Extron electronic MLS 608 D setup guide Connect Outputs from MTP/HDMI U R, Connect Control Devices

Page 4

MLS 608 D Series • Setup Guide (Continued)

Step 4 — Connect Outputs from MTP/HDMI U R

Digital video — Connect a display to the HDMI connector for digital video output.

Analog video — Connect the analog outputs as shown at right.

Audio — Connect a suitable audio device, such as powered speakers, to the 5-pole captive screw audio output connector for a balanced or unbalanced, dual mono audio signal. Wire connector as shown at right.

Component Video –

Composite Video –

RS-232 Control (Analog Side) –

 

 

Connect to these 3 BNCs.

Connect to this BNC.

NOT USED IN THE MLS 608 D SYSTEM.

 

 

 

 

 

 

RS-232

 

 

Mono output 1

 

 

 

 

 

 

 

MONO L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NO GROUND.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sleeve(s)

 

 

 

 

 

 

 

 

AUDI R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R-Y

 

 

 

 

 

 

 

Mono output 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Y

B-Y

 

 

Tx Rx

SPARE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VID

 

 

NO GROUND.

 

 

 

 

 

 

 

 

2

 

Unbalanced Output

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

MONO AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mono output 1+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONO L

Do not tin

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGB

Y/C

 

 

 

Mono output 1-

 

 

 

 

 

 

 

 

 

 

 

 

the wires!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANALOG OUTPUTS

 

 

Sleeve(s)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUDI R

 

 

 

 

 

 

 

Mono output 2+

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RGBHV and RGBS –

S-videoConnect to

Mono Audio – Connect

Mono output 2-

 

 

 

 

 

 

 

 

Connect to this VGA

this mini DIN connector.

to this captive screw

 

 

Balanced Output

 

 

connector.

 

 

 

 

 

connector.

Wire the audio connector as shown above.

NOTE: The audio signal is detected on the MTP input and then is distributed to the audio connector for output.

RS-232 control (digital side) — Connect a serial communications port on a display device to the

3.5mm, 3-pole captive screw connector (labeled RS-232 pass-thru) for pass-through RS-232 bidirectional communication. Wire the connector as shown at right.

NOTE: The RS-232 control port on the analog side is not used in the MLS 608 D system.

RS-232 Device Pins

Rx

Tx

Ground

Tx

MTP/HDMI

Rx

RS-232

 

Pass-thru

 

port

Step 5 — Connect Control Devices

RS-232 control — Connect a host computer or control system (such as an optional MLC 226) to the 5-pin connector (see M on page 1) for MLS switcher configuration and control via RS-232 using Extron software or Simple Instruction Set (SIS) commands.

Wire the MLS as shown at right.

RS-232

MLS 608 D SA

Host

 

Tx Rx

MLS 608 D

 

rear panel

 

RS-232 Host

MLS 608 D SA

port

Rear Panel

NOTE: This serial port is independent of the front panel configuration port. Both may be used for MLS control.

RS-232 protocol (default values):

• 38400 baud •1 stop bit • no parity • 8 data bits • no flow control

NOTE: The ‘+’ and ‘-’ pins on this connector can be used to

NOTE: You must connect a ground wire between the MLC and MLS.

+12 VDC input

 

Ground (

 

 

)

 

 

 

 

 

 

 

 

 

 

 

 

Ground (

 

 

)

 

 

 

Transmit (Tx) B

 

 

 

 

B Receive (Rx)

 

 

 

 

 

 

A Transmit (Tx)

 

 

Receive (Rx) A

 

Tx/IR Rx GROUND SNSPWR GROUND OUT+12V

A+12VOUT BGROUND MOD IRIND SCPCOME

COMMON

1

2

COMMON

3

4

COMMON

5

6

 

 

CONT

 

 

 

 

 

 

 

 

 

 

 

DISPLAY

 

A B C

D E

 

A

 

 

 

B

 

 

C

 

 

 

 

 

 

RELAYS

 

 

 

RS-232/IR

 

CM/IR/SCP

 

 

NORMALLY OPEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MLC 226 IP

Bottom Panel

/xTIR GROUND

/xTIR GROUND

/xTIR GROUND

Rx

Tx

GROUND GROUND +12VIN

 

 

 

A B

 

A

B

C

MLS

PWR

 

IR/SERIAL OUT

 

 

 

 

RS-232 12V

power a controller, for example an MLC 226 IP and a connected IRCM-DV+.

NOTE: If you use cable that has

 

 

 

MLC's

a drain wire, tie the drain wire

 

 

 

 

 

 

MLS and

to ground at both ends.

