

Subnet Mask. The default value is 255.255.255.0.

Network Address Server Settings (DHCP)

These settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. Unless you already have one, it is highly recommended that you leave the Router enabled as a DHCP server.

Local DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, set the Router’s DHCP option to Disable. If you disable DHCP, remember to assign a static IP address to the Router.

Start IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the default IP address for the Router is 192.168.15.1, the Start IP Address must be 192.168.15. 101 or greater, but smaller than 192.168.15.254. The default Start IP Address is 192.168.15.100.

Number of Address (Optional). Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.

DHCP Address Range. The range of DHCP addresses is displayed here.

20

Chapter 5: Configuring the Router

 

The Setup Tab - Basic Setup

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Wireless- G Division of Cisco Systems, IncPage Copyright and Trademarks How to Use this GuideWord definition Wireless-G Broadband Router with 2 Phone Ports Table of Contents Appendix C Finding the MAC Address and IP Vonage 103 LinksysWireless Security Radius Wireless Security WEPWireless MAC Filter Wireless Security37 Dhcp Active IP Table Introduction WelcomeWhat’s in this Guide? Introduction What’s in this Guide? Wireless-G Broadband Router with 2 Phone Ports Planning Your Wireless Network Ad-Hoc versus Infrastructure ModeSsid your wireless network’s name Network TopologyNetwork Layout Getting to Know the Router Back PanelPower Front PanelConnecting the Router OverviewConnection Instructions Connect the ModemPlacement Options Stand OptionWall-Mount Option Measurement between Wall-Mount SlotsConfiguring the Router Wireless SetupSecurity Access Restrictions AdministrationApplications & Gaming StatusHow to Access the Web-based Utility VoiceSetup Tab Basic Setup Internet SetupInternet Connection Type Obtain an IP automaticallyStatic IP Optional Settings Network SetupPacket a unit of data sent over a network Network Address Server Settings Dhcp Router IPSetup Tab Ddns Time SettingDynDNS.org TZO.comSetup Tab MAC Address Clone MAC CloneSetup Tab Advanced Routing Advanced Routing10 Routing Table Entry List Wireless Tab Basic Wireless Settings Wireless SettingsWireless Tab Wireless Security Wireless Security13 Wireless Tab Wireless Security WPA-RADIUS 15 Wireless Tab Wireless Security WEP Wireless Tab Wireless MAC Filter Wireless MAC FilterWireless Tab Advanced Wireless Settings Advanced Wireless SettingsWireless-G Broadband Router with 2 Phone Ports Security Tab Firewall Web FiltersAccess Restrictions Tab Filter Filter IP Address RangeFilter Port Range Filter MAC AddressBlock WAN Requests Access Restrictions Tab Device Access Control Access ControlPort Range Forwarding Applications & Gaming Tab Port Range ForwardingPort Range Port Triggering Applications & Gaming Tab Port TriggeringTriggered Range UPnP Forwarding Applications & Gaming Tab UPnP ForwardingForwarded Range Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Applications & Gaming Tab DMZ DMZApplications & Gaming Tab QoS IP QoS29 QoS Create Rule Administration Tab Management Router PasswordLocal Router Access UPnPAdministration Tab Log LogAdministration Tab Factory Defaults 32 Administration Tab Factory DefaultsPing Test Administration Tab DiagnosticsTraceroute Test Status Tab Local Network Local NetworkStatus Tab Router InformationStatus Tab Router Status Tab Wireless 39 Status Tab WirelessLine1 Status Status Tab VoiceLine2 Status Voice Tab 42 Voice TabAppendix a Troubleshooting Common Problems and SolutionsFor Windows 98 and Millennium Need to set a static IP address on a PCFor Windows For Windows XPWant to test my Internet connection For Windows XP Wireless-G Broadband Router with 2 Phone Ports Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router Application Start and End Protocol IP Address Enabled TCPCan’t get the Internet game, server, or application to work Appendix a Troubleshooting Common Problems and Solutions To start over, I need to set the Router to factory default My DSL service’s PPPoE is always disconnectingFor Microsoft Internet Explorer 5.0 or higher For Netscape 4.7 or higherWireless-G Broadband Router with 2 Phone Ports Go through this checklist until your problem is solved Frequently Asked Questions Where is the Router installed on the network?How do I make a phone call? Can I make calls if my Internet connection is down?What is Network Address Translation and what is it used for? How can I block corrupted FTP downloads? What is DMZ Hosting? If all else fails in the installation, what can I do?Will the Router function in a Macintosh environment? What is the Ieee 802.11b standard? Is the Router cross-platform compatible?How many ports can be simultaneously forwarded? Which modems are compatible with the Router?What Ieee 802.11b features are supported? What is the Ieee 802.11g standard?What Ieee 802.11g features are supported? What is infrastructure mode? What is ad-hoc mode?What is roaming? What is Spread Spectrum? What is ISM band?What is DSSS? What is FHSS? And what are their differences? What is WEP? What is WPA?What is a MAC Address? How do I reset the Router?Have excellent signal strength, but I cannot see my network How many channels/frequencies are available with the Router?Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Figure C-1 IP Configuration Screen Windows 98 or Me InstructionsWindows 2000 or XP Instructions For the Router’s Web-based UtilityShared Resources Appendix D Windows HelpNetwork Neighborhood/My Network Places Appendix D Windows Help Appendix E Glossary Appendix E Glossary Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Wireless-G Broadband Router with 2 Phone Ports Appendix F Specifications Operating Humidity Warranty Year LimitedStorage Humidity Appendix G Warranty Information Limited WarrantyAppendix G Warranty Information Appendix H Regulatory Information Federal Communication Commission Interference StatementImportant Note 101 Safety Notices Appendix I Contact Information VonageLinksys Need to contact Vonage?Linksys

