Extron electronic MLS 103 V, MLS 102 VGA Installation, cont’d, Rear Panel Features and Cabling

Page 8

Installation, cont’d

Furniture or projector mounting

Furniture mount or projector mount the MLS using the optional mounting kit (part #70-212-01, furniture; or 70-217-01, projector) as follows:

Rear Panel Features and Cabling

Turn off and disconnect power from all the equipment before you connect cables to the MLS.

1.

Attach the mounting brackets to the MLS with the

 

machine screws provided.

2.

If feet were previously installed on the bottom of the MLS,

 

remove them.

For furniture mounting

3a. Hold the MLS with the attached brackets against the underside of the table or other furniture. Mark the location of the screw holes of the bracket on the mounting surface.

4a. Drill 3/32” (2 mm) diameter pilot holes, 1/4” (6.3 mm) deep in the mounting surface at the marked screw locations.

5a. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until just less than 1/4” of the screw protrudes.

6a. Align the mounting screws with the slots in the brackets

and place the MLS against the surface, with

the screws through the bracket slots. See the illustration at left.

 

1

 

2

MLS 102 VGA

 

 

 

1

2

 

 

INPUTS

 

OUTPUT

AUDIO INPUTS

AUX/MIX

OUT

MLC/RS-232

1 2 L 3 R

L 4 R MONO

L R

POWER

 

 

 

 

A B

MLS 102 VGA

 

 

12V

.5A MAX

7

8

9

10

11

5 6

MLS 103 V

1

2

3

 

 

 

 

INPUTS

 

 

OUTPUT

 

 

AUDIO INPUTS

AUX/MIX

 

OUT

MLC/RS-232

L 1 R L

2 R L 3 R L

4 R MONO

L

R

POWER

A B

MLS 103 V

12V

.5A MAX

8 9 10 11

 

 

 

3

 

 

 

 

4

 

MLS 103 SV

 

 

 

 

 

 

 

 

1

2

 

 

3

 

 

 

 

 

 

 

INPUTS

 

 

 

 

OUTPUT

 

 

 

AUDIO INPUTS

 

 

AUX/MIX

 

OUT

MLC/RS-232

L 1

R

L 2 R L 3

R L

4

R

MONO

L

R

POWER

A B

MLS 103 SV

 

12V

.5A MAX

8

9

10

11

MLS 100 A

AUDIO INPUTS

AUX/MIX

OUT

 

MLC/RS-232

L 1 R L 2 R L 3 R L 4 R

MONO

L

R

POWER

A B

MLS 100 A

 

12V

.5A MAX

8

9

10

11

Mounting the MLS to furniture

 

Projector

 

 

 

Mounting

7a.

Slide the switcher slightly forward or

Bracket

 

 

back, then tighten all four screws to

Mounting

 

secure the MLS in place.

 

Bolt

 

 

 

For projector mounting

 

 

3b.

Secure the MLS to a projector

Ceiling

 

 

mount or other surface by

 

 

 

 

 

inserting the mounting bolt

 

 

 

through the bracket’s slotted

 

 

 

hole, as shown at right.

 

 

 

 

 

Digital Projector

Mounting the MLS to a projector mount

Video connections

1Computer video inputs (MLS 102 VGA only) — Cable one or two VGA-UXGA computers to these individually buffered

15-pin HD connectors. These inputs provide ID bit termination.

2Computer video output (MLS 102 VGA only) — Connect a cable from this 15-pin HD connector to the input port of the projector or display.

3S-video inputs (MLS 103 SV only) — Cable up to three S-video sources to the MLS via these female 4-pin mini DIN connectors.

4S-video output (MLS 103 SV only) — Connect the S-video input port of the projector or display to the MLS by plugging S- video cables into these female 4-pin mini DIN connectors.

5Composite video inputs (MLS 103 V only) — Connect up to three composite video input sources to the MLS 103 V using coaxial cables and these female BNCs.

6Composite video output (MLS 103 V only) — Attach a coaxial cable to this female BNC, and connect the other end of the cable to the projector’s or display’s video input port.

