Extron electronic RGB 198, RGB 190F, RGB 192 user manual Operation and Troubleshooting

Page 11

Installation and Operation, cont’d

CAUTION Wiring the audio incorrectly can damage the audio output circuits.

Connect the sleeve(s) to ground (GND). Connecting the sleeve(s) to a negative (-) terminal will damage audio output circuits.

Tip

Mono

Tip

Mono

See caution

L/

Ring

L/

Sleeve

 

Sleeve (s)

 

Tip

R

Tip

R

See caution

Ring

 

 

Unbalanced Output

 

Balanced Output

Figure 2-8 — Wiring the audio output connector

10Unswitched AC outlets —These AC outlets are available in an Edison or Euro plug.

11MAAP openings — Two double MAAP openings, one adjacent to the other, allow up to four single-sized MAAP pass through audio and video connectors.

12Double AAP openings — This plate allows easy access to the back of the MAAPs while safely isolating the power supply and interface.

13IEC AC power plug — Provides convenient power input.

Operation and Troubleshooting

Connect the power cords and turn on the displays (projectors or monitors), audio output devices (sound system) (RGB 192 and 198 only), the interface and the input device (computer). The image should appear on screen, and sound should be audible (RGB 192 and 198 only). If not, ensure that all devices are plugged in and receiving power. Check the cabling and switch settings, and make adjustments as needed.

If the image does not appear or there is no sound

1.

Ensure that all devices are plugged in.

2.

Make sure that each device is receiving power. The

 

interface’s front panel LED lights green if the interface is

 

receiving power and an active sync signal.

3.

Check the cabling and the audio connector wiring and

 

grounding, and make adjustments as needed.

4.

For digital display devices (including LCD, DLP and

 

plasma devices), try turning the DDSP DIP switch (switch

 

4) On (up) or Off (down) on the front panel.

5.

To test the system setup and output, substitute a video test

 

generator for the computer input. Unplug the input and

 

output devices’ and the interface’s power cords, replace

 

the video source with a VTG, then reconnect power cords

 

to restore AC power.

6.

Call the Extron S3 Sales & Technical Support Hotline if

 

needed.

If the image is not displayed correctly

If the output image looks too green, the sync on green (SOG) DIP switch (switch 2) may be set to On (up), and the display device may not be configured to handle SOG signals. Set the switch to Off (down).

If the picture bends or flags at the top of the screen, set the serration pulse DIP switch (switch 3) to Off (down).

For a display device that experiences intermittent glitches, try turning DDSP On (up) or Off (down) using DIP switch 1 on the front panel.

If the picture hangs off the edge of the screen, adjust the Horizontal Shift control.

If the edges of the image seem to exceed their boundaries or if thin lines and sharp edges look thick and fuzzy, try changing the Level DIP switch (switch 1) to On (up). If the image is too bright, turn the Level switch to Off (down).

If the image still does not display correctly, call the Extron S3 Sales & Technical Support Hotline.

If the interface does not respond to controls

If the picture does not move on screen when the horizontal shift control is rotated, DDSP is in use. Set the DDSP DIP switch (switch 4) on the front panel to Off (down).

2-10 RGB 190F, RGB 192 and RGB 198 • Installation and Operation

RGB 190F, RGB 192 and RGB 198 • Installation and Operation 2-11

Image 11
Contents Analog Computer-Video Interface User’s ManualFCC Class a Notice Extron’s WarrantyTable of Contents One Table of Contents, cont’dAbout the RGB 190F, RGB 192 and RGB FeaturesIntroductionroduction, cont’d About this Manual Introduction, cont’d TwoThrough-desk mounting Tabletop placementMounting the Interfaces Under-desk mountingRack mounting RGB 198 only Installation and Operation, cont’dConnections and Switches Power indicatorDdsp Level and peakingSync on green Mono audio output RGB 192 only, spare on RGB 190F Power connector wiringIf the image does not appear or there is no sound Operation and TroubleshootingAAppendix a ReferencerenceInformation,cont’d Specifications Included Parts Reference Information, cont’dOnly Optional AccessoriesCables RGB 192 onlyReference Information, cont’d