Configuring the DVS, Internal Web pages | Extron electronic DVS 605

Configuring the DVS 605

DVS 605 devices can be configured by any of the following: via the front panel, via the internal web pages, or via RS-232/Ethernet or USB connection, using the SIS commands (see the rear page).

Front Panel Menu System

The scaler has seven front panel configuration menus: • User Presets • Picture Control • Input Configuration • Output Configuration

•Audio Configuration • Advanced Configuration • View Comm Settings • Exit Menu. A hidden menu (Edit Comm Settings) is also accessible (see note after the following figure).

Default Display Cycle

USER

PICTURE

INPUT

OUTPUT

PRESETS

CONTROL

CONFIG

RGBHV

sec.

31.47 kHz

59.94 Hz

640x480

2 sec.

OUTPUT

2 sec.

AUDIO

ADVANCED

VIEW COMM

EXIT MENU?

720p@60

CONFIG

SETTINGS

PRESS NEXT

Menu	Menu
Next

NOTE: To access the hidden Edit Comm Settings menu, press and hold the Input 5 and the Next button simultaneously. Release buttons when

the menu appears. Edit the setting as needed, then press Menu to exit and save the settings.

To use any menu, press the Menu button to access the main menu, then repeatedly press the Menu button to cycle through to the desired menu. Press the Next button to enter and cycle through the desired submenu.

NOTE: Press Menu at any time to exit a submenu and return to the main menu.

For detailed information on the menus, see the DVS 605 User Guide, available online at www.extron.com.

To configure the DVS 605 using the front panel, follow the steps below:

1.	Within the Output Configuration menu, use the Adjust knobs to select the output resolution and refresh rate, the output signal
	type, and the sync polarity to match the requirements of the analog display device. The HDMI format can be set to match the
	connected HDMI display.
2.	From the Advanced Configuration menu, Test Pattern submenu, select the Alternating Pixels (Alt. Pixels) test pattern. Adjust the
	connected analog display active pixels (size), total pixels (clocking), and pixel phase (fine sync) settings for optimal picture quality.
3.	From the Advanced Configuration menu, change the test pattern to Crop, and adjust the image position settings until all four sides
	of the crop pattern are visible. Disable the test pattern. No further adjustments or Auto-Image functions should be performed on the
	display device itself.
4.	Use the Advanced Configuration menu to set the Aspect Ratio (Fill or Follow) for each input. Rotate either Adjust knob to the desired
	setting.
5.	Perform an Auto-Image on each DVS 605 input. Auto-Image is a quick way to size an input to fit the current window size.
	To perform Auto-Image on the current input, press the Auto-Image button, then press it again to confirm.
NOTE: Alternatively using the Input Configuration menu, make any desired advanced adjustments, including turning on or off Film detection,
	Horizontal and Vertical Start, Active Lines, Pixel Phase, and EDID setting selection.
6.	Adjust the Overscan mode under the Advanced Configuration menu as required. Overscan masks Closed Caption and ancillary data
	common on broadcast signals. (Applies to SMPTE input resolutions only.)
7.	Use the Picture Control buttons to adjust the Horizontal and Vertical Position and Size, Brightness and Contrast, Color and Tint, and
	Detail settings if needed.
8.	Use the User Presets menu to save the adjustments to each input for manual recall later.

Internal Web pages

The DVS 605 can be configured, controlled, and operated through the Ethernet port when connected to a LAN or WAN, using a web browser such as Microsoft® Internet Explorer®. The browser displays the factory-installed web pages, which provide a means of viewing and operating the device. Access the HTML pages by entering the IP address of the unit in the browser Address field.

NOTE: If the system administrator has not changed it, the factory default IP address is 192.168.254.254. DHCP is disabled. If the unit is

password-protected, enter the administrator or user password in the Password field.

A user name entry is required. Enter admin for administrator level or user for user level (all lower case letters).