2-4

MediaLink VersaTools Switchers • Installation

MediaLink VersaTools Switchers • Installation

2-5

Image 8
Contents MediaLink VersaTools Switchers User’s ManualFCC Class a Notice PrecautionsExtron’s Warranty Quick Start Guide MLS 100 Series Attach the cables. See the instructions beginning onTable of Contents MediaLink VersaTools Switchers Table of Contents, cont’dOne IntroductionIntroduction InstallationTwo Installation UL/Safety RequirementsMounting the Switchers Tabletop useInstallation, cont’d Rear Panel Features and CablingFurniture or projector mounting Video connectionsAudio connections Aux/Mix Mono audio input all models -The Aux/MixTypical Audio Levels for Various Equipment Types Setting Up Optimal Audio GainControl and power connections Gain and Attenuation Settings for MLS 100 Series Switchers Application DiagramsSetup via the MediaLink Control Software Chapter Three OperationFront Panel Features and Operation Executive mode enabling and disabling front panel buttonsMediaLink VersaTools Switchers Operation OperationOperation, cont’d Troubleshooting Operation, cont’d 4ChapterSerial Communication MLC/RS-232 Power port pin assignments Serial CommunicationRS-232 Programmer’s Guide Host-to-MLS communicationsCommand/response table for SIS commands Serial Communication, cont’dCommand/response table for special function SIS commands Installing the softwareUsing the control program Control Software for WindowsUser Mode For stand-alone MLS 100 Series switchersSpecial features For MLS 100 Series switchers controlled by an MLCSwitcher MLS Config Saving and restoring configurationsEmulation mode Specifications, Part Numbers Accessories Using the help programAAppendix a Key to file namesSpecifications, Part Numbers, and Accessories Specifications, Part Numbers, Accessories, cont’d Control/remote switcherAudio output GeneralAccessories CablesAdapters Plenum Comm-link cable Part number
Related manuals
Manual 27 pages 43.28 Kb

MLS 100 A, MLS 103 SV, MLS 102 VGA, MLS 103 V specifications

Extron Electronics is renowned for its innovative and high-quality AV solutions, and the MLS series, including the MLS 102 VGA, MLS 100 A, MLS 103 SV, and MLS 103 V, exemplifies the company's commitment to excellence in audio-visual integration. These MediaLink Switchers are designed to simplify the management of multiple audio and video sources in classrooms and conference rooms, providing seamless integration and user-friendly operation.

The MLS 102 VGA model focuses on VGA signals, making it a reliable choice for installations that primarily use legacy video sources. It features a simple interface with push-button controls, enabling users to easily switch between two video sources with a single VGA output. This model is ideal for educational environments where older laptops and PCs are still in use.

The MLS 100 A model adds audio capabilities to the mix, offering audio switching along with video. This switcher supports stereo audio signals, allowing educators to present multimedia content effectively. The MLS 100 A simplifies the setup for instructors, enabling them to connect different media sources without complicated wiring or extensive technical knowledge.

The MLS 103 SV and MLS 103 V models elevate functionality with their multi-format switching capabilities. The MLS 103 SV supports both VGA video and stereo audio, while the MLS 103 V is solely focused on video. Both models provide a more comprehensive solution for modern AV requirements. The MLS 103 series employs advanced signal processing technology, ensuring high performance across multiple resolutions and formats.

Additionally, the MLS 103 series incorporates features such as EDID management, which automatically configures the video output to ensure compatibility with a variety of display devices. This eliminates the need for users to worry about the technicalities, enabling a smooth, hassle-free experience.

Scalability is another key characteristic of the MLS series. These devices can be seamlessly integrated with other Extron products, allowing for an expandable AV infrastructure that meets the growing demands of technology in educational and corporate environments.

Durable construction, easy installation, and operation make the MLS series a preferred choice among AV professionals. Whether for a small meeting room or a large lecture hall, Extron's MLS 102 VGA, MLS 100 A, MLS 103 SV, and MLS 103 V models deliver flexibility, reliability, and superior performance, enhancing any audio-visual presentation.