Cisco Systems 2 manual When you issue the command show version, your router returns

Page 100

640 - 607

B.Network IP-Address

C.IP address IP-address subnet mask.

D.The exit command from the enable configuration

E.Copy running-configuration to startup-configuration

Answer: C

Explanation: The ip address command is used to start IP processing on a router (in fact the same command is also used to do the same on a switch.

Incorrect Answers:

A is incorrect; this is not a valid command.

B is incorrect; the network command is most often used to identify directly connected networks. D is incorrect; this is not a valid command.

E is incorrect; this command will copy the running config to the NVRAM.

Steve McQuerry. Interconnecting Cisco Network Devices. (Cisco Press: 2000) pages 245, 133, 277.

Q. 162

When you issue the command show version, your router returns:

“Configuration register is 0x0101”

From where does the router boot?

A.ROM

B.NVRAM

C.FLASH

D.A TFTP server

Answer: A

Explanation: If you want your router to boot automatically from ROM you need to set the boot field to 1 (0x1).

Incorrect Answers:

B is incorrect; to boot from the NVRAM the boot field must be set from the range of 2 to F (0x2 to 0xF). C is incorrect; to boot from FLASH the boot system flash command would need to be used.

D is incorrect; to boot from a TFTP server the boot system tftp command would need to be used.

Steve McQuerry. Interconnecting Cisco Network Devices. (Cisco Press: 2000) pages 127-130.

Q. 163

Leading the way in IT testing and certification tools, www.testking.com

- 100 -

Image 100

Contents Ccna Important Note Please Read Carefully Which command displays the configuration register setting? Answer DIncorrect Answers Answer D ExplanationAnswer C Explanation Answer B ExplanationExhibit Answer a Explanation Answer B During encapsulation in which order is information packaged? Answer CAnswer E Explanation Answer A, B, E Answer F Explanation What is the result of segmenting a network with a bridge? Answer aPhysical layer Data layer Network layer Transport layer Host 1-1 can ping Host Answer A, B and E Answer B, D, FAnswer A, B, D 640 Answer A, D, F Answer B, C, E Answer A, D Cable #1 Cable #2 Cable #3 Cable #4 Answer A, B 640 Answer D What is the likely cause of this problem? Answer A, C, D Answer Answer B, F 640 RIP Ospf Eigrp Igrp Answer Explanation Answer A, B, D, E Answer D Is incorrect this is not a valid command Answer B Answer D Answer A, C, D, E Which of the following are true? Answer EWhat is a benefit of a virtual LAN VLAN? Answer C, D Answer B Given the configuration example Answer D, E Explanation Answer A, E, F Answer D, F Which two statements about IP RIP are true? Choose twoHow does inter-VLAN communication take place? Answer A, B, C, and D CSMA/CD Answer A, D Which two statements about a bridge are true. Choose two Which statement about an IP network is true? 10.0.0.0 to 172.16.0.0 to 192.168.0.0 to Answer A, B, C, GExplanation Which statement is true? Answer A, B, D Explanation Incorrect OptionsAnswer A, C, E Answer a and B Which two protocol tools use ICMP? Choose twoWhich command successfully ping an individual IP address? Answer A, COne Two None Several Which commands should you use to enable Igrp routing? Answer E Answer A, B, C Explanation Answer B, D Answer A, B, CWhat is the bandwidth capacity of an Isdn B channel? Answer a Which statement about Ethernet networks is true? What is the distance limitation for 100BaseT? Which command sets the clock rate to 56 Kbps on serial0? Setup dialogue what do the square bracket indicate? Which command retrieves the configuration file from NVRAM? What is the most common Layer 2 device? SAP Hdlc ARP Novellether Answer a Answer D Answer A, C What are two components of an IPX address? Answer B, C Explanation Answer C, D, E, F Answer F Which two statements are true? Choose two Answer a and dWhat is a backoff on an 802.3 network? What is a key use of a device hardware address? 16,382 65,534 Session Network Transport Maintenance 640 Answer A, C Explanation What are the characteristics of UDP? MAC LLC SAP LCP Tab Ctrl R Spacebar Right Arrow PPP Lapd Isdn Hdlc Which two commands show your access lists? Choose two What does the command show access-list 101 list?Answer B, C IP and IPX IP and PPP PPP and Sdlc PPP and Hdlc 640 Answer C, D, E Explanation What are two functions of Icmp protocol? Choose TwoAnswer D, E 172.37.2.55 to What does the term ‘Base’ refer to in 100BaseT? Click the task button & Place the encapsulation Answer Explanation IP-Space enable When you issue the command show version, your router returns From where does the router boot?101 What is the most common mail to device? 103 104 105 106 Which statement about Ethernet switches is true? 108 109 110 111 Answer A, B, F 113 You just entered the following command Which operation is most likely to follow?115 Answer A, B, C, D What is back off on an 802.3 network? 118 Which command displays access list 111? Answer B, E120 121 122 123 124 125 126 Answer E, F, G 128 Answer A, D Explanation 130 What is an advantage of local area network LAN segmentation? What are the generic parts of a network layer address?132 133 134 135 136 How does a bridge function? 138 What are two purposes for using switches? Choose two What is an example of a valid MAC address? 141 Which two physical interfaces does PPP support? Choose two Answers C, D143 144 145 146 147 148 149 What is the purpose of ISL and 802.lq frame tagging? 151 152 Which of the following describes isdn bri servie? 154 Answer B What do you use for loop avoidance? Choose two 156 Answer B Diagram 158 Answer A, B, E Identify the effect of Ctrl-Z? 160 161 162 163 Answer a How do you change the Console password to cisco? 165 166 167 Answer D Q299 Answer C 301Answer C 303 Answer D 302Answer a 304 Answer B, C 307 Answer D 309 What is the purpose of DLCIs in Frame Relay? Answer B 310172 173 Answer C 318 175 176 177 178 179 180 Q327 Answer Unknown 328 Answer Unknown

Related manuals

Manual 40 pages 55.56 Kb

Manual 100 pages 60.16 Kb