Extron electronic ISS 108, ISS 408 Auto Imaging and Auto Memories submenu, Enhanced Mode submenu

Page 36

Operation, cont’d

Auto Imaging and Auto Memories submenu

The Auto Imaging and Auto Memories menu provides a means to turn the auto imaging and auto presets features on or off for all input selections.

If auto imaging is set to on, the ISS automatically sizes and centers the selected input to fill the screen when a new frequency is input. If auto imaging is set off, the ISS sizes and centers the selected input only when it is commanded using the input button, see Auto imaging an input, earlier in this chapter. Rotate the Adjust knob to toggle auto imaging on or off for all input selections.

The auto memories feature saves and recalls centering, sizing, and filtering information, based on the input frequency. Auto memory settings may conflict with user preset settings. When you use a control system to switch inputs and then recall a user memory, the delay in recalling the auto memory settings could result in the recalled auto memory settings overwriting the recalled user memory settings. To prevent this conflict, turn auto memories off. Rotate the Adjust knob to toggle auto memories on or off

Enhanced Mode submenu

The Enhanced Mode submenu provides a means to turn enhanced mode on or off. Enhanced mode is an automatic gain control for S-video or composite video input signals scaled and applied to the program output. If the input signal level is too weak, the signal gain is increased; if the input signal level is strong, the signal gain is decreased.

Use either the Adjust or the Adjust knob to select among enhanced mode off or on for the program output. The default is Off.

Enhanced mode is only effective for S-video and composite video input signals.

Pixel Phase submenu

The Pixel Phase submenu displays and lets you set the pixel phase, which is the timing of the digital scaler’s sampling. Sampling at the optimum pixel phase results in a brighter scaled output.

Use either the Adjust or the Adjust knob to select the pixel phase for both outputs simultaneously from 0 to 31. The default is 16.

Preview Switch Mode submenu

The Preview Switch Mode submenu lets you set the way the preview output responds to the cut or dissolve operation.

•Stay mode — When you initiate either a cut or dissolve operation, the video and audio signals on the preview output are applied to the program output (figure 3-14) and also continue to be applied to the preview output until another input is selected.

The video input switches between the switcher’s two internal scalers, resulting in a switching report being issued on the RS-232 port (see Switcher-Initiated Messages in chapter 4, Operation).

•Swap mode — When you initiate either a cut or dissolve operation, the preview and program outputs are swapped (figure 3-14). The video and audio signals on the preview output are applied to the program output. The video and audio signals that had been applied to the program output are applied to the preview output.

Each of the switcher’s two internal scalers retains the same video inputs; only the outputs are swapped. No switching report is issued on the RS-232 port (see Switcher-Initiated Messages in chapter 4, Operation).

