Extron electronic RGB 192 Mounting the Interfaces, Tabletop placement, Under-desk mounting

Page 7

Instaltal lationandandOperation,cont’d

Installation Overview

This is an overview of the installation process. You will find detailed installation and operation instructions in this chapter.

Install and set up the RGB 190F, RGB 192 or RGB 198 interfaces by following these basic steps:

1Turn off all of the equipment (computers, remote controls, interface, projector/monitor, local monitor and speakers or other audio device). Disconnect the power cords from the power source.

2Install the rubber feet for tabletop use, or install the appropriate brackets to rack mount the interface. See Mounting the Interfaces below.

3Connect the input (computer video and audio (RGB 192 and 198 only)) and outputs (display, local monitor, and audio (RGB 192 and 198 only)). See Connections and Switches in this chapter.

4Set the front panel DIP switches. See Connections and Switches, in this chapter, as a guide.

5Connect power cords and turn on the devices: output devices (projector, monitors, speakers (RGB 192 and 198 only)), interface, and the source computer.

6Adjust horizontal centering and set the Level DIP switch to obtain the best picture.

Mounting the Interfaces

The interfaces provide several mounting options: tabletop placement, under-desk mounting, through-desk mounting or (for the RGB 198 only) rack mounting. Follow the appropriate procedure on the next three pages.

Tabletop placement

For tabletop or desktop placement only, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the interface enclosure.

Under-desk mounting

1.

Secure the included under-desk mounting brackets

 

(part #70-077-01) to the interface with the machine screws

 

that are already installed in the side of the interface

 

(figure 2-1).

Figure 2-1Under-desk mounting

2.

Hold the interface with attached brackets against the

 

underside of the desk or other furniture. Mark the

 

location of holes for screws on the desk.

3.

Drill pilot holes 1/4” (6.4 mm) deep, and 3/32” (2 mm)

 

diameter in the table or desk at the marked screw

 

locations from the underside/inside (concealed side) of

 

the furniture, where the interface will be located.

4.

Insert the four wood screws into the pilot holes. Fasten

 

each screw into the installation surface until just less than

 

1/4” of the screw protrudes.

5.

Align the installed screws with the slots in the mounting

 

brackets, and place the interface against the surface, with

 

the screws through the bracket slots.

6.

Slide the interface slightly forward or back, then tighten all

 

four screws to fasten it in place.

Through-desk mounting

1.

If rubber feet were installed on the interface, remove them.

2.

Insert the machine screws that are already installed in the

 

side of the interface through the slots in the through-desk

 

mounting brackets (part #70-077-02), and loosely secure

 

the brackets to the interface (figure 2-2).

3.

Hold the interface with attached brackets against the

 

underside of the desk/table. With a soft pencil mark the

 

location of holes for screws on the desk based on the

 

following:

For the RBG 190 and RGB 192, mark the opening approximately 1.0” x 5.7” ( 2.5 cm x 14.5 cm).

For the RGB 198, mark the opening approximately 1.75" x 13.0" (4.5 cm x 33.0 cm).

2-2

RGB 190F, RGB 192 and RGB 198 • Installation and Operation

RGB 190F, RGB 192 and RGB 198 • Installation and Operation

2-3

Image 7
Contents Analog Computer-Video Interface User’s ManualFCC Class a Notice Extron’s WarrantyTable of Contents One Table of Contents, cont’dIntroductionroduction, cont’d About this Manual FeaturesAbout the RGB 190F, RGB 192 and RGB Introduction, cont’d TwoThrough-desk mounting Tabletop placementMounting the Interfaces Under-desk mountingRack mounting RGB 198 only Installation and Operation, cont’dConnections and Switches Power indicatorSync on green Level and peakingDdsp Mono audio output RGB 192 only, spare on RGB 190F Power connector wiringIf the image does not appear or there is no sound Operation and TroubleshootingAAppendix a ReferencerenceInformation,cont’d Specifications Included Parts Reference Information, cont’dOnly Optional AccessoriesCables RGB 192 onlyReference Information, cont’d