Extron electronic DVS 605 setup guide Powering Up, Front Panel Overview

Page 2

DVS 605 • Setup Guide (Continued)

Powering Up

When the DVS 605 powers up, it performs a self testing sequence (see image below). The LCD displays the default display cycle, with the signal type, resolution, and refresh rate for the currently selected input and the output resolution and refresh rate.

NOTE: When powered and not in any menu, the LCD screen defaults to cycling through the current input/output status. The displayed content

may vary depending on the input video signal type (see typical default display below).

Apply

Power

 

Display screen

13 sec.

starts blank.

 

 

 

 

 

EXTRON

 

 

 

16 sec.

 

 

ELECTRONICS

 

 

 

 

 

 

 

All input LEDs flash

 

 

(red then green).

 

1

2

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note: Times shown are approximate.

 

 

Default Display Cycle

 

 

 

 

 

 

 

 

 

IN

RGBHV

2

IN

31.47 kHz

EXTRON

11 sec.

60-1059-xx

2 sec.

sec.

#1

640x480

 

#1

59.94 Hz

DVS 605 XX

 

FW v1.xx

 

 

 

 

 

 

 

 

 

 

 

 

 

2 sec.

OUTPUT

 

2 sec.

Last active input

 

 

 

 

 

720p@60

 

 

button(s) remains lit.

1

45PIP

Front Panel Overview

The DVS 605 is shown here. All other models have the same features shown below.

 

 

 

 

 

 

3

 

 

1

2

3

 

AUTO

 

 

 

 

 

 

 

 

 

 

 

EXTRON

4

5

 

PIP

 

SWAP

 

 

 

DVS 605

CONFIG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVS 605

MENU

DIGITAL VIDEO SCALER

 

 

ADJUST

 

 

 

NEXT

 

 

 

 

1

2

4

5

6

7

A Front panel mini USB configuration port — Connect a control system or computer to this mini USB port (cable not supplied), for device configuration, control, and upgrading the firmware.

B Input selection buttons and LEDs (1-5) — Selects and switches inputs; adjacent LEDs indicate which input is active (current input lights green, PIP (Picture-In-Picture) input lights red).

C Auto-Image(Auto) button — When pressed, this initiates automatic image size and centering adjustments on the selected input.

D PIP and Swap Image buttons — These two buttons are:

PIP — Opens or closes the PIP window

Swap — Swaps the main displayed image and the current PIP input with each other, or when not in PIP mode, it switches between current and previous input.

E LCD display — This 12x2 screen displays device settings and menu configuration information.

F Menu navigation buttons (Menu, Next) — These buttons allow navigation through the menu system of the DVS 605. G Adjust knobs — These are used with the menu navigation buttons to adjust the device settings and picture control.

Setting the Front Panel Locks (Executive Modes)

The DVS 605 has three modes of front panel security lock that limit the operation of the unit from the front panel.

Executive mode 0 (disabled) — The front panel is fully unlocked. This is the default setting.

Executive mode 1 (enabled) — The front panel is completely locked. Can only be enabled and disabled using SIS commands, or through the embedded web pages. See the online DVS 605 User Guide or rear page of this guide for SIS commands.

Executive mode 2 (enabled) — The front panel is locked except for input switching, PIP, swap, and Auto-Image.

Enabling or disabling Executive mode 2 from the front panel

If the DVS 605 unit is in Executive mode 0 (unlocked), the procedure shown at right selects mode 2 (locked). If it is in Executive mode 2, this procedure selects mode 0 (unlocked).

When Executive mode 2 is enabled and a front panel action is attempted (other than input switching, PIP enable or disable, swap, and Auto-Image), the LCD displays the lock status for 2 seconds.

Press and hold for about

2 seconds.

MENU

NEXT

LCD screen displays

either

EXEC. MODE 2

ENABLED

or

EXEC. MODE

DISABLED

2

Image 2
Contents Mounting and Cabling InstallationRear Panel Features Enabling or disabling Executive mode 2 from the front panel Powering UpSetting the Front Panel Locks Executive Modes Front Panel OverviewInternal Web pages Configuring the DVSFront Panel Menu System Connected Hdmi displayIdhX1 Upgrading the Firmware Using the Web PagesX2@ EX1 CI IpiX1
Related manuals
Manual 98 pages 46.7 Kb