3-14 Integration Seamless Switcher • Operation

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Integration Seamless Switchers ISS 408 & ISSSafety Instructions English Consignes de Sécurité FrançaisSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolQuick Start Integration Seamless Switcher QS-1Quick Start Integration Seamless Switcher, cont’d QS-2Table of Contents Table of Contents, cont’d Integration Seamless Switcher Table of Contents Iii Iv Integration Seamless Switcher Table of Contents One About the Switcher Integration Seamless Switcher IntroductionIntroductiontroduction, cont’d About this ManualTypical ISS 408 Integration Seamless Switcher application Features Introduction, cont’dIntegration Seamless Switcher Introduction Introduction, cont’d Two Installationstallation, cont’d Mounting the SwitcherTabletop placement Integration Seamless Switcher InstallationCabling and Rear Panel Views Input connectionsInstallation, cont’d Captive screw connector wiring for inputsStandard output connections BNC output connections for Rgbhv and Rgbs videoCabling and RJ-45 connector wiring Optional output connectionEthernet connection Choosing a network cableWiring the network cable RJ-45 connector pinout tableConfiguration RS-232 connectionThree Front Panel Controls and Indicators Integration Seamless Switcher OperationOperationeration, cont’d Black/Mute, input selection, and Cut/Dissolve controlsPicture adjustment and menu system controls InputsPower-on indications Operation, cont’dFront Panel Operations Selecting an input and switching it to the program output Default Display CycleCutting to the selected input Recalling a user preset Auto imaging an inputMenu system overview Extron Electronics ISS 60-423-01 VersionVideo & Audio Configuration menu Input Configuration submenuOutput Configuration menu Output Resolution submenuResolution 50 Hz 56 Hz 60 Hz 75 Hz 85 Hz Lock at 50/60 Hz Sync Type and Polarity submenuAdvanced Configuration menu Video & AudioBlue Only Mode and Edge Smoothing submenu RGB Delay submenuDissolve Speed submenu Test Pattern submenuEnhanced Mode submenu Pixel Phase submenuPreview Switch Mode submenu Auto Imaging and Auto Memories submenuPAL Film Mode submenu Reset submenuUser Presets menu Save Preview Preset submenuErase Preview Presets submenu Exit menuPicture adjustments 127 128 063 450 400 500 550Front panel security lockout executive mode Adjust knobs have no mechanical limits to their rotationOptimizing the Video IP informationSetting up a DVD source Controls to position the imageTroubleshooting Optimizing the AudioGeneral checks Specific problems Problem Cause SolutionOperation, cont’d Four Integration Seamless Switcher Programmer’s Guide RS-232 LinkEthernet Link Symbols Default addressSwitcher-Initiated Messages Power-upProgrammer’s Guide, cont’d Input selectionCutting or dissolving in swap mode Input and output video typeRGB delay and dissolve speed Preview switch mode PAL film modeTest pattern Audio gain and attenuationHost-to-Switcher Instructions Switcher Error ResponsesUsing the Command/ Response Table Automated adjustmentsCommand/response table for SIS commands Command Ascii Command Response Additional descriptionScaler output video type ColorTint BrightnessPixel phase Horizontal shiftVertical shift Top blankingUser presets Vertical detail filter RGB and component video inputsDetail filter S-video and composite video inputs Auto MemoriesExecutive mode Verbose modeSet audio gain and attenuation Audio muteResets Information requestsCommand/response table for IP SIS commands Date and time entered should be Greenwich Mean Time GMTCommand/response table for special function SIS commands Command Ascii Command ResponsePAL film mode Preview switch modeAuto Image Command Hex Command Response Memory backupFive Installing the software Ethernet protocol settingsIntegration Seamless Switcher Switcher Software Control Software for WindowsUsing the control program If you selected a comm port, proceed to stepSwitcher Software, cont’d Windows Control program windowUsing the help program Installing the softwareUsing the software Button Label GeneratorExtron’s Button-Label Generator window Six Integration Seamless Switcher Ethernet Operation EthernetOperation,cont’dLoad the Startup Control Control ControlSelect and switch an input Change the RGB delay or dissolve speedEthernet Operation, cont’d Blackout the screen and mute the audio Freeze the outputOutput a test pattern Preview the scan rateSystem Configuration Administration fieldsISS IP Settings fields ISS IP Address fieldISS Name field Hardware Address fieldFile Management File ManagementInput configuration SetupOutput resolution, rate, sync format, and polarity Output resolution Output rateOutput format Output polaritySeven Opening and Closing the Switcher Integration Seamless Switcher Maintenance and ModificationsFirmware Upgrade Installation DVI Output Card Installation DVI output card connector opening and socket J14Output DVI board installation Maintenance and Modifications AAppendix a Integration Seamless Switcher Ethernet Connection Ethernet Connection, cont’dPing to determine the switcher’s IP address Ping to determine Web IP addressConnect as a Telnet client Telnet tipsOpen Escape character and Esc key Local echoSet carriage return-line feed CloseEthernet Connection, cont’d AppendixBB Specifications Integration Seamless Switcher Reference InformationAudio Optional accessoriess Reference Information, cont’dPart Numbers Included partsButton Labels Reference Information, cont’d Integration Seamless Switcher Reference Information Reference Information, cont’d FCC Class B Notice Extron Electronics, USA
Related manuals
Manual 109 pages 40.47 Kb Manual 2 pages 44.27 Kb

ISS 408, ISS 108 specifications

Extron Electronics is renowned for its contributions to the audiovisual industry, providing high-performance devices that meet the demands of professional environments. Two prominent products in their lineup are the ISS 108 and ISS 408 image scaling switchers, which are designed to enhance the management and quality of video signals in various applications.

The Extron ISS 108 is an 8x1 image scaling switcher that allows users to seamlessly switch between multiple video sources while ensuring high image quality. One of its main features is the ability to support a variety of video formats, including resolutions up to 4K. This versatility is crucial for applications in education, corporate settings, and events where different video sources may be required.

In terms of technology, the ISS 108 is equipped with advanced image scaling capabilities that improve the visual quality of the content being displayed. The device utilizes Extron's patented Vector 4K scaling technology, which enhances the clarity and detail of the images while maintaining the integrity of the source material. This technology is invaluable in environments where every detail matters, and it ensures that presentations are delivered at their best quality.

The ISS 408, on the other hand, takes the capabilities of the ISS 108 and elevates them further by offering 4x1 switching capabilities. This enables users to connect up to four video sources, giving them more flexibility in content management. The ISS 408 also supports 4K video resolutions, further solidifying Extron's commitment to delivering high-quality solutions.

Both models are designed with user-friendly interfaces, allowing for easy operation and integration into existing AV systems. They offer extensive control options, including RS-232 and Ethernet, enabling users to incorporate them into automation systems and control environments efficiently.

Another important characteristic of the ISS series is their built-in security features, such as password protection and lockout modes, which are essential for maintaining the integrity of sensitive content being delivered in corporate or educational settings.

In summary, the Extron ISS 108 and ISS 408 provide powerful solutions for image scaling and video switching. With advanced technologies like Vector 4K scaling, robust connectivity options, and intuitive control interfaces, these devices stand out as essential tools for any professional audiovisual application. Their focus on quality, flexibility, and security makes them ideal choices for enhancing video presentations in various environments.
Top Page Image Contents