 

 

 

Rx Tx

GROUND GROUND +12VIN

Power

 

A B

ports

 

MLS

PWR

 

 

RS-232 12V

 

RS-232 Insert port (optional) — Connect an optional control

device (for example an MLC 226 IP via the RS-232 display control port) to the 5-pin connector (see N on page 1) for pass through RS-232 communication to a connected projector or display device.

Wire the connection as shown at right.

Transmit (Tx)

Receive (Rx)

Ground ( )

Tx/IR

Rx

GROUND PWR SNS GROUND

+12V OUT

 

DISPLAY

 

 

 

RS-232/IR

 

MLC 226 Display port

RS-232 INSERT

Tx Rx

N/A

N/A

MLS 608 D rear panel RS-232 Insert port

Step 6 — Connect Power

MLS 608 D — Plug in a standard IEC power cord from a 110 - 240 VAC, 50 - 60 Hz power source into the receptacle (see A on page 1).

Optional — Connect the 2-pole power connector (see E on page 1) for remote power to an MTP transmitter or receiver. Wire the connection as shown at right.

Optional — Connect the “+” and ”-” pins on the RS-232 connector (see M on page 1) for remote power to an optional controller (such as the MLC 226). See second note, step 4 above.

MTP/HDMI U R — Connect the 2-pole 3.5 millimeter captive screw connector from the 12 VDC,

1.0A external power supply (provided) to this receptacle on the rear panel, or connect to the 2-pole power connector (see E on page 1) on the MLS 608 D. Wire connector as shown at right.

For both devices, when power is applied the front panel power LED lights.

Smooth Ridges

A

A

Power Supply

Output Cord

SECTION A–A

2-pole Captive

Screw

Connector

Tie Wrap

3

4

Image 4
Contents Rear Panel Features MLS 608 D and MTP Hdmi U R MLS 608 D SATwisted Pair TP Cable Transmission Distance Analog signalsTo receiver Installation and Cabling Mount the SwitcherConnect MLS 608 D Inputs Connect MLS 608 D OutputsConnect Power Connect Outputs from MTP/HDMI U RConnect Control Devices RS-232 Insert port optional Connect an optional controlSetting the Peaking and Level on the MTP/HDMI U R Setting the Skew on the MLS 608 DOptimizing Video Selecting the MLS 608 D Output PrepeakingAll models have the following front panel features Front Panel FeaturesFront Panel Operation Using the DSP Configurator Software Basic Simple Instruction Set SIS CommandsInputs Connector and Cable InformationTwisted Pair RJ-45 Cabling

MLS 608 D SA, MLS 608 D, MLS 608 D MA specifications

Extron Electronics has long been a leader in the field of AV technology, and their MLS 608 D and MLS 608 D MA, MLS 608 D SA models are perfect examples of their commitment to delivering high-quality solutions for a range of applications. Designed primarily for educational and corporate environments, these systems are built to provide superior performance, advanced features, and ease of use.

The MLS 608 D is a versatile AV control system that incorporates various audio and video technologies to facilitate seamless integration within any AV setup. One of its standout features is its ability to manage multiple sources and destinations, allowing users to switch between different input signals with ease. This makes it an ideal choice for classrooms, conference rooms, and auditoriums where multiple devices might need to be connected efficiently.

A key characteristic of the MLS 608 D is its ability to support high-definition video formats. By supporting resolutions up to 4K, it ensures that presentations, videos, and other visual content are displayed with stunning clarity and detail. Additionally, it integrates seamlessly with modern display technology and can connect to a wide range of devices, further enhancing its versatility.

The MLS 608 D MA and MLS 608 D SA models cater to specific needs within audio management. The MA version offers advanced audio mixing capabilities, enabling users to adjust sound levels from various inputs. This is particularly useful in environments where audio balance is crucial, such as large lecture halls or meeting spaces. The SA version specializes in audio amplification, providing powerful output to ensure clear and consistent sound delivery throughout larger areas.

Both the MLS 608 D MA and SA incorporate user-friendly interfaces, often featuring customizable control options that enhance usability. With built-in diagnostics, these systems monitor performance and simplify troubleshooting, which is vital for maintaining operational efficiency in busy environments.

Furthermore, the integration of Extron's renowned AV technologies, such as control processing and scaling, enhances the overall functionality of these systems. They also allow for flexible control options, utilizing RS232, Ethernet, and various other protocols, ensuring compatibility with existing AV infrastructure.

In summary, Extron's MLS 608 D, MLS 608 D MA, and MLS 608 D SA models exemplify excellence in AV control and management. With their advanced features, superior audio and video capabilities, and user-centered design, they are poised to elevate any audiovisual experience in a variety of settings.