Dynex DX-WGUSB manual Connecting to a network, Encryption-Use the default encryption

Page 5

DX-WGUSB.fm Page 5 Monday, August 21, 2006 3:20 PM

Configuring the wireless network

5

Connecting to a network

To connect to a network:

1Click Connect on the Available Networks tab. The following screen opens.

5Click Next. The following screen opens.

2Set the values of the following fields:

Network Name—Type a name for the new profile.

Network Type —Select from the list of supported network types. Supported types include:

Peer to Peer—This is the 802.11g peer-to-peer mode (also known as Ad Hoc). Only one wireless cell is supported for each different SSID. All communication is done from client to client without the use of an access point. 802.11g Ad Hoc networking uses the same SSID for establishing the wireless connection.

Access Point—This mode requires an 802.11g or 802.11b access point. All communication is done through the access point, which relays packets of information to other wireless computers as well as to computers on a wired network (such as Ethernet).

Transfer Rate—The transmission rate at which the access point transmits the data packets. You may set this to:

fixed 1 Mbps, fixed 2 Mbps, fixed 5.5 Mbps, fixed 11 Mbps, or Automatic if you are using an 802.11b access point.

fixed 6 Mbps, fixed 9 Mbps, fixed 12 Mbps, fixed 18 Mbps,

fixed 24 Mbps, fixed 36 Mbps, fixed 48 Mbps, fixed 54 Mbps, or Automatic if you are using an 802.11g access point.

3Click Next. The following screen opens.

4Set the values of the following fields:

Authentication Mode—Use the default authentication mode.

Encryption—Use the default encryption.

When encrypted information is received it is only accepted if it decrypts correctly. This happens only if the computer has the WEP Key used by the access point. This screen lets you enter the WEP key.

6Set the values of the following fields:

Input Method—Select the input method that matches the input method used by the access point.

Key—Enter the WEP Key. This key must be the same as the key used by the access point. It must be between 8 and 63 characters long.

Note: Use only the digits 0-9 and letters A-F for the key.

Key Index—Select the key index that matches the key index

used by the access point.

7Click Next. The following screen opens.

8If you want to set the IP setting, click Enable, then go to step 9. -OR-

If you want the IP setting to be set up automatically, click Disable, then click Complete. You are finished.

Image 5
Contents DX-WGUSB Introduction ContentsInstalling the software and hardware Installing the software and hardware Uninstalling the software and hardwareTo uninstall the software and hardware Remove the USB adapter Restart your computerAvailable Networks tab Configuring the wireless networkLink Information tab To connect to a network Connecting to a networkEncryption-Use the default encryption Profile Setting tab TroubleshootingTroubleshooting About tabFederal Communication Commission Interference Statement Legal noticesIC statement for DX-WGUSB Important NoteTable des matières Installation du logiciel et du matérielTable des matières Installation du logiciel et du matériel Configuration du réseau sans fil Configuration du réseau sans filOnglet Link Information Information de liaison Retirer ladaptateur USB Redémarrer lordinateurConnexion à un réseau Onglet Available Networks Réseaux disponiblesPour le raccordement à un point d’accès Pour se connecter à un réseauOnglet About À propos de Onglet de paramétrage du profil ProfileCorrespond à celui utilisé par le point d’accès 10 Régler les valeurs des champs suivantsProblèmes et solutions Problèmes et solutionsAvis juridiques Remarque importante pour le modèleIntroducción ContenidoInstalación del software y del hardware ContenidoRepita los pasos 10 al 12 para agregar el protocolo IPX/SPX Instalación del software y del hardwareConfiguración de la red inalámbrica Configuración de la red inalámbricaDesinstalar el software y el hardware La ficha Link Information Información del EnlaceConexión a una red Ficha Available Networks Redes DisponiblesPara conectarse a un punto de acceso Para conectarse a una redHaga clic en Complete Completar. Ha terminado Ficha de Ajustes de PerfilFicha About Acerca de Avisos legales Localización y corrección de fallasLocalización y corrección de fallas Declaración del IC para DX-WGUSBPenn Ave. South, Richfield, MN 55423 U.S.A