WRTP54G specifications

Cisco Systems is a prominent name in the realm of networking and communication technology, and one of its notable offerings is the WRTP54G, a versatile wireless router designed to enhance home and small office networks. With its dual functionality as both a router and a VoIP (Voice over Internet Protocol) gateway, the WRTP54G stands out by combining traditional internet access with advanced voice communication capabilities.

One of the main features of the WRTP54G is its robust wireless connectivity. It complies with the IEEE 802.11g standard, providing high-speed wireless connections of up to 54 Mbps, which is ideal for streaming media, online gaming, and fast data transfers. The router's built-in antenna ensures a wide coverage area, enabling users to enjoy seamless internet access throughout their homes or small offices.

The WRTP54G also integrates a four-port Ethernet switch, allowing users to connect multiple wired devices directly. This feature is particularly useful for setups that require stable connections, such as desktop computers, printers, and game consoles. Each port supports auto-sensing, which optimizes the performance of connected devices.

A standout characteristic of the WRTP54G is its VoIP functionality, enabling users to make phone calls over the internet. With two telephone ports, users can connect regular telephones to the router, facilitating VoIP calls without requiring additional equipment. This feature is complemented by comprehensive call management features, including call waiting, caller ID, and three-way calling, making it a great choice for users looking to reduce traditional phone bills.

Security is a top priority for the WRTP54G, which includes essential security protocols such as WEP, WPA, and WPA2 encryption. These measures help protect users’ data from unauthorized access and ensure a safe browsing experience. Additionally, the router supports firewall features that provide an extra layer of protection against external threats.

In terms of setup and management, Cisco has ensured that the WRTP54G is user-friendly. The web-based interface allows users to easily configure the router, manage network settings, and monitor connected devices.

Overall, the Cisco WRTP54G is a powerful networking solution that combines wireless connectivity with VoIP capabilities, making it an ideal choice for users seeking to enhance their home or small office internet experience. With its combination of flexibility, security, and ease of use, it remains a relevant option in the competitive landscape of home networking technology.
Top Page Image Contents